SPYCLOPS PRO SPYP-NVR8POE1T 8 Channel POE 4K NVR with 1TB HDD User Guide

SPYCLOPS PRO SPYP-NVR8POE1T 8 Channel POE 4K NVR with 1TB HDD User Guide

Please read the Quick Start Guide fully before using the product and keep it for your records. Related tools and documents of products, please download from http://www.spyclopsusa.com.

Statement

Thank you for purchasing our products, if you have any questions about setup or product use, please contact support. This manual is used for NVR’s.

Safety Precautions

1. Please modify default password immediately after the equipment is installed, to avoid
   unauthorized access.

2. Please do not place and install the equipment in direct sunlight or near heating equipment.

3. Please do not install the equipment in wet, dusty or locations with smoke.

4. Please keep the NVR installed level and secured to prevent the product from falling.

5. Do not drop or splash liquid onto the NVR and ensure that no liquid-filled items are placed on the device to prevent liquid from leaking into the device.

6. Please install the equipment in a well-ventilated area and do not block the vents of the
   equipment.

7. Please use the equipment within rated input/output range only.

8. Please do not disassemble the equipment without notifying supplier.

9. Please transport, use and store the equipment in climate controlled environment with regulated humidity and temperature.

About

This manual is used as a guide. Pictures, charts, images and all other information provided are for description and explanation only. This manual’s product descriptions and illustrations may vary from the actual products purchased.

Due to future product software upgrades or other design changes, Metra may update this manual. Please visit the company’s official website for the latest version (www.spyclopsusa.com).

NVR Quick Installation Guide

This NVR is convenient can be easily installed, plug and play and no complex setup needed.
Installation Preparation

Install NVR hard drive. Make sure all power is disconnected before installing. Installation tools: Phillips screwdriver.

(Please use surveillance grade hard disk drive only to avoid poor drive performance)

Note: Images for instruction use only, your unit may look different but use the same methods

Interface Description

NVR Illustration

PoE NVR rear panel

Non-PoE NVR rear panel

NVR rear panel interface is similar with pictures above, but the product appearance, including buttons, interfaces and layout are for reference only and may differ from the product you have purchased.

Local Basic Operation

Boot Up

Make sure the input voltage matches the NVR consumption. Connect the device to the monitor and to the power adapter (if available). Plug in the power, switch on the power button (if available), then the device will boot up.

NOTE:

1. It is recommended that you use only the included power supply.
2. You should reset the device administrator password (the system default username is
   “admin” and the password is “12345”) when booting for the first time. To ensure the security of the device, please save the admin login password and modify it regularly.

Modify Password

Step 1: After the device is powered on, select the system language, click “Apply”, enter the
password, click “Login”, click “Modify”.
Step 2: Enter the new password and confirm password, tick off the “Unlock Pattem” to draw twice the consistent unlock pattern consisting of 4-9 points.

Step 3: Set the security question, select the security question 1, 2, 3 by the pull-down operation, and set the answer to the corresponding security question.
Step 4: Insert the USB flash drive into the device, and click “Export Key > Comfirm > Save”. The password is changed.

Quick Configuration

After the device is powered on, the user can configure the system time, network configuration, format hard disk, channel addition and other parameters of the device through the Wizard.

NOTE:
The hard disk must be formatted when installing it for the first time.

Network Configuration

Network parameters must be properly configured before operating the device over the network.

Step 1：On the preview interface, right-click to enter the menu, and click ” TCP/IP “.

Step 2: Modify the IP address of the device according to the actual network plan. (The default IP
address of the NVR is 192.168.1.88).

Add IP Device

Recording Configuration

Playback

Note : Images for instruction use only, your unit may look different but use the same methods

Normal Event

Step 1: On the preview interface, right-click to enter the menu, and click ” Normal Event”
to enter the Motion detection interface.

Step 2: Choose “Event Type > Channel > Enable” and set the corresponding alarm parameters. The device’s normal event alarms include Motion Detection, Video Tampering, Video Loss,
Alarm Input, Alarm Output, Exception, and Buzzer.

Smart Event

Step 1: On the preview interface, right-click to enter the menu, and click ” ” Smart Event” to enter  the Smart Event-Face interface.

Step 2: Select the smart event alarm mode for setting the channel. Smart event alarms supported by the device include Human, Face, Face Comparison. Each smart detection can be configured with different alarm processing rules.

NOTE:
1. Only IPC channels that support smart functions such as face detection and face comparison can set smart event function on this interface.
2. Each channel of a smart event can set up to 1 face detection rule, 4 crossover detection rules, 4 regional intrusion rules, 4 people stay detection rules, and 4 people gathering rules.

Note: Images for instruction use only, your unit may look different but use the same methods

Browser NVR Login

１. Login to NVR on LAN (PC & NVR connected to same router LAN)

1. Make sure the NVR and the connected PC (computer) are in the same segment. If not, please set IP address of your PC to the same segment as the XVR’s, for example ‘192.168.1.33’， but it must be different IP as the XVR’s.
   ( Note: NVR default IP address is 192.168.1.88).

2. Open IE (Internet Explorer) browser , Select Tools > Internet Options > Safety > customized.

3. Open “Search Tool”, double-click the target device from the search result to enter the login interface, or open the IE browser to enter the NVR address: such as http://192.168.1.88/ (If port 80 of the NVR is changed , you need to add the changed port) to enter the login interface.

4. On login interface, login to NVR (Notes: Default user: ”admin”,password: ”12345”.).

5. Web page live view for NVR. On “Live Video” interface, click “Play” icon to play video.

Mobile App Access

Download and install SpyclopsPRO on a smart phone or tablet using either option below:

1. On the Android App Store or iPhone App Store enter “SpyclopsPro” search, download and
   install.

2. Scan the following QR codes to download and install the App.

Run the SpyclopsPRO App (new users need to register an account to log in first). The steps to
add devices are as follows: To add with LAN Search method follow steps 1 – 9.2 and for QR scan replace 5.1 – 7.1 with 5.2 – 6.2.

1. Tap “Tap to select Camera”

2. Tap “My devices”

3. Tap the check box for the NVR/XVR to add all cameras or tap individual cameras and tap
   “Done”

4. Enjoy your live view cameras!

How to playback recorded videos with app

1. Tap “Tap to select Camera”
2. Tap “My devices”
3.  Tap the check box for the camera to view recorded videos and tap “Done”
4. Swipe left or right on the time line to change the recording time view.
   Note: Green bars are recording from schedule and Red is from motion detection.

©2020 Metra Electronics Corporation
460 Walker Street, Holly Hill, FL 32117-2699 Specifications
are subject to change without notice.
All trademarks are the property of their respective owners.
386-255-0234 • www.spyclopsusa.com

8-C HANNEL POE 4K NVR – 1TB HDD

SPYP-NVR8POE1T

8-CHANNEL POE 4K NVR – 1TB HDD

SPECIFICATIONS

SALES 386-255-0234

Read More About This Manual & Download PDF:

References

• Metra Home Theater Group
• spyclopsusa.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>