HALO LT56-750LM All-Purpose LED Retrofit Trim Kit Instruction Manual
- June 13, 2024
- HALO
Table of Contents
LT56-750LM All-Purpose LED Retrofit Trim Kit
Instruction Manual
IB51898723
LT56-750LM – 5 CCT instruction sheet
Packaging Contents
A. LED module and connector
CCT Selector Switch (2700K, 3000K, 3500K, 4000K & 5000K)
Choose your favorite correlated color temperature (CCT) from 5 options using
the switch
E26 Edison screw base adapter (For retrofit only – see included retrofit instructions)
Gasket (Use as applicable, per local code)
ITEMS REQUIRED
(Purchase separately)
- Gloves
- Ladder
- Screwdriver
- Safety Glasses
IMPORTANT SAFETY INSTRUCTIONS
Read and follow these instructions and heed all warnings, including those on
the product. Failure to do so may result in serious bodily injury or property
damage.
When using product, basic precautions should always be followed, including the
following:
-
Read and follow these instructions.
-
HALO® recessed luminaires (fixtures) are designed to meet the latest NEC requirements and are certified in full compliance with UL.
Before attempting installation of any recessed lighting luminaire check your local electrical code. This code sets the wiring standards for your locality and should be carefully studied before starting. -
SAVE THESE INSTRUCTIONS AND WARNINGS.
Risk of Fire – MINIMUM 90°C SUPPLY CONDUCTORS.
If uncertain, consult an electrician.
Risk of Electric Shock – To avoid possible electrical shock, be sure that
power supply is turned off at fuse box or circuit breaker before installing or
servicing luminaire.
Risk of Fire/Electric Shock
– LED Retrofit Kit installation requires knowledge of luminaires electrical
systems.
If not qualified, do not attempt installation. Contact a qualified
electrician. Luminaire wiring and electrical parts may be damaged when
drilling for installation of LED retrofit kit. Check for enclosed wiring and
components.
Risk of Fire/Electric Shock –
Install this kit only in luminaires that have the construction features and
dimensions shown in the photographs and/or drawings and where the input rating
of the retrofit kit does not exceed the input rating of the luminaire.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
Edges may be Sharp –
Wear gloves while handling.
- Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
- Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- Please examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
- This device is not intended for use with emergency exits.
- For Canada only per CSA C22.2 No. 250.116, retrofits for luminaire conversion: The retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction. Product must be installed by a qualified electrician in accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local or national regulations for electrical installations.
Risk of Fire/Electric Shock
- LED connector is compatible with Halo 5” H550 and E550 and 6” H750 and H2750 Series LED luminaires.
- LED connector meets California Title-24 high-efficacy luminaire standard as a non-screw base socket.
- LED connector is a nonscrewbase luminaire disconnect for tool-less installation.
NON-SCREWBASE LED LUMINAIRES The LT56 Selleck Table is UL Certified for use with any 5” or 6” diameter recessed luminaire constructed of steel or aluminum with an internal volume that exceeds 107.9 in 3 addition to those noted below and does not exceed the input rating of the luminaire.
- HALO®: H7ICAT, H7ICT, H7T, H7ICATNB, H7ICTNB, H7TNB, H7UICAT, H7TCP, H7RICAT, H7RICT, H7RT, H27ICAT, H27T, H27RICAT, H27RT, H5ICAT, H5ICATNB, H5RICAT, H5T, H5TNB, H5RT, H25ICAT, H25ICATNB, E27ICAT, E27RICAT, E27RTAT, E27TAT, E7ICAT, E7ICATNB, E7RICAT, E7RTAT, E7TAT, E7TATNB, E5ICAT, E5ICATNB, E5RICAT, E5RTAT, E5TAT, E5TATNB, H7UICAT, H7ICATNB, H7ICTNB, H7TNB, H7UICAT, E27RICAT, H25RICAT
- HALO® LED: H750ICAT, H750RICAT, H750T, H750TCP, H2750ICAT, H2750RICAT, H550ICAT, H550RICAT, E550ICAT, E550RICAT, E750ICAT, E750RICAT, H750FR2ICAT, H550FR2ICAT
- HALO® LED Retrofit: ML7BXRFK, ML7E26RFK
- Juno: IC22, IC22R, IC22W, IC22S, IC23, IC23W, IC21, IC21R, IC2, TC2, TC2R, IC20, IC20R, IC25, IC25R, IC25W, IC25S, TC20, TC20R
- Lightly: 1104ICS, 1104ICR, 1104SIC, 1104SICR, 1004ICS, 1004ICR, 1004SIC, 1004SICR
- Capri: CR1, PR1, QL1, R9ASIC
- Lithonia: L7X, L7XP
- Thomas: PS1, R9ASIC/PS9RM
- Prestolite: IBXS
- Commercial Electric: C7ICA (H3), H18
- Elko: (HL7ICA) EL7ICA
For additional information, please refer to the latest Halo LED Specification sheet found at www.cooperlighting.com.
