SHOWVEN Sparkular Mini for Wedding Stage Party User Manual

SHOWVEN Sparkular Mini for Wedding Stage Party

User Manual Sparkular mini

• Please read this manual carefully before operating this product.
• This manual contains the warranty card, please keep it well.

Security Considerations

• Unauthorized repair are prohibited, it may cause serious incident.
• Keep SPARKULAR mini dry and do NOT use in rain or snow.
• Make sure lid of feeding hopper are well covered when use Sparkular mini.Acci dentally Burning of Composite Ti can only use sands to extinguish. Composite Ti should keep away from moisture and stored in a dry sealed environment.
• Keep audience and flammable material at a minimum distance of 3m from SPARKULAR mini. Make sure sparks shoot out from Sparkular mini can NOT touch any objects.
• Clear material for Sparkular mini is necessary.

Responsibility Excellence Innovation

Sparkular Mini Model No.BT06

__

__

__

__

__

__

__

__

| Parameter
__

Size

| __

168×180×228mm

__

Weight

| __

4.5kg

__

Input Parameter

| __

200-240VAC, 50/60Hz

__

Working Power

| __

300w

__

Working Temperature

| -10℃~ 50 ℃
__

Casing

| __

ABS

__

Fountain Height

| 2.0m~3.5m,Depend on different type of composite Ti
Interface| Double DMX input interfaces, double AC power interfaces

Advantages

• Integrating wireless technology,Not exposed,anti-collision.
• One button start.
• Tilt protection function. More secure.
• Sophisticated design, light-weighted and portable.

Operation Panel

LCD information display area, showing operate menu and working status of machine.

Light-emitting diode display area：

Control button area：

• READY： After turn on machine, it will automatically preheat around 5 minutes, when the
• “READY” green light turns from flashing into long on, indicates that the machine is ready to work.
• DMX： Flashing shows that DMX signal is connected, otherwise is without signal.
• FAULT： When any malfunction , the light turn on.
• HEAT： When the machine is heating, signal light turn on.

Radiofrequency identification area：

• Composite Ti with RFID card, swiping cards used to identify parameters and types of granules.
• Please note that granules RFID card can increase the single machine specific working time. The card is disposable,one card can only use one time.

Interface

Main Interface

• First line: Display DMX address is “1”.
• Second line: Display the present inner core temperature and the temperature progress bar; display remaining time is 7 minutes and 24 seconds.

Error informational display table

card.
E5 K Temp. Over| Inner core temperature too high lead to shut down
E6 Heat Fail| Heating failed.
E7 Tip Over| Dumping alarm when machine is tilted at less than 45 degrees.

machine stop working when tilt alarm starts.

Setting interface：
Press “MENU” to enter the Setting interface, press the “MENU” button to enter different

and can send out DMX signal when it’s address is “1++”.
Wireless Control| ON/OFF| Wireless function switch. you can match codeWhen shows “ON”
Manual Fountain| ON/OFF| Manual fountain switch , for testing purposes only.
Auto Clear Delay| 0.1-0.9s| Automatic clear material settings.

Advanced menu：
Use: Page-5/8 Press “MENU” 3 seconds to enter the advanced setup interface, press MENU key to enter different options, press MENU till 3 seconds to return to the main interface.

User Mode

| Factory Mode is factory debugging mode, User

Mode is using mode

Tip Over Error| ON/OFF| Tilt function switch.
Default Parameter| | Press “ENTER” to restore all parameters to the

factory settings.

Power cable connection：

• For convenient use, there are power supply cable and power supply ex-cable. power Supply ex-cable can achieve multiple devices connected, maximum cascade is 6pcs. All power plugs are industrial plug with lock, it need to toggle snap and rotate when using.
• If you use mobile power plate, be sure to use good quality and match rated power products. 6 pcs machines requires around 2000 watts, cores should be over 1.5 square.

Wireless remote control mode：

• If the remote control cannot work, please check whether wireless function was turn on. Press MENU to switch to wireless control setting , menu is set to “ON” , press “ENTER”. This interface can also be mactching code with remote controller.
• Sparkular mini can controlled by both DMX and remote controller, when there are DMX signal input, wireless remote controller will not work.
• When using remote control you need to pull out the antenna

Responsibility Excellence Innovation

1 ON

|

Address “1” ON

|

1 OFF

|

Address “1” OFF

---|---|---|---
2 ON| Address “3” ON| 1 OFF| Address “3” OFF
3 ON| Address “5” ON| 1 OFF| Address “5” OFF
SET| When use different remote control| CLEAR| Automatically clean

material for 3 seconds

5 S| All Starts 5 seconds| 15 S| All starts 15 seconds

30 S

| All Starts 30 seconds|

OFF

|

All stop

Attention

• The first group machines correspond to DMX address “1”, the second group DMX addressis “3”, the third DMX address is “5”, remote controller controls 3 group machines. It also can set all Sparkular mini address as “1”.
• When the lamp is not lit or become weak on the remote controller, replace the battery. It is better to take battery out when transporting to prevent consumption of battery power by unmeant press of button.

Battery model： 12V 23A

• When the machine is occasionally not working, may be caused by interference, pleasepress the start button again.
• Wireless control is easy influenced by interference, it is suggest to stay as close to machine as possible when use remote controller, and machines cannot use metal shielding

Wireless host Sparkular mini mode (requires communication cables):

In occasion of strong interference, using the wireless host can avoid interference, and ensure stable control. Set the first unit of Sparkular mini DMX address into “1++”, this machine address is “1”, but it can also output DMX signal and turns into wireless host Sparkular mini. Use communication cables to connect all the Sparkular mini, the host Sparkular mini will receive the signal from remote controller and transfer to all other Sparkular mini via a communication cable to realize stable signal transmission.

Cable DMX mode：
When using the DMX controller, the system takes 2 channels

Warranty instructions

• Sincere thanks for your choosing our products, you will receive quality service from us.
• The product warranty period is one year, If there is any quality problems, we can exchange brand new same model machine to you within seven days after receive the product.
• We will offer free of charge maintenance service for machines which with hardware malfunction (except for the instrument damage caused by human factors) in warranty period. Please don’t repair machine without factory permission

Below situation NOT included in warranty service

1. Damage caused by improper transportation, using, management, and maintenance, or damage caused by human factors;
2. Disassemble, modified or maintain products without Showven’s permission;
3. Damage caused by external reasons (lightning strike, power supply etc);
4. Damage caused by improper installation or use; For product damage not included in warranty range, we can provide paid service. Invoice and warranty card are necessary when asking for service from SHOWN.
   Product Name：| | Serial NO.：|
   ---|---|---|---
   Purchase Date:|
   Contact Number:|
   Address:|

   ---

Customer Feedback Information:

|
Actual malfunction:|
Maintenance details:|
Maintenance person:| | Maintenance Date:|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>