PROJECTA IG2-BT7 High Powered Management with Bluetooth Monitor Instruction Manual

June 12, 2024
Projecta

PROJECTA logo INTELLI-GRID 12V 2000/3000W
HIGH POWERED MANAGEMENT
WITH BLUETOOTH MONITOR P/No IG2-BT7, IG3-BT7

SYSTEM INTRODUCTION

The IG2/3-BT7 is a 2000W/3000W power solution for all your power, lighting and water requirements. This system monitors the status of the tyres and the level of the RV while also tracking the gas cylinders. It is connected to a color display with Bluetooth, so  you can check and control the system from your phone.

SYSTEM COMPONENTS

  • 7” Monitor with App
  • 2KW/3KW Inverter/Charger with AC change over swtich
  • MPPT Solar controller
  • DC-DC Charger
  • Controller Box
  • Constant Output Module with 12 outputs
  • Auxiliaries Controller with 9 outputs & Water Tank Measurement
  • Lights Module with 6 outputs
  • 200Ah/400Ah Lithium Battery
  • Wireless Switch (Not supplied)
  • 4 Water tank sensors (Not supplied)

PAB – FRONT: 950 x 370 x 160mm

PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
FRONT

PAB – BACK

KEY FEATURES

INVERTER & GRID POWER
2000/3000W inverter with 120/180Amp charging, grid power booster and AC transfer switch.
AS/NZS 3001 ready
LITHIUM BATTERY
An advanced and powerful 200/400Ah lithium battery perfectly matched to the Intelli-Grid system provides the ultimate power for off gird requirements
BLUETOOTH MONITOR
Bluetooth 7” Colour monitor showing SOC, full control of the RV, its water, lighting and hardware
MULTIPLE CHARGING OPTIONS
30/60A DC-DC charging and 40A MPPT solar charging for charging from vehicle or when sun is shining
SOLAR CHARGING WAKING UP
When this feature is set to enable, the system can wake up and be solar charged automatically as long as the sun is shining even when the system is OFF
LOW VOLTAGE PROTECTION
Multiple strategies for low voltage protection of service batteries to avoid failure of lithium batteries by over-discharge

MONITORING THE 7” COLOUR DISPLAY INTRODUCTION

PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - Home
Page

The above is the home page, the details are as follows:

  1. Region 1: Area for time and date display.

  2. Region 2: Indoor and Outdoor temperature display area.

  3. Region 3: Area for showing battery information.
    In this area, the user can see the battery power data and status. It contains the following points:
    a) Check the batteries are charging or discharging.
    b) Check the batteries voltage and current.
    c) Check the batteries SOC value.
    d) Check the time to go or time to full of batteries.

  4. Region 4: Area of shortcut keys.
    a) PWR: All DC and AC outputs turned on/off with this key. Only the constant live output of IGCMD and the class C3 output of C12 are retained.
    b) Inverter: Inverter charger ON/OFF switch.
    c) HWS: Water heater ON/OFF switch.
    d) Pump: Water pump ON/OFF switch.

  5. Region 5: Water tank level display area.
    a) If the fresh water is lower than the warning value, the alarm is triggered.
    b) If the gray or black water is greater than the warning value, the alarm is triggered.

  6. Region 6: Scene mode.
    a) ECO mode: System will enter “ECO” Mode automatically after being started. When SOC drops to 15% (it is settable within 15% – 20%), the system shuts down the inverter outputs and the heavy loads, keeping ONLY the essential loads on.
    i. Typically fridge, ceiling light and a spare output is ON. Only the constant live output of IGCMD are ON, such as Fridge and USB.
    ii. Pump, spot FR&BK, bedroom light can be turned ON manually.
    iii. One group of the C12 outputs (marked as C3) is ON.
    When SOC is back to 15% (or other setting value) + 3% or there is AC grid charging, system exits ECO mode automatically. Customer can also exit the mode manually
    b) Night mode: Designed for a silent environment for customers. It can be activated at the front page of 7” screen. When entering the mode,
    i. The system will shut down the lights and the back lights of the screens.
    ii. De-rate the charging current of inverter/charger to reduce the fan noise.
    c) Light off: This mode is designed for turning off the all lights with one key.

