PROJECTA PMSHUNT Intelli-Rv 500amp Shunt Module Instruction Manual
- June 9, 2024
- Projecta
Table of Contents
PROJECTA PMSHUNT Intelli-Rv 500amp Shunt Module
INSTALLATION GUIDE
WARNING: Please read this document very carefully to avoid battery
monitor malfunction or fire hazards.
The active shunt must be located in a dry environment.
MOUNTING THE MODULE
Do not use mounting screws with countersunk heads.
WARNING
- The shunt must always be installed into the negative line.
- The battery-negative terminal may only contain one cable, which is the one going to the shunt. If there are other cables connected to this terminal as well, this may produce incorrect display readings.
- Always connect the battery negative terminal to the ‘B-’ stud of the shunt. Connecting this terminal to the ‘S-’ stud will produce incorrect display readings.
- Always disconnect the battery negative cable first before installation.
- Always connect the battery negative cable last when the installation has been completed.
INSTRUCTIONS
- The battery temperature sensor is optional and should be attached to the service battery (B1)
- Assembly sequence of nut, washers and cable lug:
STATUS LED
- GREEN: OK
- Red ON: Over current >500Amp
CONNECTION DIAGRAM FOR SINGLE BATTERY SETUP
CONNECTION DIAGRAM FOR DUAL BATTERY SETUP
SETUP VIA THE APP
SET UP VIA LCD
- Press the ‘Light’ button until the setting code is showing on the date time area which means the monitor is ready for configuration. The ‘PUMP’ button and ‘LOAD’ button can be used to scroll through the configuration menu.
PM300 + PMSHUNT WIRING DIAGRAM
PM400 + PMSHUNT WIRING DIAGRAM
WARRANTY STATEMENT
Applicable only to products sold in Australia
Brown & Watson International Pty Ltd of 1500 Ferntree Gully Road, Knoxfield,
Vic.,telephone (03) 9730 6000, fax (03) 9730 6050, warrants that all products
described in its current catalog (save and except for all bulbs and lenses
whether made of glass or some other substance) will under normal use and
service be free of failures in material and workmanship for a period of two
(2) years (unless this period has been extended as indicated elsewhere) from
the date of the original purchase
by the consumer as marked on the invoice. This warranty does not cover
ordinary wear and tear, abuse, alteration of products or damage caused by the
consumer.
To make a warranty claim the consumer must deliver the product at their cost to the original place of purchase or to any other place which may be nominated by either BWI or the retailer from where the product was bought so that a warranty assessment may be performed. The consumer must also deliver the original invoice evidencing the date and place of purchase together with an explanation in writing as to the nature of the claim.
If the claim is determined to be for a minor failure of the product then BWI reserves the right to repair or replace it at its discretion. If a major failure is determined the consumer will be entitled to a replacement or a refund as well as compensation for any other reasonably foreseeable loss or damage. This warranty is in addition to any other rights or remedies that the consumer may have under State or Federal legislation.
IMPORTANT NOTE
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law.
You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
Distributed by
- AUSTRALIA
Brown & Watson International Pty Ltd
- Knoxfield, Victoria 3180
- Telephone (03) 9730 6000
- Facsimile (03) 9730 6050
- National Toll Free 1800 113 443
- NEW ZEALAND
Narva New Zealand Ltd
- 19 Bell Avenue, Mount Wellington,
- Auckland 1060, New Zealand
- Telephone (09) 525 4575
- Facsimile (09) 579 1192
More information: https://www.caravansplus.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>