Tidoin 900007 3 Light Bronze Iron Ceiling Lamp Chandelier Pendant Instruction Manual

October 30, 2023
Tidoin

Tidoin 900007 3 Light Bronze Iron Ceiling Lamp Chandelier Pendant Instruction Manual
Tidoin 900007 3 Light Bronze Iron Ceiling Lamp Chandelier
Pendant

Assembly & Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS:

  • Warning: If any special control devices are used with this fixture, follow the instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, please contact a qualified electric contractor.
  • Warning: This product can expose you to chemicals including lead, which is known to the Stateof California, to cause cancer or birth defects or other reproductive harm. For more information, please go to www.P65Warnings.ca.gov
  • Caution: Electrician installation highly recommended. All glass is fragile, use care when handlingglasscomponent(s) and or lamp(s). Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation

Important Notice:

This is a generic instruction sheet used for various fixtures. The shape and style of fixture / glass / shade / diffuser may vary.

(Required Supply Circuit: 120V, 60Hz. Watt: 3E2660W Max)

Compatible Bulb Type (NOT Included)

The mostly suggested bulb type is 9W LED ST58 bulb

COMPONENTS INCLUDED IN THE PACKAGE

Rod/Light cluster/Frames/Arms/Strips/Cap/Chain/Canopy with mounting parts/Crystals
Instruction

Parts included in parts bag
Instruction

ASSEMBLY & INSTALLATION STEPS

  1. Open the box from top, take out all the components, parts bag and manual from the box carefully.
  2. Check all the components against the parts list. Make sure get each parts on list. If any parts missingor glass damage, please contact manufacturer at: support@micsiu.com to get a replacement. Parts are NOT included for which is shown as 0 under QTY
    PARTS LIST

    Part Name| QTY| Code| | Part Name| QTY| Code
    Junction Box| 0| A| Screw| 12| N
    Leading Wires| 0| B| Upper Frame| 1| O
    Wire Nut| 3| C| Strip| 3| P
    Mounting Bracket with Studs| 1| D| Light Cluster| 1| Q
    Mounting Screw| 2| E| Bottom Frame| 1| R
    Canopy with Collar Loop| 1| F| Ground Wire| 1| S
    Cap Nuts| 2| G| Fixture Wire| 2| T
    Chain Locker| 2| H| Chain| 1| U
    Loop| 1| I| Ring| 1| V
    Disc| 1| J| Bolt and Washer| 3| W
    Cup| 1| K| Bolt Nut| 3| X
    Arm| 3| L| Crystal| 56| Y
    Central Rod with Nipple| 1| M| Light Bulb| 0| Z

  3. Refer to the illustration while doing assembly and follow the steps as below:
  4. Assemble the upper frame (O), three strips (P) and bottom frame (R) using the screws (N). Refer totheillustration so each part and the top/bottom ends are correctly distinguished before assembly.
  5. Use the bolt nuts (X) to fix three arms(L) to the bolts (W) on the cup (K), attach the other end of thearms(L) onto the upper frame (O), fix with screws (N).
  6. Release the ring (V) from the nipple of central rod (M), insert the rod (M) through the hole of thecup(K), place the disc (J) on the cup, then use the loop (I), ring(V) to fix the disc(J), cup(K) and central rod(M). Connect the light cluster (Q) with central rod (M) from the bottom openning of fixture frame. Fixturewires(T) go through the central rod (M) and loop (I) for later assembly.
  7. Adjust the studs on the mounting bracket (D) to a proper protrusion if necessary. As for a test, slide the canopy (F) onto the studs to figure if the cap nuts (G) cover the protrusion properly. Thread the studs toward the junction box (A) a little bit if it protrudes from the canopy (F) too much. Attach the mounting bracket (D) to the junction box (A) by two mounting screws (E).
  8. Use the chain locker (H) to assemble the canopy (F) and loop (I). Now the fixture assembly is completed. Wires (T) go through the canopy (F) for wiring.
  9. Connect wires according to the wiring diagram on the right
  10. Slide the canopy (F) to the studs on the mounting bracket (D), then fix it with two cap nuts (G)
  11. Hang the crystal (Y) onto the frame one by one carefully, and screw the light bulbs (Z) onto to socket.

Illustration of assembly and wiring

Installation Instruction

Assembly Instruction

Assembly Instruction
Assembly Instruction
Assembly Instruction
Assembly Instruction
Assembly Instruction
Assembly Instruction
Assembly Instruction
Assembly Instruction

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Tidoin User Manuals

Related Manuals