  7. Region 7: Gas level display area.

  8. Region 8: Charging source information display area.
    In this area, the user can check the charging data as follows:
    PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - Charging
source a) Inverter/Charger:
    i. Display output voltage, power and load rate.
    ii. The user can select the AC input source.
    “Mains” means the source is grid, “Gen” means it is generator.
    b) Vehicle charger: Checks the output current and power of vehicle charger.
    c) Solar charger: Checks the output current and power of vehicle charger

  9. Region 9: Navigation area.
    Note:
    a) The icon will turn white when switched to the corresponding page.
    b) When the alarm icon is red, it means that one or more alarms exist. After the alarm is removed, the icon turns to gray.
    PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - Navigation
area

Load Control Page

PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - Load
Control Page The load control page displays all switchable outputs with their functions named. When the load is turned on, the load icon is white with a green dot in the upper right corner. If the load is turned off, the icon turns gray and the green dot disappears.

Sensor Page
6 .3.1 Leveling
Ensures your RV is level when parked.PROJECTA IG2 BT7 High Powered
Management with Bluetooth Monitor - Leveling 6 .3.2 TPMS
Monitors tyre pressure to prevent premature wear with high / low warning setting.PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
TPMS6 .3.3 GAS sensor
Monitors the level of gas available within the gas cylinders.PROJECTA IG2
BT7 High Powered Management with Bluetooth Monitor - GAS
sensor

Setting Page

The setting menu allows the user to make basic changes to the system, including:

  1. Screen setting.
    The user can set screen brightness level, time and date, sleep time, buzzer enable, temperature unit and language selection.
    PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - Screen
setting

  2. Rename.
    In this page, the load and water tank can be renamed.
    PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
RenameFurther, the icon also can be changed when renaming the load.
    PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
load

  3. System.
    The user can engage the ‘Solar Automatic Wake Up Function’ as well as disengage the ‘Ground Relay’.
    WARNING: Ground relay MUST be left on for correct RCD operation.
    PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
System

  4. Firmware.
    Displays all software revisions of available components.
    PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
Firmware

  5. QR code information.
    After running the app, users can directly scan the QR code to log in without entering the user name and password.
    PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - QR code
information

System Updating

PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - System
Updating

This system can be upgraded via a USB stick. First, copy the files that need to be updated to a USB stick and place them all in a folder named IDM. Insert the USB stick into the U disk port located on the back of 7” screen. The upgrade dialogue box will pop up on  the 7” screen as shown right.
The ‘Screen’ selection refers to updating the  7” display files while ‘Device’ refers to system components such as IGCMD, IGCOM, etc. After selecting the correct update action, update each piece of software, one at a time. Power must not be turned off or removed  from the system during update process.
The latest software will be available at www.projecta.com.au

Data Analysis

In Region 3 and Region 8 on the main display, double click the corresponding icon to enter the data analysis page. The screen can display the history data of multiple devices in the system.

  1. Battery
    PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - Data
Analysis

  2. Vehicle Charger
    PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - Vehicle
Charger

  3. Solar
    PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
Solar

  4. Inverter Charger
    PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - Inverter
Charger

COMPONENT SPECIFICATIONS

INVCHR2 & INVCHR3
2000W/3000W 12V INVERTER/CHARGER
Perfect for powering the most demanding 240V appliances on the go this inverter/charger is ideal for operating on or off the grid. An RCD is included to ensure maximum safety for the unit and operator.
The inverter/charger is fitted with grid power boost which is great if the shore power or generator is weak.
Grid power boost will supplement the shore power to ensure all your appliance can run.

SPECIFICATIONS

PART NO                                              INVCHR2| INVCHR3
240V CHARGING|
CHARGE TYPE| 5 Stage Automatic
INPUT| 240VAC, 50/60Hz, 32A(MAX)
OUTPUT| 12V, 120A| 12V, 180A
BATTERIES SUPPORTED| GEL, AGM, WET, Lithium
TEMPERATURE COMPENSATION| YES
INVERTER|
INPUT| 12V (10.5V~17V)
OUTPUT| 220/230/240 VAC
FREQUENCY| 50/60 Hz
OUTPUT POWER| 2000W (4000W peak)| 3000W (6000W peak)
GRID BOOST OUPUT| 24Amps, Mains Supply
+ 8.3Amps Inverter RCBO limited to 16Amps max.| 28Amps, Mains Supply + 12.5Amps Inverter RCBO limited to 16Amps max.
AC TRANSFER| <2m Sec
OPERATING TEMPERATURE| -20°C ~ 65°C
WEIGHT| 17KG| 21KG
IP RATING| IP20

PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
TERMINAL SIGNAL TERMINAL INTRODUCTION

NO. LABEL DEFINITION
1 Bat Sample Battery temperature and voltage sample.
2 Remote A dry contact input for remote on/off, often IGN was connected.
3 Com MON RS485 port for external monitor such as INVCHRD-BT.
4 Com Sync Communication with PROJECTA’s LB-HD series lithium battery, which

is able to synchronize lithium battery’s charging and discharging strategy
5| Relay1| Dry contact output control 1(NO,C,NC)
(NO,C,NC)
6| Relay2| Dry contact output control 2(NO,C,NC)
(NO,C,NC)
7| S+| Slave charger for starter battery

SC540
5 STAGE MPPT SOLAR CHARGER CONTROLLER WITH 100V INPUT
Get the most out of your solar array using these Maximum Power Point Tracking (MPPT) solar controllers increasing the charging output by up to 30% (compared to PWM Solar controllers).PROJECTA IG2 BT7 High Powered Management with
Bluetooth Monitor - SC540

SPECIFICATIONS

PART NO| SC540
BATTERY VOLTAGE| 12/24/48V
MAXIMUM SOLAR VOLTAGE| 100V
STANDBY CURRENT| 1mA 12V
CHARGER TYPE| 5 Stage
INPUT| 100V
CONTROL TYPE| MPPT
BATTERIES SUPPORTED| GEL, AGM, WET, Lithium
TEMPERATURE COMPENSATION| Yes
COMMUNICATION| RS485
STORAGE TEMPERATURE| -40°C ~ 70°C
HUMIDITY| 5 – 95%
IP RATING| IP31
WEIGHT| 1.4KG
COOLING| Convection

PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - Connection
terminal

LABEL DEFINITION

PV| +| Connection terminal for PV array Positive
–| Connection terminal for PV array Negative
BAT| +| Connection terminal for Battery Positive
–| Connection terminal for Battery Negative
EPO| EPO contacts, defined for remote on/off.
NC| Output dry contacts.
C
NO
RS485| Connection terminal for RS485 communication.
Temp. Sensor| Connection terminal for battery temperature sensor.

PIN DEFINITION OF TEMP SENSOR

PIN DEFINITION
Pin 1 Battery Positive
Pin 2 Battery Negative
Pin 3 Temperature sensor
Pin 4 Battery Negative

PIN DEFINITION OF RS485 COMMUNICATION PORT

PIN DEFINITION
Pin 1
Pin 2
Pin 3 RS485_A
Pin 4
Pin 5
Pin 6 RS485_B
Pin 7
Pin 8

PMDCS30
DC-DC 12V CHARGER
Smart DC to DC chargers specifically designed for Intelli-RV and Intelli- Grid.PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
PMDCS30 SPECIFICATIONS

PART NO PMDCS30
CHARGER TYPE 5 Stage
ALTERNATOR INPUT VOLTAGE 12–16V
OUTPUT 12V, <30A
BATTERIES SUPPORTED GEL, AGM, WET, Lithium
STORAGE TEMPERATURE -40°C ~ 70°C
OPERATING TEMPERATURE -40°C ~ 70°C
IP RATING IP20
WEIGHT 1.0KG
COOLING Convection
SMART ALTERNATOR Turn on: 12.2V Turn off: 11.9V
CONVENTIONAL Turn on: 13.2V Turn off: 12.8V

CONNECTORS AND TERMINALS

Connectors and terminals guide

No.| Print| PMDCS30| Remarks| Circuit colours and labelling
---|---|---|---|---
1| Alternator| Connects to positive of Alternator| Connects to positive battery post| Red + Label “Aux+”
BAT-| Connects to negative of Alternator| Connects to negative battery post| Black – Label “Aux-”
2| AUX BAT| Connects to positive of auxiliary battery| | Red + Label “Vehicle Batt+”
BAT-| Connects to negative and negative of auxiliary battery| | Black – Label “Vehicle Batt-”
3| COM| For communication of RS485| Not Connected|
4| 1| Not used| Details of setting can be found as Chapter 4.6|
2| Set on for 30Amp, off for 15Amps
3| Used to set battery chemistry
4
5| BAT-| Connects to BTS’ black cable| For battery temperature sensing| RED Ring Terminal connect to Battery +ve
Temp| Connects to BTS’ white cable
V-Sen| Connects to BTS’ red cable| For voltage sensing

