PROJECTA EVCBT2T2-3P EV Charging Cable User Manual

: June 12, 2024
: Projecta

Table of Contents

PROJECTA EVCBT2T2-3P EV Charging Cable
Product Information
Additional Information
CARE INSTRUCTIONS
SPECIFICATIONS
WARRANTY STATEMENT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PROJECTA EVCBT2T2-3P EV Charging Cable

Product Information

The EV Charging Cable (P/No. EVCBT2T2-3P) is a Type 2 to Type 2 cable suitable for charging electric vehicles with a power range of 7.2KW to 22KW. It is designed to connect the charger to the vehicle for efficient and safe charging.

Additional Information

IP Rating: Not specified in the user manual.
Impact Protection: Not specified in the user manual.
Working Temperature: Not specified in the user manual.
Working Humidity: Not specified in the user manual.
Battery Charge Times:
- 30kWh Battery: 1.5 hours
- 60kWh Battery: 3 hours
- 90kWh Battery : 4.5 hours

WARNING

For charging EV Vehicles only.
If cord is damaged do not attempt to use. It must be replaced or repaired by a
qualified person.
This lead is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

CARE INSTRUCTIONS

Try and keep clean, avoid mud and harsh chemicals.
Clean cable and connector housing with mild detergent and water.
Apply lubricated contact cleaner to the power terminals regularly.

INSTRUCTIONS FOR USE
The charge cable is suitable for Type 2 7.2~22KW vehicles and chargers.

Connect the inlet of the charging lead into the charger.
Connect the outlet of the charging lead to the car.
To stop charging. Follow the reverse procedure.

SPECIFICATIONS

PART NO.	EVCBT2T2-3P
PHASE	3
VOLTAGE	400V
CURRENT	32A
MAX POWER	22kWh
OVERALL LENGTH	5m
CABLE LENGTH	4.6m
WEIGHT	3.39kg
IP RATING	IP65
---	---
IMPACT PROTECTION	IK10
WORKING TEMPERATURE	-25°C ~ +45°C
WORKING HUMIDITY	5~95%
BATTERY CHARGE TIMES
30kWh BATTERY	1.5 hrs
60kWh BATTERY	3 hrs
90kWh BATTERY	4.5 hrs

WARRANTY STATEMENT

Brown & Watson International Pty Ltd (“BWI”) of 1500 Ferntree Gully Road, Knoxfield, Vic., telephone (03) 9730 6000, fax (03) 9730 6050, warrants that all products described in its current catalogue will under normal use and service be free of failures in material and workmanship for a period of one (1) year from the date of the original purchase by the customer as marked on the invoice. This warranty does not cover ordinary wear and tear, abuse, alteration of products or damage caused by the purchaser.
To make a warranty claim the consumer must deliver the product at their cost to the original place of purchase or to any other place which may be nominated by either BWI or the retailer from where the product was bought in order that the warranty assessment may be performed. The consumer must also deliver the original invoice evidencing the date and place of purchase together with an explanation in writing as to the nature of the claim. In the event that the claim is determined to be for a minor failure of the product then BWI reserves the right to repair or replace it at its discretion. In the event that a major failure is determined the consumer will be entitled to a replacement or a refund as well as compensation for any other reasonably foreseeable loss or damage.
This warranty is in addition to any other rights or remedies that the consumer may have under State or Federal legislation.

IMPORTANT NOTE
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Distributed by
AUSTRALIA