VIVO STAND-V101GT Pneumatic Arm Single Ultrawide Monitor Desk Mount Instruction Manual
- June 13, 2024
- Vivo
Table of Contents
Pneumatic Arm Single Monitor Desk Mount
Instruction Manual
SKU: STAND-V101GT
STAND-V101GT Pneumatic Arm Single Ultrawide Monitor Desk Mount
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/stand-v101gt
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
| help@vivo-us.com
---|---
| www.vivo-us.com
Chat live with an agent!
| 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
TOOLS NEEDED
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1 – Option A – Clamp
Connect Clamp Brace (L) to Base (A) using M6x12mm Screws (S-A) and 4mm Allen
Wrench (T-B).
Remove protective film from Soft Pad (J) and apply to the underside of Clamp
Brace (L). Loosen the screws on the back of Lower Clamp (M) using 4mm Allen
Wrench (T-B), leaving 6mm of thread exposed.
Desk Thickness 0.4” to 2.25” (10mm-58mm)
Hang Clamp (M) into the top 4 slots on Clamp Brace (L). Tighten rear screws
with 4mm Allen Wrench (T-B). Place Clamp Plate (H) on top of the clamp bolts
on Clamp (M).
Desk Thickness 2” to 3.35” (50mm-85mm)
Hang Clamp (M) into the lower 4 slots on Clamp Brace (L). Tighten rear screws
with 4mm
Allen Wrench (T-B). Place Clamp Plate (H) on top of the clamp bolts on Clamp
(M).
Install to desk and tighten clamp bolt using 6mm Allen Wrench (T-C). Snap Cover (K) onto the back of assembled base.
STEP 1 – Option B – Grommet
Attach Grommet Plate (I) to Base (A) using M6x12mm Screws (S-A) and 4mm Allen
Wrench (T-B).
Remove protective film from Soft Pad (J) and apply to the underside of Grommet
Plate (I).
Position Base (A) over grommet hole in desk. If there is no existing grommet
hole, drill a 0.375” (10mm) hole through the desktop in the desired mounting
position.
Remove a single clamp bolt from Clamp (M) using 6mm Allen Wrench (T-C). Insert
clamp bolt with Clamp Plate (H) through the underside of the desk and secure
to Base (A) using 6mm Allen Wrench (T-C).
STEP 2
Screw Pole (B) into Base (A), and tighten set screws using 3mm Allen Wrench
(T-A). Slide Pole Cable Clip (C) onto Pole (B).
STEP 3
Slide Arm Support (D) onto Pole (B) and tighten using 6mm Allen Wrench (T-C).
Place Lower Arm (E) on top of Arm Support (D). Tighten set screw using 3mm
Allen Wrench (T-A) to secure in place.
STEP 4
Place Gas Spring Arm (F) on top of Lower Arm (E), and tighten set screw on
Lower Arm (E) using 3mm Allen Wrench (T-A) to secure.
Connect VESA Plate (G) to Gas Spring Arm (F) using Spacer (S-B), M8x25mm Screw
(S-C), and 6mm Allen Wrench (T-C). Ensure that hexagon side of spacer is
facing upward towards VESA Plate (G).
Remove Thumbscrew (G1) from back of VESA Plate (D). Separate Front VESA Plate
(G2) from Back VESA Plate (G3). Set aside.
STEP 5
Connect Front VESA Plate (G2) to back of Monitor using appropriate Screws
(M-A, M-B), M5 Washers (M-C), and a Phillips Screwdriver.
STEP 6
To mount the monitor, begin by lining up the tabs on Front VESA Plate (G2)
with the slots on Back VESA Plate (G3). Insert tabs into slots and re-install
Thumbscrew (G1) into Back VESA Plate (G3) to secure.
STEP 7
While holding the arm in the horizontal position, adjust the gas spring
tension using 6mm Allen Wrench (T-C).
CAUTION – To avoid damage to the monitor and mount, always keep the arm in a horizontal position while making adjustments.
How to adjust if…
ARM DROPS – If the arm drops, turn the adjustment screw counter clockwise until it holds the monitor in a horizontal position.
ARM RISES – If the arm raises up, turn the adjustment screw lock wise until it holds the monitor in a horizontal position.
STEP 8
Remove cable cover on Gas Spring Arm (F) using a Phillips screwdriver. Slide
cable cover on Lower Arm (E) forward to remove.
Organize cables, then reinstall cable covers to arms. Use Cable Clip (C) to route cables.
Adjust as Desired
To adjust tilt tension, use 6mm Allen Wrench (T-C).
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
LAST UPDATED: 04/06/2023 REV2
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
| 309-278-5303| AVG. RESOLUTION TIME
(within office hrs): 5M 4S
---|---|---
| www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
| help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Pneumatic Arm Single Ultrawide Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>