Fuse specification

No.| Print| Specification| Colour| Quantity| Protection for
---|---|---|---|---|---
6| Alternator| 30A/32VDC for PMDCS30| Amber| 2| Input from alternator
7| AUX BAT| 20A/32VDC| Yellow| 2| Output to charge auxiliary battery

IGCMD
INTELLI-GRID AUXILIARIES CONTROLLER
This is the input and output controller, with water sensors and switchable devices being connected with built in fused outputs.PROJECTA IG2 BT7 High
Powered Management with Bluetooth Monitor - IGCMD

SPECIFICATIONS

PART NO| IGCMD
INPUT VOLTAGE| 9~32V
INPUT CURRENT| <60A
OUTPUTS| 2 x 15A Relay with Bypass, 7 x 15A Relay, 4 x Dry contact
INPUTS| 4 x Dry contact, 4 x conductive water measurement
COMMUNICATION| CAN bus, RS485, RF
OUTPUT

A5-1| A5-2| A5-3| A5-4| A5-5| A1-1
A1-2| GND| GND| GND| GND| A5-6
GND| GND| GND| GND| GND| A5-7
OUTPUTS| FUSE| OUTPUT LABEL| DEVICES
---|---|---|---
A5-6 (15A)| A5-6 (15A)| Spare 1|
A5-7 (15A)| A5-7 (15A)| Spare 2|
A5-1 (15A)| A5-1 (15A)| Spare 3|
A5-2 (15A)| A5-2 (15A)| Media| TV & Stereo &
A5-3 (15A)| A5-3 (15A)| Fans & 12V| Fan & USB, 12 Sockets
A5-4 (15A)| A5-4 (15A)| HWS| Hot water service
A5-5 (15A)| A5-5 (15A)| Heater| Diesel heater if fitted
A1-1 (15A) With optional Bypass fuse| A1-1 (15A)| PUMP 1| Pump 1
A1-2 (15A) With optional Bypass fuse| A1-2 (15A)| PUMP 2| Pump 2
Water Sensor 1| | Tap 1| Tank 1
Water Sensor 2| | Tap 2| Tank 2
Water Sensor 3
Water Sensor 4| | Waste| Tank 3

PMWLM6
6 CHANNEL OUTPUT MODULE
This 6 channel output module works with wireless switches and can also be controlled via the 4”, 7” screen or phone app.

SPECIFICATIONS

PART NO| PMWLM6
INPUT VOLTAGE| 9~16V
MAXIMUM INPUT CURRENT| <60A
STANDBY CURRENT DRAW| 3mA
OUTPUTS| 6 x 15A Relay
WORKING TEMPERATURE| -40°C ~ 80°C
IP RATING| IP20

PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - CHANNEL
OUTPUT MODULECONNECTORS AND TERMINALS
POWER INPUT TERMINAL DEFINITION

PIN NO| PIN DEFINITION| POLARITY| VOLTAGE RANGE| RATED CURRENT
---|---|---|---|---
1| BAT+| BAT+| 9–16V| 30A
2| BAT+| BAT+| 9–16V| 30A
3| BAT-| BAT-| |
4| BAT-| BAT-| |

OUTPUT TERMINAL DEFINITION

OUTPUT

L1| L2| L3| L4| L5
GND| GND| GND| GND| L6
GND| GND| GND| GND| GND

PIN DIAGRAM

PIN NO| PIN DEFINITION| FUSE| CURRENT RANGE| VOLTAGE RANGE
---|---|---|---|---
1| L1| L1 15A| 0–10A| 0-16V
2| GND| | 0–15A| 0-16V
3| GND| | 0–15A| 0-16V
4| L2| L2 15A| 0–15A| 0-16V
5| GND| | 0–15A| 0-16V
6| GND| | 0–15A| 0-16V
7| L3| L3 15A| 0–15A| 0-16V
8| GND| | 0–15A| 0-16V
9| GND| | 0–15A| 0-16V
10| L4| L4 15A| 0–15A| 0-16V
11| GND| | 0–15A| 0-16V
12| GND| | 0–15A| 0-16V
13| L5| L5 15A| 0–15A| 0-16V
14| L6| L6 15A| 0–15A| 0-16V
15| GND| | 0–15A| 0-16V

