Bright 022280 DAB Radio with Bluetooth Instruction Manual
- October 27, 2023
- Bright
Table of Contents
DAB radio with Bluetooth
DAB RADIO WITH BLUETOOTH
OPERATING INSTRUCTIONS
Original instructions
Jula AB reserves the right to make changes to the product. Jula AB claims copyright on this documentation. It is not allowed to modify or alter this documentation in any way and the manual shall be printed and used as it is in relation to the product. For the latest version of operating instructions, refer to the Jula website.
JULA AB 2022-05-04
JULA AB BOX 363, 532 24 SKARA, SWEDEN
EU DECLARATION OF CONFORMITY
Item number 022280
Jula AB, Box 363, SE-532 24 SKARA, SWEDEN This declaration of conformity is issued under the sole responsibility of the manufacturer
DAB+/FM RADIO WITH BLUETOOTH
Conforms to the following directives, regulations and standards.
Directive/Regulation|
Harmonised standard
---|---
RED 2014/53/EU|
EN 62368-1:2014+A11, EN 62479:2010, EN 55032:2015+A1, EN 55035:2017+A11, EN IEC 61000-3-2:2019, EN 61000-3-3:2013+A1, ETSI EN 300 328 V.2.2.2, ETSI EN303 345-1 V1.1.1, Draft ETSI EN 303 345-3 V1.1.0, Draft ETSI EN 303 345-4 V1.1.0,
Eco design Regulation (UE) 2019/1782
|
RoHS 2011/65/EU + 2015/863| EN 50581:2012
This product was CE marked in year:
Skara 2022-03-25
FREDRIK BOHMAN BUSINESS AREA MANAGER
DoC: EN
SAFETY INSTRUCTIONS WARNING!
- Check that the mains voltage corresponds to the rated voltage on the type plate.
- Do not expose the product to rain or moisture – risk of fire and/or electric shock.
- Never open the casing – risk of electric shock. Service must only be carried out by qualified personnel.
- Do not leave the batteries in the battery compartment for too long. Remove the batteries to avoid leakage and damage.
- To ensure normal functionality and long life span, do not expose the appliance to extreme temperatures or high relative humidity.
- Never put the appliance in the bathroom, or near a stove or radiator.
- If the appliance does not work correctly take it to the
nearest service centre. Do not attempt to repair it yourself.
SYMBOLS
SYMBOLS
|
Read the instructions.
---|---
CE
|
Approved in accordance with the relevant directives.
---|---
|
Recycle discarded product in accordance with local regulations.
DESCRIPTION
- Info/Menu
- Alarm
- Preset/Set
- Select
- Mode
- Scan
- Previous
- Next
- Carry handle
- LCD display
- Vol +
- Vol –
- Power
- Speaker
- USB port
- Slot for Micro SD card
- AUX input
- Micro USB input
- Headphone jack
- Antenna
- Battery cover
FIG. 1
Charger with Micro USB included.
TECHNICAL DATA
Rated voltage 230 V ~ 50 Hz
Battery 3x R14/UM2/C
Speaker 8 ohm
Output 1.4 W
Bluetooth 5.0
USE
BATTERY
Open the battery cover and insert the batteries in the direction shown in the battery compartment.
CHARGER WITH MICRO USB
Connect the Micro USB power cord to a the Micro USB port on a mobile device, or a charger for a power point to run without batteries.
SWITCHING ON/OFF
-
Pull out the antenna and angle it for the best reception.
-
Start the radio.
– Press Power. Press Power once again to activate standby mode.
– Press in POWER to switch off. -
Press Mode to switch between DAB, FM, AUX-IN, BLUETOOTH, USB and CARD (memory card).
VOLUME
- Press Vol+ to increase the volume and Vol- to lower the volume.
- The speakers switch off when the headphone connection is used.
DAB MODE
IMPORTANT:
- If there is no reception for DAB+, reposition the product and adjust the antenna. Press Scan to do a new search.
- Interference can occur and loss of sound if the reception is inadequate. Reposition the product to improve the reception.
Automatic station search
- Press MODE and select DAB mode.
- The first time the radio is switched on it selects DAB mode automatically and immediately starts to search for DAB stations. Allow the search process to finish.
- Use the arrows to go to the required station.
- Press Scan to do a new search.
Manual station search
- Press MODE and select DAB mode.
- Press Menu/Info until Manual tune mode is shown on the display. Press Select to confirm.
- Use the arrows to scroll between the stations. Press Select to confirm.
FM RADIO
Press Select to switch audio modes between mono and auto.
Automatic station search
- Press Mode and select FM mode.
- Press Scan for automatic frequency searching.
– Press Scan once again to find the next station.
– Press Scan to search backwards to the previous station.
Manual station search
Use the arrows to set the station manually.
PRESET STATIONS
20 DAB and 20 FM stations can be saved. A saved frequency is erased when a new station is saved in its place.
- Set the required frequency in DAB or FM mode.
- Press Preset until Preset Empty is shown on the display. Use the arrows to select the station position (1-20).
- Select the station number and confirm with Select. Once the station is saved, the saved frequency is shown instead of Preset Empty.
- Press Preset once and use the arrows to listen to a saved station. Confirm with Select.
AUX INPUT
- Press Mode and select AUX.
- Connect an AUX cable from the output on an audio unit, such as a portable MP3 player, to the AUX input.
- Start the audio playback on the audio unit.
USB & MEMORY CARD
NOTE:
A locked Micro SD card cannot be detected or played.
- Press Mode and select USB or CARD.
- Connect a USB unit or memory card.
- Press Scan to select play or pause. Use the arrows to change tracks.
BLUETOOTH
NOTE:
The connection is broken if the unit is moved out of range (approx. 10 m). Move the unit within range again to restore the connection.
- Press Mode and select Bluetooth.
- Activate Bluetooth on the unit and connect to the radio.
- Press Scan to select play or pause. Use the arrows to change tracks.
ALARM
-
Start the radio.
-
Press Alarm. Use the arrows to make the following selections, while the display flashes, and confirm with Select:
– on/off
– time hour
– time minutes
– alarm mode: Daily/Once/Weekends/Weekdays
– types of alarm: Beeper1/FM/DAB/Beeper2
– alarm volume -
Press Alarm once to switch off the alarm.
FACTORY RESET
- In DAB or FM mode. Press Info/Menu.
- Use the arrows to scroll to Factory Reset. Select Yes. Confirm with Select.
- All settings are reset to the factory default settings.