SHOWVEN SPARKULAR PRO Weatherproof Enclosure Fountain Machine User Manual
- June 13, 2024
- Showven
Table of Contents
SHOWVEN SPARKULAR PRO Weatherproof Enclosure Fountain Machine
★ Please read this manual carefully before operating this product.
★ Warranty card attached in the manual, please keep it well.
Safety Considerations
- Never touch the nozzle of SPARKULAR PRO, danger of getting burnt.
- Never touch the sparks which shooting out from the nozzle.
- Cover of nozzle of SPARKULAR PRO is prohibited.
- Keep audience, animals or flammable objects at a minimum distance of 3m from SPARKULAR PRO. Make sure sparks shoot out from SPARKULAR PRO can NOT touch any objects in the air.
- Ensure that children, animals and unauthorized persons don’t have access to the SPARKULAR PRO!
- Unauthorized repair are prohibited, it may cause serious incident.
- Make sure lid of feeding hopper are well covered when use SPARKULAR PRO. Accidentally burning of Composite Ti can only use sands to extinguish. Composite Ti should keep away from moisture and stored in a dry sealed environment.
- Please be noted that there may sparks or remains fall to the ground when use HC8200 LARGE, LARGE Ⅰ.
- Clear material is necessary both before and after the show. Please check nozzle of SPARKULAR PRO after each show, if there are consumable agglomerated in the nozzle, please clear it with screwdriver, otherwise it will affect the spark effects and even damage the machine.
- Maximum cascade of SPARKULAR PRO is 5 units (110V version is 3 units) with one standard power cable. Otherwise it may damage the machine and even cause fire.
- For better heat dissipation, block the air intake and air outlet is prohibited.’
Specifications
Model: BT71/BT72
Dimension: 315 x 280 x 255mm
Weight: 14kg
Input: BT71: AC 220VAC-240VAC,50/60HZ; 600W
BT72: AC 100VAC-120VAC,50/60HZ; 700W
Work Temp.: -10°C~50°C
Effect height: HC8200 LARGEⅠ: 6-7m / HC8200 LARGE : 5-6m
Height adjustable: Yes, gear 1~10
Effect direction: Straight up
Hopper capacity: 1200g
Control: DMX
Operating Panel
LED display area:
READY: Turns from flashing into long on, indicates that the machine is
ready to work.
DMX: Flashing shows that DMX signal is connected, light OFF means there
is no DMX signal
FAULT: Light ON when error occurs
HEAT: Light ON when system is heating up
Control Button Area:
MENU: switch through setup menu. Press 3s switch to advanced interface
DOWN: parameter down
UP: parameter up
ENTER: confirm and save parameters
Radio Frequency Identification Area:
RFID card comes together with HC8200. It is a safety design, allows machine to
identify the parameter and types of consumable.
Please note that granules RFID card can increase the single machine specific
working time. The card is disposable, can only use once.
Interface
Main interface:
First line: shows DMX address
Second Line: shows inner temp. and temp. bar, as well as error info if
available
Error Information
| Error Information | Explanation |
|---|---|
| E0 System IC | Systematic error |
| E2 Temp. Sensor | Temperature sensor is not connected or damage |
| E3 P Temp. Over | Chassis over-temperature |
| E4 Time Remain | Activated time for machine is not enough, need to swip RFID |
card
E5 K Temp. Over| Inner core over-temperature
E6 Heat Fail| Heating Fail, if it recovery automatically, problem is shortage
of power supply
Setting Menu
Press “MENU” switch through setup menu
Set DMX Address| 1-512| Set DMX address
If controlled by Host Controller, please set DMX address as 1, 3, 5, 7,…2n-1,
otherwise it may leads to signal interference
---|---|---
Manual Fountain| On/Off| Manual firing, for test only
Fountain Height| 1-10| Manual firing height setup, for test only
Auto Clear Delay| 0.1-0.9s| Auto clear material time after each firing
Advanced Menu
Press “MENU” 3 seconds to enter the advanced setup interface, press MENU key to enter different options, wait 3 seconds to return to the main interface.
| Option | Range | Explanation |
|---|---|---|
| Set Temperature | 580-620 | Default is 580. Please don’t change default value |
without engineer’s suggestion from SHOWVEN.
LCD Backlight| On/Off| LCD screen backlight ON/OFF
Density@ Height 1| 80| Sparks density @ Height gear 1
Density@ Height 2| 80| Sparks density @ Height gear 2
Density@ Height 3| 80| Sparks density @ Height gear 3
Density@ Height 4| 80| Sparks density @ Height gear 4
Density@ Height 5| 80| Sparks density @ Height gear 5
Density@ Height 6| 100| Sparks density @ Height gear 6
Density@ Height 7| 100| Sparks density @ Height gear 7
Density@ Height 8| 100| Sparks density @ Height gear 8
Density@ Height 9| 40-100| Sparks density @ Height gear 9
Density@ Height 10| 40-100| Sparks density @ Height gear 10
Mode Selection| Factory Mode
User Mode
| Factory mode is for engineer only. When in Factory mode
machine can’t controlled by DMX console/host controller
Motor Protect| On/Off| Motor protect function, default setting is Off
Standby Switch| On/Off| When ON, the machine can firing only when heating up
was finished
For better performance of SPARKULAR PRO, please don’t change the default value of density without permission from SHOWVEN.
SPARKULAR PRO occupy 2 channels
| First Channel | Function |
|---|---|
| 0-15 | Firing OFF |
| 16-255 | Firing ON and with adjustable height |
| Second Channel | Funciton |
| 60-80 | Firing ON and with adjustable height |
| 20-40 | Emergency Stop |
| 0-10 | Pre-heat OFF (disabled when auto-heat ON) |
| 240-255 | Pre-heat ON (disabled when auto-heat ON) |
Please follow bellowing rules to set DMX address when use SHOWVEN Host Controller, otherwise it may leads to signal interference.
| Sparkler No. | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DMX Address | 1 | 3 | 5 | 7 | 9 | 11 | 13 | 15 | 17 | 19 | 21 | 23 | 25 | 27 | 29 | 31 | 33 | 35 |
Warranty Instructions
- Sincere thanks for your choosing SPARKULAR PRO, you will receive quality service from us.
- The product warranty period is one year. If there are any quality problems within 7 days after ship ping out from our factory, we can exchange a brand new same model machine for you.
- We will offer free of charge maintenance service for machines which with hardware malfunction (except for the instrument damage caused by human factors)in warranty period. Please don’t repair machine without factory permission.
★ Below situations NOT included in warranty service:
- Damage caused by improper transportation, usage, management, and maintenance, or damage caused by human factors;
- Disassemble, modify or repair products without Showven’s permission;
- Damage caused by external reasons (lightning strike, power supply etc);
- Damage caused by improper installation or use;
For product damage not included in warranty range, we can provide paid service.
★ Invoice and warranty card are necessary when applying for maintenance service from SHOWVEN.
Customer Support
Showven Technologies Co., Ltd
Add: Building B1, Changsha E Center No.18, Xiangtai Road, Liuyang Economic
Development Zone, Changsha City, 410300, Hunan Province, P.R.China.
Tel: +86-731-83833068
Web: www.showven.cn
E-mail: info@showven.cn
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>