BRIGHT SunBell Smart Wall Charger Instruction Manual

BRIGHT SunBell Smart Wall Charger

SunBell Smart Instruction Manual

The BRIGHT SunBell Smart is a solar-powered lamp that can be used as a portable lantern, hanging light, reading light, or flexible torch. It can also charge your phones and other low-voltage devices.

Box Content
The box contains the following items:

• Light & battery unit
• Lamp shade
• Solar panel & cable unit
• 2-way charging cable

The following are the components of the SunBell Smart:

• Solar charging port
• Barrel jack (Power in)
• Battery indicator
• Power button
• USB charging port (*)
• Micro-USB (Power out)
• USB connector

(*)The Micro-USB cable can be replaced by other types of USB cables (USB-C, lining, etc.) that work for your phones and devices.

Assembling your SunBell
To assemble the light & battery unit with the lamp shade:

1. Insert the battery unit into the shade.
2. Insert the light unit into the shade.

To remove the light & battery unit from the lamp shade, please take the steps in reverse order.

Light Modes
The SunBell Smart has three light modes for full battery run time and solar run time:

Note: Max working hours may vary between units and places of use. The numbers above are estimates based on optimal working  conditions.

Product Usage

The SunBell Smart can be used in the following ways:

• Emergency light: Press the power button quickly twice to activate the emergency strobe light.
• Turn off the light: After 5 seconds without pressing the power button, the next press will always turn OFF the light.
• Reading/task light
• Flexible torch
• Hanging light
• Lantern
• Emergency strobe light
• Hands-free light
• Loudspeaker (*)

(*) Connect your phone or devices to SunBell Smart with a USB cable and start charging. A phone/device will not charge if the battery is low.

With a power output of 5V at 0.5A, SunBell Smart can charge a variety of phones and small devices. Some phone models / small tablets may not accept the charging current from SunBell Smart.

Charging your SunBell

The SunBell Smart can be charged in two ways:

• Solar charging: Charging time varies depending on sun conditions.
• USB charging: Charging time is approximately 2 hours.

To charge your SunBell Smart:

1. Take the cable out of the back of the solar panel.
2. Connect the solar panel to the battery unit.
3. Place the solar panel in direct sunlight to charge the battery.

Battery Indication

The battery indication for the SunBell Smart is as follows:

30 min of Light)

When the battery is almost empty, the main light will blink 3 times and automatically dim down to the low setting for a final 30 min of light. A 30 second safety light is available when the button is pressed again.

Maintaining your SunBell
To maintain your SunBell Smart:

• Regularly wipe the solar panel to clean from dust and dirt using a soft cloth. DON’T use chemicals!
• Make sure sockets are covered when DON’T use the solar panel as no cable is connected. Avoid dirt and the base of the lamp. This might moisture getting into the sockets. break the solar panel surface.
• Keep the light and battery unit in a dry place with no direct sunlight.
• Don’t keep the light and battery unit in water or with direct sunlight.

BRIGHT SunBell Smart is a solar-powered lamp that can be used as a portable lantern, hanging light, reading light, or flexible torch. It can also charge your phones and other low-voltage devices. Kindly follow these instructions for its optimal use.

Box content

The Micro-USB cable can be replaced by other types of USB cables (USB-C, lining, etc.) that works for your phones and devices.

Assembling your SunBell

To assemble light & battery unit with lamp shade:

• Step 1: Insert batt ery unit into the shade
• Step 2: Insert light unit into the shade
  To remove the light & battery unit from the lamp shade, please take the steps in reverse order.

Light modes

Full battery run time:

Solar run time:

Max working hours may vary between units and places of use.
The numbers above are estimates based on optimal working conditions.

Emergency light:
Press the power button quickly twice to activate the emergency strobe light.

Turn off the light:
After 5 seconds without pressing the power button, the next press will always turn OFF the light.

Product usage

Connect your phone or devices to SunBell Smart with a USB cable and start charging.
A phone/device will not charge if the battery is low.
With a power output of 5V at 0.5A, SunBell Smart can charge a variety of phones and small devices. Some phone models / small tablets may not accept the charging current from SunBell Smart.

Charging your SunBell

Solar charging

Charging time varies depending on sun conditions.

• Take the cable out of the back of the solar panel.
• Connect solar panel to battery unit.
• Place solar panel in direct sunlight to charge the battery.

USB charging

Battery indication

Charging

In use

Maintaining your SunBell

• Regularly wipe the solar panel to clean from dust and dirt using a soft cloth. DON’T use chemicals!

• Make sure sockets are covered when no cable is connected. Avoid dirt and moisture getting into the sockets.