Risk of Electric Shock – To avoid possible electrical shock, be sure that power supply is turned off at fuse box or circuit breaker before installing or servicing luminaire.
DIMMING
The Halo LED luminaire can be dimmed with phase- control dimmers (leading edge
and trailing edge phase cut). Refer to product specifications and dimming
information at www.cooperlighting. com; and consult the dimmer manufacturer
for their latest dimmer listings, load ratings and product information.
COLOR SELECTION
The Selector Switch allows the choice of several different color temperature
options (switch set to 3000K by default). To view the different color options,
move the switch position to the desired color temperature. Power does not need
to be disconnected during color selection.
Retrofit Installation Into E26 Edison Screw Base Recessed Luminaires
- Remove mounting bracket and plate from inside existing recessed luminaire (if installed).
- Remove socket from plate (if installed).
- Screw Edison base adapter (E) into existing Edison base socket in luminaire (Figure 1).
- Plug the orange connector on LT56 LED module (A) into the orange connector included with the screw base adapter (B) (Figure 2).
- Bundle any excess length of wire inside the luminaire (above the module) in preparation for insertion.
- Install the module. (See MOUNTING section for specific instructions)
Retrofit Installation Into Halo H27050X, H550X and H750X Series LED (Non-Screw
Base) Housings
Note:
Complaint with energy codes requiring non screw base sockets.
- Insert orange LED connector from module to Halo recessed fixture connector.
- Squeeze Torsion Springs together and install into torsion spring brackets inside the recessed housing.
- Carefully route wires into fixture and push module up flush to ceiling surface.
MOUNTING
Note:
A round foam gasket has been provided for installation if local code requires.
- Properly wire the unit as instructed in the WIRING section of these instructions.
- For installation into a 6” luminaire, simply press each leg of the torsion springs together and insert them through the receivers inside the luminaire. (Figure 3)
- For installation into a 5” luminaire, loosen each screw of the torsion spring bracket and slide them into the 5” position as marked on the bracket. Retighten the screw. Now, press each leg of the torsion springs together and insert them through the receivers inside the luminaire.
Note: For easiest installation, insert both sides of the torsion springs simultaneously (versus one at a time).
REWIRING OR UNINSTALLING LT56 SeleCCTable LED MODULE
- Pull down firmly on the module until it can’t continue downwards.
- Reach between the flange of the module (inside the can) and squeeze the torsion spring legs together to remove them from the luminaire receptors.
- Disconnect the LED module wiring from the recessed luminaire (LED connector or screw-in Edison base).
5-YEAR LIMITED WARRANTY
Limited warranty for five years, based on up to 6 hours of usage per day.
Additional terms and conditions apply. For more details, please visit:
www.cooperlighting.com/warranty
FCC Statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with ISED ICES Standard Canada ICES-005(B) / NMB-005 (B).
Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com
Canada Sales
5925 McLaughlin Road
Mississauga, Ontario L5R 1B8
P: 905-501-3000
F: 905-501-3172
Cooper Lighting Solutions is a
registered trademark.
All trademarks are property
of their respective owners.
Product availability, specifications, and compliances are subject to change
without notice
© 2023 Cooper Lighting Solutions
All Rights Reserved
Printed in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>