Tidoin 900001 1-Light Bronze Iron Ceiling Lamp Chandelier Pendant Installation Guide

Tidoin 900001 1-Light Bronze Iron Ceiling Lamp Chandelier Pendant

Product Information

• Model: 900001 900002
• Required Supply Circuit: 120V, 60Hz
• Bulb Type: 1E26100W Max (not included)
• Compatible Bulb Type: 9W LED ST58 bulb (not included)
• Components Included in the Package:
  • Canopy with mounting kits & ground wire
  • Stems
  • Rod
  • Pipes
  • Frames
• Parts Included in Parts Bag:
  • Junction Box
  • 12 Stem
  • Ring
  • Wire Nut (3)
  • Cap
  • Mounting Bracket with Studs
  • Top Frame
  • Mounting Screw (2)
  • Central Rod
  • Grounding Wire
  • Screw (16)
  • Canopy with Swivel
  • Square Pipe with Tabs (4)
  • Cap Nut (2)
  • 6 Stem
  • Bottom Frame
  • Fixture Wire (2)

Product Usage Instructions

1. Open the box from the top and carefully take out all the components, parts bag, and manual from the box.
2. Check all the components against the parts list. Ensure that you have all the parts listed. If any parts are missing or damaged, please contact the manufacturer at support@micsiu.com to get a replacement. Parts are not included for which is shown as 0 under QTY.
3. Refer to the illustration of assembly and wiring while doing assembly and follow the steps as below:
4. Attach the top frame (N) onto the tabs of the top of four square pipes (Q) by the screws (P). Do not tighten the screws completely at this stage.
5. Insert the central rod (E) into the bottom frame (I). Attach the bottom frame (I) to the central rod (E) with screws (P).
6. Attach the mounting bracket with studs (B) to the junction box (A) using mounting screws (F).
7. Connect fixture wires (S) with supply wires from junction box (A) using wire nuts (C).
8. Insert the stems (12 Stem and 6 Stem) into the central rod (E).
9. Attach the square pipes with tabs (G) to the bottom frame (I) using cap nuts (H).
10. Attach the canopy with swivel (R) to the square pipes with tabs (G).
11. Attach the top frame assembly to the central rod assembly by tightening screws (P).
12. Install a compatible bulb type (not included).

Note: This is a generic instruction sheet used for various fixtures. The shape and style of fixture/glass/shade/diffuser may vary.

Missing parts? Glass damage? Any questions?
Please email us at : support@micsiu.com
We are always here to help you fix the problems you are facing.

Assembly & Installation Instructions

MODEL: 900001 900002
IMPORTANT SAFETY INSTRUCTIONS:

• Warning: If any special control devices are used with this fixture, follow the instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, please contact a qualified electric contractor.
• Warning: This product can expose you to chemicals including lead, which is known to the State of California, to cause cancer or birth defects or other reproductive harm. For more information, please go to www.P65Warnings.ca.gov
• Caution: Electrician installation highly recommended. All glass is fragile, use care when handling glass component(s) and or lamp(s). Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.

Important Notice:
This is a generic instruction sheet used for various fixtures. The shape and style of fixture / glass / shade / diffuser may vary.

(Required Supply Circuit: 120V, 60Hz. Bulb Type: 1E26100W Max)

Compatible Bulb Type (NOT Included)

The mostly suggested bulb type is 9W LED ST58 bulb

COMPONENTS INCLUDED IN THE PACKAGE

Canopy with mounting kits & ground wire / Stems / Rod / Pipes / Frames

Parts included in parts bag

ASSEMBLY & INSTALLATION STEPS

1. Open the box from top, take out all the components, parts bag and manual from the box carefully.
2. Check all the components against the parts list. Make sure get each parts on list. If any parts missing or glass damage, please contact manufacturer at: support@micsiu.com to get a replacement.
   Parts are NOT included for which is shown as 0 under QTY.

PARTS LIST

Part Name| QTY| Code| | Part Name| QTY| Code
Junction Box| 0| A| 12″ Stem| 4| K
Supply Wires| 0| B| Ring| 1| L
Wire Nut| 3| C| Cap| 1| M
Mounting Bracket with Studs| 1| D| Top Frame| 1| N
Mounting Screw| 2| E| Central Rod| 1| O
Grounding Wire| 1| F| Screw| 16| P
Canopy with Swivel| 1| G| Square Pipe with Tabs| 4| Q
Cap Nut| 2| H| Light Bulb| 0| R
6″ Stem| 1| I| Bottom Frame| 1| S
Fixture Wire| 2| J| | |
3. Refer to the illustration while doing assembly and follow the steps as below:

1. Attach the top frame (N) onto the tabs of the TOP of four square pipes (Q) by the screws (P), do not
   fasten the screws yet. Attach the bottom frame (S) onto the tabs of the BOTTOM end of the pipes (Q) by the screws (P). Adjust four pipes, top and bottom frames to a perfect position, then fasten the screws.

2. Release the ring (L) from the rod (O) first. Insert the central rod (O) to the central hole of the top frame (N), slide on the cap (M) to cover the top of the frame (N), then fix it in position with the ring (L). Place the fixture wires (J) through the center hole of the top frame (N) and ring (L) for later installation.

3. Determine how many stems should be assembled according to your desired hanging height. Thread the
   short and long stems (I & K) onto the central rod (O) one by one, and attach the stems onto the swivel of the canopy (G). Fixture wires (J) go through the stems (K & I) and canopy (G) for later wiring.

4. Adjust the studs on the mounting bracket (D) to a proper protrusion if necessary. As for a test, slide the canopy (G) onto the studs to figure if the cap nuts (H) covers the protrusion properly. Thread the studs toward the junction box (A) a little bit if it protrudes from the canopy (G) too much.
   Attach the mounting bracket (D) to the junction box (A) by two mounting screws (E).

5. Connect wires according to the wiring diagram on the right.

6. Slide the canopy (G) to the studs on the mounting bracket (D), then fix it with two cap nuts (H). VII Screw the light bulb (R) onto the socket on the rod (O).

Illustration of assembly and wiring

Assembly Procedure

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>