SUNNY HEALTH FITNESS RC2301 Treadmill Remote Control User Manual
- June 10, 2024
- SUNNY Health Fitness
Table of Contents
SUNNY HEALTH FITNESS RC2301 Treadmill Remote Control User Manual
Product Overtawe
BATTERY INSTALLATION & REPLACEMENT
BATTERY INSTALLATION:
- Remove the battery cover.
- Take out the 1pc CR2032 battery that is included inside the remote control box.
- Install the battery into the battery holder with the positive end facing up.
- Put the battery cover back on to the battery holder.
BATTERY REPLACEMENT:
- Remove the battery cover.
- Remove the old battery and install the new battery into the battery holder with the positive pole facing up.
- Put the battery cover back on to the battery holder.
Dispose the old battery according to your regional guidelines.
REMOTE CONTROL FUNCTIONS
Note: If the treadmill does not respond to the remote control, you will need to resync the treadmill and remote control. To sync the remote control with the treadmill, press the start/pause button on the remote control for five seconds, and you will hear a “beep” sound that means the remote control have resynced with the treadmill.
- START/PAUSE BUTTON: Press the START button, so that treadmill begins running. 0.8 KM/H (KM per hour) is the default start speed. During exercise, you also can press this button to pause the machine.
- SPEED +/– BUTTONS: Press the +/- buttons to increase or decrease the speed in increments of 0.1 KM/H (KM per hour). Pressing and holding either of these buttons for a duration of over ½ a second will increase or decrease the speed continually.
- STOP BUTTON : When in use, press the STOP button to terminate your workout session completely. All data will be deleted and reset to the initial setting.
- DISPLAY SWITCH BUTTON : When in use, you can press this button to switch the display between Time, Distance, Calories, Steps and Speed value.
- BATTERY POWER INDICATOR LIGHT: When you press any button on the remote, the light will blink three times if the battery is low. Please proceed to change the battery. If it does not blink, then the battery is not low.
*NOTE : The maximum speed on this treadmill is 6.0 KM/H (KM per hour).
| PROGRAMS | Initial | Default Value | Set Range | Display Range |
|---|---|---|---|---|
| TIME (MIN: SECOND) | 0:00 | – | – | 0:00—99:59 |
| SPEED(KM/H) | 0.0 | 0.8 | 0.8-6.0 | 0.8-6.0 |
| DISTANCE(KM) | 0.00 | – | – | 0.00–99.99 |
| STEP | 0 | – | – | 0-99999 |
| CALORIE(KCAL) | 0 | – | – | 0.0–9999 |
INSTALLATION ET REMPLACEMENT DE LA BATTERIE
INSTALLATION DE LA BATTERIE:
- Retirez le couvercle de la batterie.
- Retirez la pile CR2032 (1 pièce) qui se trouve dans le boîtier de la
- Installez la pile dans le support de pile avec l’extrémité positive vers le haut.
- Remettez le couvercle de la pile sur le support de la pile.
REMPLACEMENT DE LA BATTERIE:
- Retirez le couvercle de la batterie.
- Retirez l’ancienne pile et installez la nouvelle pile dans son support, le pôle positif vers le haut.
- Remettez le couvercle de la pile sur le support de la pile.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
FCC & IC Radiation Exposure Statement:
This equipment complies with FCC and Canada radiation exposure limits set
forth for an uncontrolled environment. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>