Tidoin 4-Light Black Iron Ceiling Lamp Chandelier Pendant with Geometric Cage Instruction Manual

: October 30, 2023
: Tidoin

Table of Contents

Tidoin 4-Light Black Iron Ceiling Lamp Chandelier Pendant with Geometric
Product Information
IMPORTANT SAFETY INSTRUCTIONS
COMPONENTS INCLUDED IN THE PACKAGE
PARTS LIST
ASSEMBLY & INSTALLATION STEPS
Wiring
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Tidoin 4-Light Black Iron Ceiling Lamp Chandelier Pendant with Geometric

Cage

Product Information

Product Model: 900003/900004
Supply Circuit: 120V, 60Hz
Bulb Type: 4E2660W Max
Compatible Bulb Type (NOT Included): 9W LED ST58 bulb
Components Included in Package: Canopy with mounting kits & ground wire/Stems/Pipes/Frames/Rod/Light cluster
Parts Included in Parts Bag

IMPORTANT SAFETY INSTRUCTIONS

Warning: If any special control devices are used with this fixture, follow the instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, please contact a qualified electric contractor.
Warning: This product can expose you to chemicals including lead, which is known to the State of California, to cancer or birth defects or other reproductive harm. For more information, please go to www.P65Warnings.ca.gov
Caution: Electrician installation highly recommended. All glass is fragile, use care when handling glass and or lamp(s). Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.

Important Notice:

This is a generic instruction sheet used for various fixtures.
The shape and style of the fixture/glass/shade/diffuser may vary.

$Tidoin-4-Light-Black-Iron-Ceiling-Lamp-Chandelier-Pendant-with-Geometric- Cage- $1$$

COMPONENTS INCLUDED IN THE PACKAGE

$Tidoin-4-Light-Black-Iron-Ceiling-Lamp-Chandelier-Pendant-with-Geometric- Cage- $2$$

PARTS LIST

$Tidoin-4-Light-Black-Iron-Ceiling-Lamp-Chandelier-Pendant-with-Geometric- Cage- $4$$

PARTS LIST

Part Name| QTY| Code| | Part Name| QTY| Code
Junction Box| 0| A| 12″ Stem| 4| K
Supply Wires| 0| B| Ring| 1| L
Wire Nut| 3| C| Cap| 1| M
Mounting Bracket with Studs| 1| D| Top Frame| 1| N
Mounting Screw| 2| E| Central Rod with Swivel| 1| O
Grounding Wire| 1| F| Screw| 16| P
Canopy with Swivel| 1| G| Light Bulb| 0| Q
Cap Nut| 2| H| Square Pipe with Tabs| 4| R
6″ Stem| 1| I| Light Cluster| 1| S
Fixture Wire| 2| J| Bottom Frame| 1| T

ASSEMBLY & INSTALLATION STEPS

Open the box from top, take out all the components, parts bag and manual from the box carefully.
Check all the components against the parts list. Make sure get each parts on list. If any parts missing or glass damage, please contact manufacturer at: support@micsiu.com to get a replacement.
Parts are NOT included for which is shown as 0 under QTY.
Refer to the illustration while doing assembly and follow the steps as below:
Attach the top frame (N) onto the tabs of the TOP of four square pipes (R) by the screws (P), do not fasten the screws yet. Attach the bottom frame (T) onto the tabs of the BOTTOM end of the pipes (R) by the screws (P). Adjust four pipes, top and bottom frames to a perfect position, then fasten the screws.
Release the ring (L) from the top of the central rod (O) first, then insert the rod (O) with fixture wires (J) into the central hole of top frame (N), slide on the cap (M) to cover the top openning of top frame (N), then fix it in position with the ring (L). Thread the other end of central rod (O) with the light cluster (S). Place the wires (J) through the central rod (O) for later installation.
Determine how many stems should be assembled according to your desired hanging height. Thread the short and long stems (I & K) onto the central rod (O) one by one, and attach the stems onto the swivel of the canopy (G). Fixture wires (J) go through the stems (K & I) and canopy (G) for later wiring. $Tidoin-4-Light-Black-Iron-Ceiling-Lamp-Chandelier-Pendant-with-Geometric-Cage- $7$$
Adjust the studs on the mounting bracket (D) to a proper protrusion if necessary. As for a test, slide the canopy (G) onto the studs to figure if the cap nuts (H) cover the protrusion properly. Thread the studs toward the junction box (A) a little bit if it protrudes from the canopy (G) too much. Attach the mounting bracket (D) to the junction box (A) by two mounting screws (E).
Connect wires according to the wiring diagram on the right.
Slide the canopy (G) to the studs on the mounting bracket (D), then fix it with two cap nuts (H). $Tidoin-4-Light-Black-Iron-Ceiling-Lamp-Chandelier-Pendant-with-Geometric-Cage- $10$$
Screw the light bulbs (Q) into four sockets on the light cluster (S). $Tidoin-4-Light-Black-Iron-Ceiling-Lamp-Chandelier-Pendant-with-Geometric-Cage- $11$$

Wiring

Illustration of assembly and wiring:

$Tidoin-4-Light-Black-Iron-Ceiling-Lamp-Chandelier-Pendant- with-$3$$

Missing parts? Glass damage? Any questions?
Please email us at: support@micsiu.com We are always here to help you fix the problems you are facing.