VIVO STAND-V100HU Pneumatic Arm Single Ultrawide Monitor Desk Mount Instruction Manual
- June 13, 2024
- Vivo
Table of Contents
VIVO STAND-V100HU Pneumatic Arm Single Ultrawide Monitor Desk Mount Instruction Manual
https://vivo-us.com/products/stand-v100hu
help@vivo-us.com
http://www.vivo-us.com
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1 – Option A – Clamp Mount
Attach Clamp Brace (D) to Base (A) using M6x12mm Screws (S-F), and tighten with 4mm Allen Wrench (T-B). Insert M10x63mm Clamp Bolts (S-A) into Clamp Bracket (G) as shown, then place Clamp Plate (F) on top of assembled clamp.
Install Clamp Bracket (G) to upper holes of Clamp Brace (D) for a desk thickness of 3/8” to 1-1/2” (10 – 40mm), or to lower holes for a desk thickness of 1-1/2” to 3-1/4” (40 – 84mm).
Place assembled base on edge of desk and tighten clamp bolts evenly with 6mm Allen Wrench (T-C).
STEP 1 – Option B – Grommet
Place M8x105mm Carriage Bolt (S-B) into square holes in Grommet Base Plate (E). Attach Grommet Base Plate to Base (A) using M6x12mm Screws (S-F) , and tighten with 4mm Allen Wrench (T-B)
Place assembled base over cable grommet hole in desktop, and tighten using Support Plate (J) , M8 Washers (S-C) and M8 Nuts (S-D) , and tighten with Wrench (T-A).
STEP 2
Insert the Arm (B) into the socket of the Base (A), then secure using the 4mm Allen Wrench (T-B) or a flatblade screwdriver. Install Rear Cover (C) to Clamp Brace (D) if the clamp option was used.
Install Arm Washer (S-J) to the top of Arm (B)
STEP 3
Connect VESA Plate (I) to Arm (B) using Spacer (S-G), M8x25mm Screw (S-I), and 6mm Allen Wrench (T-C). Ensure that hexagon side of Spacer is facing upward towards VESA Plate (I). Remove Thumbscrew (I1) from back of VESA Plate (I). Separate Front VESA Plate (I2) from Back VESA Plate (I3). Set aside.
STEP 4
OPTION A: VESA 75×75, 100×100
Install the VESA Plate (I) to monitor using M4x12mm Screws (M-A) or
M5x12mm Screws (M-B) with M5 Washers (M-C) , making sure the rounded
edges of the rear bracket are facing up.
OPTION B: VESA 200×100
Install the 200×100 VESA Plate (H) to the VESA Plate (I) using the
M4x8mm Screws (S-E) and M4 Nuts (S-H) , tightening with Wrench
(T-A) and a Phillips screwdriver. Mount assembled VESA plate to monitor
using M4x12mm Screws (M-A) or M5x12mm Screws (M-B) with M5 Washers
(M-C) , making sure the rounded edges of the rear bracket are facing up.
STEP 5
To mount the monitor, begin by lining up the tabs on Front VESA Plate (I2) with the slots on Back VESA Plate (I3). Insert tabs into slots and re- install Thumbscrew (G1) into Back VESA Plate (G3) to secure.
STEP 6
While holding the arm in the horizontal position, adjust the gas spring tension using the 6mm Allen Wrench (T-C).
STEP 7
Remove cable covers from base and adjustable arm. Organize cables and reinstall cable covers to base and adjustable arm.
Adjust as Desired
To adjust tilt tension, use 6mm Allen Wrench (T-C).
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Pneumatic Arm Single Ultrawide Monitor Desk Mount with USB – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>