Tidoin FYC-YDW9-126 Foldable Electric Treadmill User Manual

October 30, 2023
Tidoin

FYC-YDW9-126 Foldable Electric Treadmill

Tidoin FYC YDW9 126 Foldable Electric Treadmill  User Manual

INSTRUCTION

Thank you very much for purchasing our product.
Please read this instruction carefully before use it and keep the instruction at proper place.

1. CAUTION
To avoid any hurts, please read this manual carefully before using.

Tidoin FYC YDW9 126 Foldable Electric Treadmill  - fig

  • For safety purpose do not stand on running belt while start.
  • Please stop immediately for any feeling of vomit jerky during using.
  • Please increase speed slowly if needed.
  • Adjustment of belt is prohibited during using.
  • It is suggested to wear sports shoes when using the machine.
  • Children elder pregnant women patients are prohibited to use the machine.
  • Please clip the safety key on your clothing during using.
  • Please firmly hold the hard bars during using.

SAFETY NOTICE

  1. Please put the machine on flat ground. It is unsuitable to put the machine at following places:
  2. Outdoors.(The machine is specially designed for indoor use only)
  3. Slant ground or slant places on balcony.
  4. Sunlight area or near heater.
  5. Big noisy places.
  6. Error may be appeared if the power is not stable. Please do not use the same socket together with computer air conditioner etc.
  7. It is suggested to wear sports shoes and gym suit when use the machine.
  8. Please increase or decrease speed slowly.
  9. Be careful of children or other objects while fold and unfold the machine.
  10. Do not put the machine near to wet object. Error maybe caused by waterdrop.

CAUTION DURING USE

  • If you do not feel well before using, please consult with your doctor or coach.
  • It is not our company’s responsibility for any improper use by user to cause body injured.
  • Please pull up plug after using.
  • Please pull out plug for any movement or change parts for the machine.
  • Children elder and pregnant women are prohibited to use the machine. Patients need doctor’s consultant before using.
  • Please place the machine on flat places. Do not locate any objects 2M behind the machine.
  • Do not start the machine when it is folded.
  • Waterdrop is prohibited to run into the machine , especially to motor, power line and plug.
  • Danger may cause if wearing long dress or other unsuitable dresses during use.
  • Enclose spaces, air uncirculated places and with flammability places are prohibited to use the machine.
  • Do not put any objects on the machine.
  • Put away the plug from heated place or fire seat.
  •  Please switch off all functions and pull out plug after using.
  • Please do not stand directly on the belt while starting the machine.
  • Do not disassemble the machine without conduct of professional person.
  • Please make sure the running belt is fastened before using.

Technical Specification

Product Name Treadmill
Voltage 110V
Frequency 60Hz
Speed 1.0-12 Kh / 0.6-7.5 mph

Product Spare Parts

Tidoin FYC YDW9 126 Foldable Electric Treadmill  - fig
2

Serial NO. Part Name Spec qty unit
1 Rotary Knob M8*20 2 PCS
2 T Shape Knob / 2 PCS
3 Safety Key / 1 PCS
4 Silicone Oil / 1 PCS
5 Allen Wrench / 1 PCS

Assembly Instruction

Tidoin FYC YDW9 126 Foldable Electric Treadmill  - fig
3

  1. Take out the treadmill from the box. Place the machine flat on the ground, lift both sides of the frame.
  2. Insert a T-shaped knob underneath the frame to secure the tubes.
  3. Remove the preset screw on the top of the tubes, place the panel with handrail in place. And then connect the wire on the right tube. Please note that do not press the wire in case of being damaged/broken. Fix the handrail to the tubes using the rotary knob.
  4. Slowly insert the pad stand into the panel opening. Place the safety key in the yellow panel to complete the assembly.

Control Panel

Tidoin FYC YDW9 126 Foldable Electric Treadmill  - fig
4

1. Window Display
1.1 “TIME”, “STEP” window: display exercise time and step number. The forward countdown time is from 00:00 to 99:59; the countdown countdown decreases from the set time to 00:00.
When the countdown (setting range: 5: 00 ~ 99: 00) to 00:00, the treadmill stops smoothly and stops at a slow speed Run and display “End”, and enter standby mode after 5 seconds. “STEP” window: Forward step count is from0~9999.when forward countdown reaches the top point, it will recount.
1.2 “DISTANCE”, “CALORIES” window: display the current exercise distance and calories.
The distance forward counts from 0.00 to 99 miles, and restarts counting from 0.0 after overflow; the countdown distance (setting range 1 mile to 99 miles) decreases from the current set value to 0.0, after which the treadmill stops and displays End, After 5  seconds, it enters standby mode.
The positive calorie count starts from 0 to 9999, and starts counting again from 0 after overflowing. When the calorie counts down (setting range 20 to 990), it starts to decrease from the set value to 0, and after the countdown reaches 0, the treadmill smoothly  slows down. Stop running and display “End”, and enter standby mode after 5 seconds. Press the “mode” key in the state of exercise to switch the cycle display or fixed display of exercise distance and calories.
1.3 “SPEED” window: display the current speed value, setting and display range 0.57.5MPH/1-12KMH.
The step by pressing the plus and minus keys is 0.1KMH. P1 ~ P12 are displayed under the setting of automatic program selection.
1.4 After the treadmill is started, each display item is cycled at an interval of 5 seconds. You can press the “mode” key to switch between cycle display and single item display.

