THUREN FABRICATION 2013-2022 High Clearance Sway Bar Instructions

THUREN FABRICATION 2013-2022 High Clearance Sway Bar

Product Information
Thuren Fabrication 2013 – 2022 High Clearance Sway Bar The Thuren Fabrication High Clearance Sway Bar is designed for use in trucks from 2013 to 2022. It provides enhanced clearance and improved performance for off-road applications. The sway bar is compatible with the following truck models:

• Dodge Ram 3500

Applicable Part Numbers

• [Part Number]

Product Usage Instructions
Remove Stock/Previous Sway Bar
Warning: Before proceeding, ensure that the vehicle is securely supported on jack stands or a vehicle lift.

To remove the stock or previous sway bar, follow these steps:

1. Locate the sway bar underneath the vehicle.
2. Using appropriate tools, unbolt and remove any brackets or mounts securing the sway bar to the vehicle chassis.
3. Once all brackets and mounts are removed, carefully slide out the stock or previous sway bar from its mounting positions.

Installing Sway Bar
Before installing the Thuren Fabrication High Clearance Sway Bar, ensure that all necessary components are included and in good condition.

To install the sway bar, follow these steps

1. Position the Thuren Fabrication High Clearance Sway Bar in the appropriate location underneath the vehicle.
2. Align the sway bar with the mounting points on the vehicle chassis.
3. Securely bolt the sway bar to the vehicle chassis using the provided hardware.

Install End Links
After installing the sway bar, it is necessary to install the end links to complete the installation.

To install the end links, follow these steps:

1. Attach one end of the end link to the sway bar using the provided hardware.
2. Attach the other end of the end link to the axle mount on the vehicle using the provided hardware.
3. Tighten all hardware securely to ensure proper attachment.

Notes: Additional information or specific instructions may be provided in the full user manual. Please refer to the complete manual for further details.

These instructions are applicable to the following Trucks

• 2014 – 2023 Ram 2500
• 2013 – 2023 Ram 3500

Applicable Part Numbers

• (TF-FSWBK-13UHC) 2014-2023 DODGE RAM 2500
• (TF-FSWBK-13UHC) 2013-2023 DODGE RAM 3500

Remove Stock/Previous Sway Bar

• Disconnect Sway Bar Links from Axle and Sway Bar
• Remove hardware from the Sway Bar mount on the frame.
• Remove the Sway Bar from the truck

Warning
On this model Swaybar our swaybar links will mount on the inside/engine side of both the bar and axle mounts.

Installing Sway Bar

• The swaybar will mount with the “THUREN” logo upright.
• Flex the Swaybar frame mount bushings to split them open, slip them over the bar, and then slide the stainless mounting bracket over the bushings.
• Place a Stainless plate between the frame and Sway Bar mounts
• Lift the Sway Bar into position and hand-tighten frame mount hardware
• Using the slots in the frame mounts, center the swaybar side to side between the frame rails. There is not much side-to-side clearance so pay attention here.
• The Urethane frame pivot bushings keep the swaybar from shifting side to side, but there should still be a small gap between the bar stops to allow 1/16″ of side-to-side play.
• Once everything is centered, the Torque frame mount hardware to 45 Ft/Lbs

Install End Links

• Ensure the Sway Bar End Links Sleeve Flange is against the Sway Bar and Axle mounting surface.
• Install Sway Bar End Links. Make sure you can access the grease fittings.
• Torque End Link mounting Hardware to 100 Ft/Lbs

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>