SHOWVEN Sparkular Triple 3-Way Nozzle Cold Spark Machine User Manual

SHOWVEN Sparkular Triple 3-Way Nozzle Cold Spark Machine

Safety Considerations

• Never touch the nozzle of SPARKULAR TRIPLE, danger of getting burnt.
• Never touch the sparks which shooting out from the nozzle.
• Cover of nozzle of SPARKULAR TRIPLE is prohibited.
• Keep audience, animals or flammable objects at a minimum distance of 3m (for front and rear side) and 5m (for left and right side) from SPARKULAR TRIPLE. Make sure sparks shoot out from SPARKU-LAR TRIPLE can NOT touch any objects in the air.
• Ensure that children, animals and unauthorized persons don’t have access to the SPARKULAR TRIPLE!
• Unauthorized repair are prohibited, it may cause serious incident.
• Keep SPARKULAR TRIPLE dry and do NOT use in rain or snow.
• Make sure lid of feeding hopper are well covered when use SPARKULAR TRIPLE. Accidentally burn-ing of Composite Ti can only use sands to extinguish. Composite Ti should keep away from moisture and stored in a dry sealed environment.
• Clear material is necessary both before and after the show. Please check nozzle of SPARKULAR TRIPLE after each show, if there are consumable agglomerated in the nozzle, please clear it with screwdriver, otherwise it will affect the sparks effects and even damage the machine.
• Maximum cascade of SPARKULAR TRIPLE is 2 units with one standard power cable. Otherwise it may damage the machine and even cause fire.
• For better heat dissipation, block the air intake and air outlet is prohibited.

Model: BT51/BT52

| Parameters
Dimension| 400×290×270mm
Weight| 20kg
Input| BT51:AC200-240V, 50/60Hz BT52:AC100-120V, 50/60Hz
Work power| 1500w
Working Temperature| -10℃~ 50 ℃
Casing| Metal
Effect height| 2.0-4.0m adjustable (HC8200 MEDIUM) 2.0-5.0m adjustable (HC8200 LARGE)
Hopper capacity| 160g 3
HC8200 consumption| 17g/min 3

Feature

• Triple heads, multi effect
• Each nozzle can be controlled separately
• Faster response, stronger bursts
• RDMX function, status can be monitored by original host controller

Operation Panel

LED display area:

READY1, READY2, READY3 shows the status of 3 heads respectively; After turn on, the machine pre-heating automatically, pre-heating time is around 5min. When “READY” turns from flashing into long on, indicates that the machine is ready to work. DMX: Flashing shows that DMX signal is connected, otherwise is without signal

Control button area

• MENU: Short press to switch interface, press for 3 seconds can switch to the advanced setup interface.
• DOWN: Parameters down
• UP: Parameters up
• ENTER: Confirm and save parameters

Radio frequency identification area

Please note that granules RFID card can increase the single machine specific working time. The card is disposable, can only use once.

Interface

Main Interface:

First line: temp. and error info. of each nozzle of machine Left shows nozzle 3, middle shows nozzle 2, right show nozzle 1. Second line: shows DMX address, and remaining working time 10min 22seconds

Error information

high
E4 Time Remain| Insufficient granules or remaining time, please swiping RFID card.
E5 K Temp. Over| Machine stops working due to the inner core temperature is too high
E6 Heat Fail| Heating failed.

Setting interface
Press “MENU” to enter the Setting interface, press the “MENU” button to enter different options until you return to the main interface.

purpose only.

Advanced menu

Press “MENU” 3 seconds to enter the advanced setup interface, press MENU key to enter different options, wait 3 seconds to return to the main interface.

default value without engineer’s suggestion from SHOWVEN.

Auto Heat| ON/OFF| Auto preheat function switch after turning on

machine

Density| 70-100| Adjust the sparks density. Please don’t change default

value without engineer’s suggestion from SHOWVEN.

Mode Selection| Factory Mode/

User Mode

| Factory Mode is factory debugging mode, User

Mode is using mode

Default Parameter

Mode

| | Press “ENTER” to restore all parameters to the factory

settings.

Standby Switch| On/Off| When it’s on, the machine can only generate spark when pre-heating finish.

When using the DMX controller, the system takes 6 channels, each nozzle takes 2 channels.

Please set DMX address following the below rules when connecting with the SHOWVEN host controller.

Note: Wrong DMX address setting may cause uncontrolled shooting of SPARKULAR TRIPLE.

Warranty instructions

• Sincere thanks for your choosing our products, you will receive quality service from us.
• The product warranty period is one year, If there is any quality problems, we can exchange brand new same model machine to you within seven days after receiving the product.
• We will offer free of charge maintenance service for machines which with hardware malfunction (except for the instrument damage caused by human factors) in the warranty period. Please don’t repair the machine without factory permission.

Below situation NOT included in warranty service:

1. Damage caused by improper transportation, using, management, and maintenance, or damage caused by human factors;
2. Disassemble, modified or maintain products without Showven’s permission;
3. Damage caused by external reasons (lightning strike, power supply etc);
4. Damage caused by improper installation or use; For product damage not included in the warranty range, we can provide paid service. An invoice and warranty card are necessary when asking for service from SHOWN

Warranty card

Product Name:| | Serial NO.：|
---|---|---|---
Purchase Date:|
Contact Number:|
Address:|

Customer Feedback Information:

|
Actual malfunction:|
Maintenance details:|
Maintenance person:| | Maintenance Date:|

Showven Technologies Co., Ltd
Add: Building B1, Changsha E Center No.18, Xiangtai Road, Liuyang Economic Development Zone, Changsha City, 410300, Hunan Province, P.R.China.

• Tel: +86-731-83833068
• Web: www.showven.cn
• E-mail: info@showven.cn

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>