Tidoin 700100 Wall Lamp Instruction Manual

Tidoin 700100 Wall Lamp

Product Information

The product is a light fixture with a motion sensor. It operates on a 120V, 60Hz supply circuit and uses a 1E26100W Max bulb type. The suggested bulb type is an 11W LED A19, which is not included in the package. The fixture comes with various components including a junction box, leading wires, universal mounting bracket, mounting screws, studs, back plate, washer, and cap nut. It also includes other parts such as wire nut, fixture wire, socket, fixture frame, glass, and glass clip.
The user manual provides instructions on assembly, installation, and operation of the product. It explains how to replace damaged glass and provides diagrams for different operating modes.

Product Usage Instructions

1. Open the box and carefully take out all the components, parts bag, and manual.
2. Check all the components against the parts list to ensure nothing is missing or damaged. If any parts are missing or if the glass is damaged, contact the manufacturer for a replacement.
3. If the glass is damaged, unlock the glass clips on the bottom of the fixture frame to release the damaged glass. Replace it with a new glass and clip the glass clips again to fix it.
4. Follow the provided illustration for assembly and wiring:
   • I. Connect wires (A) using wire nuts (Code I).
   • II. Connect fixture wire (B) to socket (C) and fixture frame (D).
   • III. Connect fixture wire (B) to junction box (J).
   • IV. Install bulb (G) and secure it with glass clip (F) and glass (E).
5. The product has different modes of operation:
   • Day & 15 Sec Night: The light works when motion is detected during the day and stays on for 15 seconds at night.
   • Dual-bright Test mode: Press the tact switch to test the dual-bright mode.
   • ON/OFF Test mode: Press the tact switch to test the ON/OFF mode.
   • Dual-bright mode: The light works at night when motion is detected.
   • ON/OFF mode: The light works at night when motion is detected.
   • Manual override: Press the tact switch to manually override the light and keep it on.
6. There are additional operating diagrams provided for low-level brightness dimming, dual-bright mode, ON/OFF mode, and manual override mode.
7. Important notes:
   • Clean the lens every 1 or 2 months with a soft cloth to maintain maximum sensitivity.
   • Install the fixture at a height of 6-8 feet above the ground for optimal performance.
   • The sensor detects motion across a range of 220 degrees.
   • The sensor is more sensitive to motion across its detection path than motion directly towards it.
   • Avoid mounting the fixture near heat sources like air conditioners, vents, or furnaces to minimize nuisances.

MODEL : 700100, 700101

IMPORTANT SAFETY INSTRUCTIONS

• Warning : If any special control devices are used with this fixture, follow the instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electric contractor.
• Warning : This product can expose you to chemicals including lead, which is known to the State of California, to cause cancer or birth defects or other reproductive harm. For more information, please go to www.P65Warnings.ca.gov
• Caution : Electrician installation highly recommended. All glass is fragile, use care when handling glass component(s) and or lamp(s). Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.

Important Notice:

• This is a generic instruction sheet used for various fixtures.
• The shape and style of fixture / glass / shade / diffuser may vary.

(Required Supply Circuit: 120V, 60Hz. Bulb Type: 1E26100W Max)

The mostly suggested bulb type is 11W LED A19. Dimmable bulb is required for the motion sensor featured light to ensure dim light functions well.

COMPONENTS INCLUDED IN THE PACKAGE

ASSEMBLY & INSTALLATION STEPS

1. Open the box from top, take out all the components, parts bag and manual from the box carefully.
2. Check all the components against the parts list. Make sure get each parts on list. If any parts missing and glass damage, please contact manufacturer at: support@micsiu.com to get a replacement.
   Parts are NOT included for which is shown as 0 under QTY

PARTS LIST                     (Parts QTY X 2 for 2 pack item)

Part Name| QTY| Code| | Part Name| QTY| Code
Junction Box| 0| A| Wire Nut| 3| I
Leading Wires| 2| B| Fixture Wire| 2| J
Universal Mounting Bracket| 1| C| Socket| 1| K
(1.25″) Mounting Screw| 2| D| Fixture Frame| 1| L
Studs| 2| E| Glass| 4| M
Back Plate| 1| F| Glass Clip| 8| N
Washer| 2| G| Bulb| 0| O
Cap Nut| 2| H| | |

