VIVO STAND V002O Pneumatic Arm Dual Monitor Desk Mount Instruction Manual

VIVO STAND V002O Pneumatic Arm Dual Monitor Desk Mount

Product Information
The Pneumatic Arm Dual Monitor Desk Mount (SKU: STAND-V002O) is a versatile and adjustable desk mount designed to securely hold two monitors. It comes with a range of hardware and accessories for easy installation. The mount is compatible with monitors weighing between 4.4 and 19.8 lbs (2-9kg) per arm.

Package Contents

• (x2) Lower Arm
• (x2) Upper Arm
• (x1) Base
• (x2) VESA Plate
• (x1) Upper Clamp
• (x1) Lower Clamp
• (x1) Grommet Plate
• (x1) Knob
• (x2) M6x8mm Screw (S-A)
• (x2) M6x10mm Screw (S-B)
• (x2) M8x30mm Screw (S-C)
• (x8) M4x12mm Screw (M-A)
• (x8) M5x12mm Screw (M-B)
• (x8) M5 Washer (M-C)
• (x1) 4mm Allen Wrench (T-A)
• (x1) 5mm Allen Wrench (T-B)

Please note that some hardware included may not be used.

Warnings

1. Tipover Warning: The use of tip-over restraints may reduce the risk of tip-over, but not eliminate it.
2. Choking Hazard: This product contains small parts and is not suitable for children under 3 years. Adult supervision is required.
3. Do not exceed weight capacity. Failure to do so may result in serious injury.

Product Usage Instructions
Step 1 (Option A) – Clamp Installation

1. Remove the plastic shroud from the Base (C) and adjust the knob completely down on the Lower Clamp (F).
2. For 0.4-1.90″ (10-50mm) desktops, install Upper Clamp (E) to Base (C) using M6x8mm Screws (S-A) and 5mm Allen Wrench (T-B). Reinstall the plastic shroud onto Base (C).
3. Attach Lower Clamp (F) to the top two holes on Upper Clamp (E) using M6x10mm Screws (S-B) and 4mm Allen Wrench (T-A). Secure the clamp assembly to the desktop.

Step 1 (Option B) – Grommet Installation

1. Mark two drilling locations 2″ (51mm) apart in the desired location.
2. Drill grommet holes using a 3/8″ (10mm) drill bit, drilling completely through the desktop.
3. Disassemble Lower Clamp (F) using the Phillips end on 5mm Allen Wrench (T-B).
4. Place Grommet Plate (G) on Knobs (F1, H) and secure the assembly to the desktop.

Step 2 – Arm Installation

1. Place Lower Arms (A) onto Base (C) and Upper Arms (B) onto Lower Arms (A).
2. Tighten set screws using the flathead end on 4mm Allen Wrench (T-A).

Step 3 – VESA Plate Installation

1. Attach VESA Plates (D) to Upper Arms (B) using M8x30mm Screws (S-C) and 5mm Allen Wrench (T-B).

Step 4 – Monitor Installation

1. Install two Screws (M-A or M-B) and M5 Washers (M-C) to the top VESA holes on the monitor using the Phillips end on 5mm Allen Wrench (T-B). Leave at least 3mm of clearance between the screw and the monitor.
2. Slide the monitor onto VESA Plate (D), ensuring the screws sit within the slots.

Step 5 – Finalize Installation

1. Tighten the top two screws and install the remaining Screws (M-A or M-B) and 5mm Washers (M-C) using the Phillips end on 5mm Allen Wrench (T-B).

Step 6 – Cable Management
Remove the bottom plastic covers from Lower Arm (A) using the Phillips end of 5mm Allen Wrench (T-B). Slide plastic covers off of Upper Arms (B). Run cables from monitors through the bottom of the Upper Arms (A) and Lower Arms (B), then reattach plastic covers.

Step 7 – Final Step
Follow the additional instructions in the user manual or contact customer support for further assistance.