2. Remote Control Buttons
2.1 “Start / Stop” key: If you press the start key in standby mode or countdown mode to start the treadmill, the default speed is 1MPH. If you press Start under the fixed program, the treadmill will act according to the preset value and accumulate the value.
2.2 “Start / Stop” key: Press this key in the running state to decelerate and stop the exercise  and return to the standby interface. Press the stop button for more than 2 seconds, the system restarts.
2.3 “+” and “-” are speed up and down keys: setting status, used to adjust the setting value. It is used to adjust the speed after startup, and its adjustment amplitude value is (0.1KMH) / time.
When it is continuously pressed and held for no more than 0.5 seconds, it will continuously increase or decrease. It can be used to adjust the value in the setting state.
2.4 “M” key: Select the mode to be switched in the pending state. Including time countdown (setting range 5:00 ~ 99:00), distance countdown (setting range 1 ~ 99), calorie countdown (setting range 20 ~ 990). Switch between cycle display and fixed display after the treadmill starts.
2.5 “P” Set automatic programs P01 ~ P12, a total of 12 fixed programs.

3. Function Mode Description
3.1 Sports Mode: Press the START key to start quickly, the SPEED window displays “3 2 1”, the treadmill executes P00, the time is counted (0: 00 ~ 99: 59, overflow is re-timed from 0: 00), the default speed is 1.0KMH, Press the speed plus or minus button to adjust the speed.
3.2 Countdown Mode: In standby mode, press the mode key to enter the time countdown (time range 5: 00 ~ 99: 00, default 30:00), distance countdown (distance range 1 mile ~ 99 mile, default 1.0 mile) ), Calorie countdown (calories range 20 ~ 990 kcal,  default 50 kcal).Use the speed plus and minus keys to set the relevant countdown value. After the setting is completed, press the “Start” key to start the treadmill. The treadmill starts counting down from the set value and counts down to 0. The treadmill stops automatically and The corresponding window displays “End” and enters standby mode after 5 seconds.
3.3 Fixed program (P01 ~ P12): Press the mode button continuously to select one of the modes P01 ~ P12. The default is 30:00. Press the START button to execute the program. The treadmill operates according to the preset value of the fixed program. The time  interval (Time / 20 ) * Change the speed once in 60 seconds. The speed plus and minus keys cannot adjust the speed during running. Each program changes by 20 segments. See the fixed program table for preset fixed program values.

Tidoin FYC YDW9 126 Foldable Electric Treadmill  - fig
6

4. Panel Buttons
4.1 “Start / Stop” key: If you press the start key in standby mode or countdown mode to start the treadmill, the default speed is 1.0 KM/H. If you press Start under the fixed program, the treadmill will act according to the preset value and accumulate the value.
4.2 “Start / Stop” key: Press this key in the running state to decelerate and stop the exercise and return to the standby interface. Press the stop button for more than 2 seconds, the system restarts.
4.3 “+” and “-” are speed up and down keys: setting status, used to adjust the setting value. It is used to adjust the speed after start up, and its adjustment amplitude value is (0.1KMH) / time.
When it is continuously pressed and held for no more than 0.5 seconds, it will continuously increase or decrease. It can be used to adjust the value in the setting state. .

USAGE OF SILICONE OIL

Before you start the treadmill, please lubricate the running belt first. Pull up the running belt slightly, apply silicone oil to the backside of the belt and the top surface of the running deck. Start the treadmill and keep it running for 3 minutes so that the oil spread  and even out. It is necessary to maintain your treadmill every 30 working hours of the treadmill for optimal performance, which also helps extend the service life of parts.

Running Belt Adjust

Tidoin FYC YDW9 126 Foldable Electric Treadmill  - fig
8

  1. Running belt deviate to left
    Start the machine by speed at 1-2 KM/H without loading, use die nut to make the screw go 1/4 circle(see fig1). Then make the machine running without loading 1-2 minutes. Please adjust like this to make the belt till to mid place.

  2. Running belt deviate to right
    Start the machine by speed at 1-2 KM/H without loading, use die nut to make the screw go 1/4 circle(see fig2). Then make the machine running without loading 1-2 minutes. Please adjust like this to make the belt till to mid place.

  3. Running belt logjam
    If the running belt is in dead condition, use die nut to make the screw 1/2 circle both left and right till this logjam solved.

DAILY MAINTAINANCE

  1. Please disconnect power before checking the machine or cleaning.
  2. Clear belt and dial plate after use, at least once a week.
  3. Check and tighten screws and spines at fixing point.
  4. Do not hang clothes or other objects on the machine.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Tidoin User Manuals

Related Manuals