Refer to the illustration while doing assembly and follow the steps as below:

• I Screw the bulb (O) onto socket (K) before installation.
• II Thread two studs (E) onto the mounting bracket (C) at proper position. Then attach the mounting bracket (C) to the junction box (A) by two mounting screws (D). Adjust the mounting bracket to a horizental level.
• III Connect wires according to the wiring diagram as below.
• IV Attach the backplate (F) to two studs (E) and fix with two washers (G) and cap nuts (H).

In a case of glass damage, unlock the glass clips (N) on the bottom of fixture frame (L) to release the damaged glass, then carefully replace with a new glass and clip the glass clips (N) again to fix the glass (M).

Function and Operation

MODES OF OPERATION

NOTE:

1. The sensitivity of the motion sensor will increase as the environmental temperature gets cooler. For best performance, gently clean the lens with a soft cloth every 1 or 2 months to assure maximum sensitivity.
2. For best performance, install fixture at 6~8 feet above the ground. At such a height, the lantern will provide a detection distance of up to 40 feet at 77 degrees Fahrenheit.(See Fig.4)
3. The sensor detects across a detection range of 220 degrees.(See Fig.5)
4. The sensor will be more sensitive to motion across its detection path than motion directly towards it. (See Fig.6)
5. To reduce possible nuisances, do not mount the fixture near a heat source like an air conditioner, vent or furnace exhaust, or in a direction facing any reflecting object or other light source.

Troubleshooting

connections.
| Wall switch or circuit breaker is off| Turn on a switch or circuit breaker.
| Light bulb may be dead.| Test the light bulb in a known working light
| | fixture
In Dual-bright mode or ON/OFF mode , the lighting fixture does not turn on when there is motion| Light bulb is loose.| Tighten the light bulb in the socket.
Incorrect or loose wire connections.| Check wire connections.
| | | | |
| Too much sunlight is shining into the Dusk-to-Dawn| Relocate fixture| away| from| a| western
| sensor in the early evening.| facing wall.| | | |
| Too much light is shining onto the Dusk-to-Dawn| Eliminate or turn off other light source,
| sensor due to another light source, such as a street| block other light source from shining onto
| lamp or other light fixture.| Dusk-to-Dawn sensor, or relocate fixture.
In Dual-bright mode or ON/OFF mode , the lighting fixture stays on at 100% brightness continuously.| False triggering caused by a heat source, such as street or sidewalk traffic, a heater or dryer vent, or air conditioning vent, or heated swimming pool.| Eliminate heat source or relocate fixture
The lighting fixture comes on at 100% brightness for no apparent reason| False triggering caused by a heat source, such as street or sidewalk traffic, a heater or dryer vent, or air conditioning vent, or heated swimming pool.| Eliminate heat source or relocate fixture
The lighting fixture comes on during the daytime or too early in the evening| The fixture may be installed in a shaded area, such as under a porch or eave, preventing daylight from shining onto the Dusk-to-Dawn sensor.| Relocate the fixture
The LED bulb or fluorescent bulb| Non-dimmable LED bulb or fluorescent bulb is used| Replace dimmable LED bulb or fluorescent
flickers when the lighting fixture is| on the lighting fixture.| bulb, or incandescent bulb
dimmed down to the stand-by dimming level.| |
A small number dimmable LED bulbs or fluorescent bulbs do not match.| Press the tact switch continuously to change the low-level brightness to avoid
| | the flickers point.
In Dual-bright mode, the standby| A small number dimmable LED bulbs or fluorescent| Press  the  tact  switch  continuously  to
brightness is close to the full| bulbs do not match.| reduce the low-level brightness to increase
brightness.| | the difference from full brightness.
In Manual override, the light stays on after dawn| The ambient light level is too low| Relocate the fixture

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>