Tidoin 900011 12 Light Bronze Iron Ceiling Lamp Chandelier Pendant Instruction Manual

Tidoin 900011 12 Light Bronze Iron Ceiling Lamp Chandelier Pendant

Product Information

The product is a lighting fixture that comes in various models – 900011, 900012, 900013, and 900014. The fixture needs a supply circuit of 120V and 60Hz and can accommodate bulbs with a maximum wattage of 12E2660W. The mostly suggested bulb type is a 9W LED ST58 bulb, which is not included in the package. The product comes with light cluster, arms, canopy with mounting parts, chain, and mounting bracket. The assembly manual is generic and may vary depending on the shape and style of the fixture/glass/shade/diffuser.

Product Usage Instructions

1. Open the box from the top and carefully take out all the components, parts bag, and manual from the box.
2. Check all the components against the parts list and ensure that you have all the parts. If any parts are missing or damaged, contact the manufacturer at support@micsiu.com to get a replacement.
3. Refer to the illustration provided in the manual while doing assembly and follow the steps below:
4. Assemble six arms (Q) to the light cluster (T) and fix them with cylinder nuts (S). Pull the wires gently through the arms for later wiring with the fixture wires inside the cup (P).
5. Slide cup (P) on arms (Q), then fix it with hex nuts (N) and washers (O) using the Allen wrench (X). Use wire nuts (W) to connect black wires with black, white with white, or according to the wiring diagram.
6. Place disc (M) and ring (L) on top of cup (P) through the short nipple, fix it with loop (K).
7. Thread to open the chain lockers (V) on the ends of the chain (I). Connect one end with loop (K) and fixture, connect the other end with canopy (F). Wires (J) go through hanging loop (G) and canopy (F) for later wiring.
8. Install the mounting bracket with nipple (D) to the junction box (A) by using the mounting screws (E).
9. Connect wires according to the wiring diagram provided in the manual.
10. Thread the hanging loop (G) onto the nipple of mounting bracket (D) to hang the fixture. Thread the collar (H) to fix the canopy (F) onto the junction box.
11. Screw the bulbs (R) on the socket of the light cluster (T).

Assembly & Installation Instructions

MODEL: 900011 900012 900013 900014

IMPORTANT SAFETY INSTRUCTIONS:

• Warning: If any special control devices are used with this fixture, follow the instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, please contact a qualified electrical contractor.
• Warning: This product can expose you to chemicals including lead, which is known to the State of California, to cause cancer or birth defects or other reproductive harm. For more information, please go to www.P65Warnings.ca.gov.
• Caution: Electrician installation is highly recommended. All glass is fragile, use care when handling glass component(s) and or lamp(s). Read the instructions carefully and turn the electricity off at the main circuit breaker panel before beginning installation.

Important Notice:

This is a generic instruction sheet used for various fixtures. The shape and style of fixture/glass / shade/diffuser may vary

The mostly suggested bulb type is 9W LED ST58 bulb

COMPONENTS INCLUDED IN THE PACKAGE: Light cluster / Arms / Canopy with mounting parts / Chain/ Mounting bracket  

ASSEMBLY & INSTALLATION STEPS:

1.  Open the box from top, take out all the components, parts bag and manual from the box carefully.
2. Check all the components against the parts list. Make sure get each parts on list. If any parts missing or glass damage, please contact manufacturer at: support@micsiu.com to get a replacement. Parts are NOT included for which is shown as 0 under QTY.

PARTS LIST

Part Name| QTY| Code|  | Part Name| QTY| Code
Junction Box| 0| A| Disc| 1| M
Leading Wires| 0| B| Hex Nut| 6| N
Wire Nut| 3| C| Washer| 6| O
Mounting Bracket with Nipple| 1| D| Cup| 1| P
Mounting Screw| 2| E| Arm| 6| Q
Canopy| 1| F| Light Bulb| 0| R
Hanging Loop| 1| G| Cylinder Nut| 12| S
Collar| 1| H| Light Cluster| 1| T
Chain| 1| I| Ground Wire| 1| U
Fixture Wire| 2| J| Chain Locker| 2| V
Loop| 1| K| Wire Nut| 5| W
Ring| 1| L| Allen Wrench| 1| X

1. Refer to the illustration while doing assembly and follow the steps as below:
   • Assemble six arms (Q) to the light cluster (T) and fix with the cylinder nuts (S). Pull the wires gently through the arms for later wiring with the fixture wires inside the cup (P).
   • Slide the cup (P) on the arms (Q), then fix with hex nuts (N) and washers (O) using the Allen wrench (X). Use wire nuts (W) to connect black wires with black, white with white, or according to the wiring diagram. Place the disc (M) and ring (L) on the top
   • of cup (P) through the short nipple, fix with the loop (K).
   • Thread to open the chain lockers (V) on the ends of the chain (I). Connect one end with loop (K) and fixture, connect the other end with canopy (F). Wires (J) go through hanging loop (G) and canopy (F) for later wiring. Install the mounting bracket with
   • nipple (D) to the junction box (A) by the mounting screws (E).
   • Connect wires according to the wiring diagram on the right.
   • Thread the hanging loop (G) onto the nipple of mounting bracket (D) to hang the fixture. Thread the collar (H) to fix the canopy (F) onto the junction box.
   • Screw the bulbs (R) on the socket of the light cluster (T).

INSTALLATION

Missing parts? Glass damage? Any questions?

• Please email us at : support@micsiu.com.
• We are always here to help you fix the problems you are facing

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>