• DON’T use the solar panel as the base of the lamp. This might break the solar panel surface.
  

• Keep the light and battery unit in dry place with no direct sunlight.

• DON’T keep the light and battery unit in water or with direct sunlight .

Technical data

Battery
7.5 Wh NMC battery (2,200 mAh at 3.7 V) 4+ year lifespan (1,500 charge cycles)

Materials
PP, ABS, PMMA, Steel and Aluminium

The battery is made to last 1,500 cycles or 4 years and must be replaced by a qualified agent

LED type Samsung
The light source contained in this luminaire must be replaced by the manufacturer or his service agent or a similar qualified person.

Warranty

This product has been tested and certified to IEC TS 62257-9-5 and IEC TS 62257-9-8.

Limited Product Warranty for SunBell Smart
BRIGHT PRODUCTS AS warrants that the product has been carefully tested, inspected and left the Factory in a proper working condition, free of visible defects. BRIGHT PRODUCTS AS warrants the product to be free from defects in material and workmanship, under normal use and operation, for a period of two (2) years after the date of sale/handover to consumer.
“The product” in this warranty is defined as the “SunBell Smart” solar lamp, consisting of the following main parts delivered in the unit packaging:

1. The SunBell stand/lamp shade
2. The SunBell Smart LED lamp & battery unit
3. The SunBell Solar panel with cable

The warranty is limited to the free replacement of the defective main part(-s) or replacement of the entire product during the two years of warranty. Defective
parts/products replaced under this warranty shall become the property of BRIGHT PRODUCTS.

The above stated Warranty is subject to the following conditions:
Products are sold by authorized BRIGHT PRODUCTS AS representatives. The products are operated and maintained in accordance with BRIGHT PRODUCTS operating instructions, maintenance instructions and specifications. Utilization of only BRIGHT PRODUCTS AS authorized parts and accessories.
The warranty shall not apply to damages resulting from normal wear and tear of product use, nor shall it apply to any product, which has been subject to damages, alterations or misuse by the purchaser. Parts of the product, which would be generally considered as expendable service items during normal use, such as cardboard
box/packaging items, instruction manual etc., are not covered by the warranty.
The warranty does not cover replacement of the entire product or the USB mobile phone charger if the mobile phone used has specifications that does not comply with the charging current or specifications for the SunBell 80 and the USB charger.

How to make a warranty claim:
Warranty claims must be made directly to the point of purchase with a valid proof of purchase. If the warranty claim is found to be valid upon point of inspection, a replacement product or part will be handed out or ordered for hand out at a later date. If there is doubt about the validity of the warranty claim, the product may be kept by the seller to consult with importer or BRIGHT Products AS. BRIGHT Products AS and our representatives are not liable for products that are damaged or lost in transit. If needed, we recommend that you ship your returned products to point of purchase via a trackable shipment method.
THERE ARE NO WARRANTIES, WHICH EXTEND BEYOND THIS DESCRIPTION, AND EXPRESSLY NO IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL BRIGHT PRODUCTS BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUEN-TIAL DAMAGES OR ANTICIPATED LOSS OF PROFITS SUFFERED BY THE PURCHASER. BRIGHT PRODUCTS AND OUR RESELLERS HAVE NO LIABILITY FOR ANY DAMAGE OR DESTRUCTION TO CONSUMER ELECTRONICS DEVICES OR OTHER PERSONAL PROPERTY THAT ARE USED IN CONNECTION WITH THE PRODUCTS, INCLUDING, BUT NOT LIMITED TO, LAPTOPS, CELL PHONES, MP3 PLAYERS, DVD PLAYERS OR HANDHELD DEVICES, OR ANY LOSS OF DATA CONTAINED IN THE FOREGOING DEVICES. NOTWITHSTANDING ANY DAMAGES THAT YOU MIGHT INCUR FOR ANY REASON WHATSOEVER (INCLUDING, BUT NOT LIMITED TO, ALL DAMAGES REFERRED TO HEREIN AND ALL DIRECT OR GENERAL DAMAGES IN CONTRACT, TORT (INCLUDING NEGLIGENCE OR OTHERWISE), THE ENTIRE LIABILITY OF BRIGHT PRODUCTS AND ANY OF ITS SUPPLIERS SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR THE PRODUCT.
SOME STATES AND/OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.

BRIGHT is a Norway-based company with a mission to deliver solutions for better off grid living. Bright’s products bring better, cleaner and safer light to the millions of people without electricity.
Read more about us and our products on bright-products.com
Designed in Norway By K8 Industridesign

References

• BRIGHT Products — Power In Your Hands
• BRIGHT Products — Power In Your Hands

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>