TELTONIKA GH5200 Autonomous Tracker with GNSS Instruction Manual

: June 4, 2024
: teltonika

Table of Contents

TELTONIKA GH5200 Autonomous Tracker with GNSS
Know your device
Set up your device
PC Connection (Windows)
Quick SMS configuration
Default configuration settings
Safety information
Precautions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TELTONIKA GH5200 Autonomous Tracker with GNSS

GH5200 is an autonomous personal tracker for lone worker protection.

Know your device

Set up your device

How to insert the Micro SIM card and connect the battery

Remove the cover.
Insert Micro-SIM card as shown with PIN request disabled. Make sure that the Micro-SIM card cut-o corner is pointing forward to slot.
Insert the battery as shown to a device. Position the battery in a place where it does not obstruct other components.
Reattach the cover and tighten the screw.
Micro-SIM card insertion/removal must be performed when the device is powered and the battery is disconnected. Otherwise, the Micro-SIM card might be damaged or the device will not detect it.

PC Connection (Windows)

Turn on your device by holding the power button for around 7 seconds.
Connect the device to a computer using a Micro-USB cable or Bluetooth connection:
- Using Micro-USB cable
- You will need to install USB drivers, see “How to install USB drivers (Windows)” shown below.
- Using Bluetooth
- GH5200 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or another device> Bluetooth. Choose your device named –
- “GH5200_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect and then select Done.
You are now ready to use the device on your computer.

How to install USB drivers (Windows)

Please download COM port drivers from here. here (https://teltonika-gps.com/downloads/en/fmb120/.2. Extract and run TeltonikaCOMDriver.exe.
Click Next in the driver installation window.
. In the following window click the Install button. Setup will continue installing the driver and eventually, the confirmation window will appear. Click Finish to complete the setup.

Configuration (Windows)
At GH5200 device will have default factory settings set. These settings should be changed according to the user’s needs. The main configuration can be performed via Teltonika Configurator software. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

The downloaded Configurator will be in a compressed archive. Extract it and launch Congurator.exe. After launch software language can be changed by clicking in the right bottom corner:

The configuration process begins by pressing on the connected device:

After connection to Concurator Status window will be displayed:

Various Status info tabs display information about GNSS, GSM, I/O, Maintenance and etc. GH5200 has one user editable prole, which can be loaded and saved to the device. After any modification of the congregation, the changes need to be saved to the device using Save to Device button. Main buttons following functionality:

Load from the device – loads configuration from the device.
Save to device – saves the configuration to the device.
Load from le – loads configuration from le.
Save to le – saves the configuration to le.
Update rmware – updates rmware on the device.
Read records – read records from the device.
Reboot device – restarts device.
Reset configuration – sets device configuration to default.

The most important configurator section is GPRS – where all your server and GPRS settings can be configured and Data acquisition – where data acquiring parameters can be configured. More details about GH5200 configuration using Configurator can be found here.

Quick SMS configuration

The default configuration has optimal parameters present to ensure the best performance of track quality and data usage. Quickly set up your device by sending this SMS command to it

Default configuration settings

Movement detection:

Device movement will be detected by accelerometer
Device makes a record On Moving if one of these events happen
Angle dierence between last coordinate
300 seconds passes and current position is greater than 10°
Traveled distance is more than 100 meters
Speed dierence between last coordinate and current position is greater than 10 km/h
1 hour passes while device is stationary
Records sending to server:
If device has made a record it is sent to the server every 120 seconds

Safety information

This message contains information on how to operate GH5200 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

Precautions

Operate the device in suitable conditions
Do not use the device where mobile connectivity is forbidden.
Road safety Comply with local laws, always hold your hands on a steering wheel when using a device. Your safety is of utmost importance when you drive.
Interference All wireless devices are sensitive to electromagnetic interference, as a result wireless devices aect the performance of each other.
Limit the use of device in hospitals Please follow all restrictions. Turn the device in the vicinity of medical devices when required.
Limit the use of device in vehicles Please follow all restrictions. Wireless devices can interfere with other electronic equipment in vehicles.
Be cautious near ammable materials and liquids Charging precautions SELV LPS chargers, personal computers or laptops that device will be connected to must comply with the requirements of IEC 60950:2005 standard.
Use only original batteries Using uncertied manufacturer or dierent type batteries may cause an explosion.
Protect batteries from moisture. Place them in a cool and dry place when storing. Avoid extensive operation at high temperatures. Do not attempt charging battery directly from the electrical mains. All utilised batteries shall comply with IEC 62133.
Power supplies Power supply circuits used to charge the device connection must have safeguards, which prevent power leakage, short circuits or incorrect electrical grounding. Any used switches ought to be installed in a readily accessible location. Power must be uninterrupted and the distance between the contacts must be 3 mm or larger.
Remove device safely Device must be disconnected from computer or charger by unplugging the magnetic USB cable from the device.
In order to prevent device from mechanical damage it is advisable to transport it in a shock–resistant packaging. If device stopped working properly regardless of the settings only a qualied specialist can help. It is recommended to contact your local seller or your UAB Teltonika manager in such a case.
Use the right screwdriver In order to prevent device’s cover from mechanical damage it is recommended to use screwdriver, which is included in the package. Do not use electrical screwdrivers.
https://wiki.teltonika-mobility.com/view/GH5200 Retrieved from “https://wiki.teltonika-mobility.com/wikibase/index.php?title=GH5200_First_Start&oldid=62091″