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
• USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
• WARNING: CHOKING HAZARD SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

DO NOT EXCEED WEIGHT CAPACITY
Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1 (Option A)

Clamp Installation Remove the plastic shroud from Base (C). Adjust the knob completely down on Lower Clamp (F). For 0.4”-1.90” (10-50mm) desktops install Upper Clamp (E) to Base (C) using M6x8mm Screws (S-A) and 5mm Allen Wrench (T-B). Reinstall the plastic shroud onto Base (C). Attach Lower Clamp (F) to the top two holes on Upper Clamp (E) using M6x10mm Screws (S-B) and 4mm Allen Wrench (T-A). Secure clamp assembly to the desktop. For 1.8”-3.1” (45-80mm) desktops install Upper Clamp (E) to Base (C) using M6x8mm Screws (S-A) and 5mm Allen Wrench (T-B). Reinstall the plastic shroud onto Base (C). Attach Lower Clamp (F) to the bottom two holes on Upper Clamp (E) using M6x10mm Screws (S-B) and 4mm Allen Wrench (T-A). Secure clamp assembly to the desktop

STEP 1 (Option B)Grommet Installation

Mark two drilling locations 2” (51mm) apart in the desired location. Drill grommet holes using a ⅜” (10mm) drill bit drilling completely through the desktop. Disassemble Lower Clamp (F) using the Phillips end on 5mm Allen Wrench (T-B). Place Grommet Plate (G) on Knobs (F1, H) and secure assembly to the desktop.

STEP 2
Mark two drilling locations 2” (51mm) apart in the desired location. Drill grommet holes using a ⅜” (10mm) drill bit drilling completely through the desktop.

Disassemble Lower Clamp (F) using the Phillips end on 5mm Allen Wrench (T-B). Place Grommet Plate (G) on Knobs (F1, H) and secure assembly to the desktop. Place Lower Arms (A) onto Base (C) and Upper Arms (B) onto Lower Arms (A). Tighten set screws using the flathead end on 4mm Allen Wrench (T-A).

STEP 3
Attach VESA Plates (D) to Upper Arms (B) using M8x30mm Screws (S-C) and 5mm Allen Wrench (T-B).

STEP 4
Attach VESA Plates (D) to Upper Arms (B) using M8x30mm Screws (S-C) and 5mm Allen Wrench (T-B). Install two Screws (M-A or M-B) and M5 Washers (M-C) using the Phillips end on 5mm Allen Wrench (T-B) to the top VESA holes on the monitor leaving at least 3mm of clearance between the screw and monitor. Slide the monitor onto VESA Plate (D) making sure the screws sit within the slots.

STEP 5
Tighten the top two screws and install the remaining Screws (M-A or M-B) and 5mm Washers (M-C) using the Phillips end on 5mm Allen Wrench (T-B).

STEP 6

STEP 7
Remove bottom plastic covers from Lower Arm (A) using the Phillips end of 5mm Allen Wrench (T-B). Slide plastic covers off of Upper Arms (B). Run cables from monitors through the bottom of the Upper Arms (A) and Lower Arms (B), then reattach plastic covers.

STEP 8

Remove bottom plastic covers from Lower Arm (A) using the Phillips end of 5mm Allen Wrench (T-B). Slide plastic covers off of Upper Arms (B). Run cables from monitors through the bottom of the Upper Arms (A) and Lower Arms (B), then reattach plastic covers. Adjust monitor tilt support using a 5mm Allen Wrench (T-B) as shown. Adjust monitor position as desired

Love your new VIVO setup and want to share?
Tag us in your photo!

Open Monday – Friday 7:00 am – 7:00 pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product

AVG. RESPONSE TIME (within office hrs): 1HR 8M help@vivo-us.com

• 23% within < 15m
• 38% within < 30m
• 61% within < 1hr
• 83% within < 2hr
• 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT:www.vivo- us.com

References

• Register a .US.COM domain today!
• VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
• Pneumatic Arm Dual Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>