IGCOM12
12 WAY FUSED OUTPUT MODULE
Provides a constant 12V power to power loads like range hoods, fridges, memory retentive circuits and other lighting.
IGCOM12 has built in low voltage disconnect and inhibit functions on selected outputs.PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
IGCOM12

SPECIFICATIONS

PART NO| IGCOM12
NOMINAL VOLTAGE| 12V
MAX INPUT CURRENT| 80A
OUTPUTS| 6 x 30A

6 x 15A

WEIGHT| 780g
WORKING TEMPERATURE| -40°C ~ 65°C
IP RATING| IP20

PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
FUSED POWER INPUT TERMINAL DEFINITION

PIN NO| PIN DEFINITION| POLARITY| VOLTAGE RANGE| RATED CURRENT
---|---|---|---|---
1| BAT+| BAT+| 9–16V| 40A
2| BAT+| BAT+| 9–16V| 40A
3| BAT-| BAT-| |
4| BAT-| BAT-| |

OUTPUT TERMINAL DEFINITION

OUTPUT

C3-1| C3-2A| C3-2B| C3-3A| C3-3B| C3-4
C2-4| C2-2A| C2-1A| OUT4A| OUT3A| OUT1
C2-3| C2-2B| C2-1B| OUT4B| OUT3B| OUT2

PIN DIAGRAM

PIN DIAGRAM

PIN NO| PIN DEFINITION| FUSE| CURRENT RANGE| VOLTAGE RANGE| FUNCTION| EXAMPLE DEVICE
---|---|---|---|---|---|---
1| C2-1A| F1 30A| 0–15A| 9–16V| Inhibit and LVD| Slide out
2| C2-1B| F1 30A| 0–15A| 9–16V| Inhibit and LVD| Awning
3| C2-2A| F2 30A| 0–15A| 9–16V| Inhibit and LVD| Steps
4| C2-2B| F2 30A| 0–15A| 9–16V| Inhibit and LVD|
5| C2-3| F3 15A| 0–15A| 9–16V| Inhibit and LVD|
6| C2-4| F4 15A| 0–15A| 9–16V| Inhibit and LVD|
7| C3-1| F5 15A| 0–15A| 9–16V| Always On| Outside compressor fridge
8| C3-2A| F6 30A| 0–15A| 9–16V| Always On| Inside compressor fridge
9| C3-2B| F6 30A| 0–15A| 9–16V| Always On|
10| C3-3A| F7 30A| 0–15A| 9–16V| Always On| Range hood
11| C3-3B| F7 30A| 0–15A| 9–16V| Always On|
12| C3-4| F8 15A| 0–15A| 9–16V| Always On|
13| OUT1| F9 15A| 0–15A| 9–16V| Inhibit and LVD| See Note 1 below
14| OUT2| F10 15A| 0–15A| 9–16V| Inhibit and LVD
15| OUT3A| F11 30A| 0–15A| 9–16V| Inhibit and LVD
16| OUT3B| F11 30A| 0–15A| 9–16V| Inhibit and LVD
17| OUT4A| F12 30A| 0–15A| 9–16V| Inhibit and LVD
18| OUT4B| F12 30A| 0–15A| 9–16V| Inhibit and LVD

Note 1: This group can be configured by Dipswitch.
Dip 1 ON: Run Inhibit function & LVD
Dip 2 ON: Always on
Dip 1&2 OFF: Outputs off

The Dipswitch comes default as per the above table and shown right.

IGCOM
INTELLI-GRID CONTROLLER
This is the brains of the INTELLI-Grid system. Controlling communications to external sensors and devices and shutting down power on non essential loads when the battery power gets low.

SPECIFICATIONS

PART NO| IGCOM
INPUT| 12V
WORING CURRENT| 80mA
STANDBY CURRENT| 5mA
COMMUNICATION| CAN bus, RS485 Bluetooth
WORKING TEMPERATURE| -25°C ~ 60°C
STORAGE TEMPERATURE| -30°C ~ 85°C
WEIGHT| 200g
IP RATING| IP20

PMTPMS
TYRE PRESSURE MONITORING SYSTEM MODULE
The Tyre Pressure Monitoring System (TPMS) monitors the RVs tyre pressure before and during the journey.PROJECTA IG2 BT7 High Powered Management with
Bluetooth Monitor - PMTPMS SPECIFICATIONS

PART NO PMTPMS x 4 (one for each tyre)
PART NO Receiver-PMTPMS-R
INPUT 6-24V
WORING CURRENT 30mA
WORKING TEMPERATURE -40°C ~ 85°C
HUMIDITY <95%
RECEIVING FREQUENCY 433.910Mhz
WIRED COMMUNICATION RS485
WEIGHT 150g
PART NO Sender * 4 -PMTPMS-S
WORING VOLTAGE 2.2 ~ 3.6V
BATTERY TYPE CR1632
TRANSMITTED CURRENT <5mA
TRANSMITTED POWER <5dbm
TRANSMITTED FREQUENCY 433.910Mhz
PRESSURE RANGE 14~ 130PSI
ACCURACY ± 1.45 PSI
WORKING TEMPERATURE -30°C ~ 70°C
WEIGHT 13.8g

PMLVL
LEVELLING SENSOR
Level the RV with the levelling sensor which can be monitored via the phone app.
Calibration
To calibrate the level sensor, the RV needs to be level in both forward and back and side to side. Once level, go to the Setting Page, select Level Sensor and press Calibrate. This will zero the sensor.

SPECIFICATIONS

PART NO| PMLVL
WORKING VOLTAGE| 9~16V
WORING CURRENT| 30mA
WORKING TEMPERATURE| -40°C ~ 85°C
IP RATING| IP20
ACCURACY| ±2°

INSTRUCTIONS ON HOW TO PAIR THE GAS SENSORS

Enable the GAS Feature.
Go to the Setting Page.. Find the Sensors Page and enable it. Paring the Sensors.
Long press the “SYNC” button on the gas sensor until a value is displayed on the GAS.


PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - Gas
2| PROJECTA IG2 BT7 High
Powered Management with Bluetooth Monitor - gas sensor 2
Repeat the process to pair second gas sensor.

IGD-BT7
7” COLOUR BLUETOOTH MONITOR
The 7” colour display, enables complete control of the RV or commercial application. Its smart, intuitive design provides all the vital information at the press of a button.

SPECIFICATIONS

PART NO| IGD-BT7
WORKING VOLTAGE| 12V
WORKING CURRENT| 350mA Screen ON, 200mA Screen OFF
RESOLUTION| 1024 x 600
COMMUNICATION| RS485.CAN.Bluetooth
WORKING TEMPERATURE| -30°C ~ 70°C
STORAGE TEMPERATURE| -30°C ~ 85°C
WEIGHT| 200g
IP RATING| IP 20

BATTERIES

LB200-HDJ
12V HIGH DISCHARGE 200AH LITHIUM BATTERY
LB200-HD boast impressive capabilities and are ideal for 4WDs and caravans with high power demands.

SPECIFICATIONS

PART NO| LB200-HD
NOMINAL VOLTAGE| 12.8V
NOMINAL CAPACITY| 200Ah
NOMINAL ENERGY| 2560Wh
CHARGE VOLTAGE| 14.2V
DISCHARGE CUT-OFF VOLTAGE| 11.2V
STANDARD CHARGE CURRENT| 100 Amps
MAXIMUM CHARGE CURRENT| 200 Amps
MAXIMUM DISCHARGE CURRENT| 200 Amps
PEAK DISCHARGE CURRENT| 300 Amps (10Mins)
OPERATING TEMPERATURE| -20°C ~ 60°C
MAXIMUM NUMBER OF BATTERIES IN PARALLEL| 4
NUMBER OF DISCHARGE CYCLES| 3000
WEIGHT| 22KG
IP RATING| IP20

LB400-HDJ
12V HIGH DISCHARGE 400AH LITHIUM BATTERY
The LB400-HD boasts an astonishing 400Ah capacity and a market leading 300A discharge capability making it ideal to partner with high current drawing appliances such as 3000W inverters.

SPECIFICATIONS

PART NO| LB400-HD
NOMINAL VOLTAGE| 12.8V
NOMINAL CAPACITY| 400Ah
NOMINAL ENERGY| 5120Wh
CHARGE VOLTAGE| 14.2V
DISCHARGE CUT-OFF VOLTAGE| 11.2V
STANDARD CHARGE CURRENT| 100 Amps
MAXIMUM CHARGE CURRENT| 200 Amps
MAXIMUM DISCHARGE CURRENT| 200 Amps
PEAK DISCHARGE CURRENT| 300 Amps (10Mins)
OPERATING TEMPERATURE| -20°C ~ 60°C
MAXIMUM NUMBER OF BATTERIES IN PARALLEL| 4
NUMBER OF DISCHARGE CYCLES| 3000
WEIGHT| 42.5KG
IP RATING| IP20

PMWSW4
Wireless switches make it easy to install additional switches if required. i.e. additional bedroom switch is easy as 2 screws for installation.
For programming please contact our customer service.

SPECIFICATIONS

PART NO| PMWSW4
RATED VOLTAGE| 5V
BATTERY TYPE| 2 x CR2032
COMMUNICATION| RF 433Mhz
EFFECTIVE RANGE| Outdoor 30m, Indoor 15m
IP RATING| IP20
WORKING TEMPERATURE| -20°C ~ 60°C
MOUNTING| Surface
WEIGHT| 40g

WATER TANK PROBE
For Intelli-Grid system, a maximum of 4 probes can be monitored.
Note: Always check the probe required for the water tank before pruchase. There are 2 probe styles. PMWS200

  • Side installation
  • Suitable for water tank
  • Depth >200mm

PMWS400

  • Side installation
  • Suitable for water tank
  • Depth <400mm

STRUCTURE AND INSTALLATION

Monitor

PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
Monitor Inverter

Note: Please install the inverter in a well ventilated area so that it works at maximum efficiency.

Water Probe
PMWS400 WATER TANK PROBEPROJECTA IG2 BT7 High Powered Management with
Bluetooth Monitor - Water Probe PMWS200 WATER TANK PROBEPROJECTA IG2 BT7
High Powered Management with Bluetooth Monitor - TANK PROBE
2

INTELLI-GRID-BT7

PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor - INTELLI-
GRID-BT7PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
INTELLI-GRID-BT7 2PROJECTA IG2 BT7 High Powered Management with Bluetooth Monitor -
INTELLI-GRID-BT7 3

WARRANTY STATEMENT

Applicable only to product sold in Australia
Brown & Watson International Pty Ltd of 1500 Ferntree Gully Road, Knoxfield, Vic., telephone (03) 9730 6000, fax (03) 9730 6050, warrants that all products described in its current catalogue (save and except for all bulbs and lenses whether made of glass or  some other substance) will under normal use and service be free of failures in material and workmanship for a period of two (2) years (unless this period has been extended as indicated elsewhere) from the date of the original purchase by the consumer as  marked on the invoice.
This warranty does not cover ordinary wear and tear, abuse, alteration of products or damage caused by the consumer. Projecta solar panels are covered by a 1 year warranty for materials and workmanship and a 20 year warranty for at least 80% power output.
To make a warranty claim the consumer must deliver the product at their cost to the original place of purchase or to any other place which may be nominated by either BWI or the retailer from where the product was bought in order that a warranty assessment  may be performed. The consumer must also deliver the original invoice evidencing the date and place of purchase together with an explanation in writing as to the nature of the claim.
In the event that the claim is determined to be for a minor failure of the product then BWI reserves the right to repair or replace it at its discretion. In the event that a major failure is determined the consumer will be entitled to a replacement or a refund as well  as compensation for any other reasonably foreseeable loss or damage.
This warranty is in addition to any other rights or remedies that the consumer may have under State or Federal legislation.
IMPORTANT NOTE
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have  the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Distributed by
AUSTRALIA
Brown & Watson International Pty. Ltd.
Knoxfield Victoria 3180
Phone: (03) 9730 6000
Fax: (03) 9730 6050
National Toll Free: 1800 113 443
NEW ZEALAND OFFICE
Griffiths Equipment Ltd.
19 Bell Avenue,
Mount Wellington,
Auckland 1060, New Zealand
Phone: (09) 525 4575 PROJECTA logoIS537
Issue 1: 17/03/2023

Documents / Resources

| PROJECTA IG2-BT7 High Powered Management with Bluetooth Monitor [pdf] Instruction Manual
IG2-BT7 High Powered Management with Bluetooth Monitor, IG2-BT7, High Powered Management with Bluetooth Monitor, Powered Management with Bluetooth Monitor, Management with Bluetooth Monitor, Bluetooth Monitor, Monitor
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals