HOLLYLAND C1 Headset Solidcom HUB Base User Guide
- May 15, 2024
- HOLLYLAND
Table of Contents
HOLLYLAND C1 Headset Solidcom HUB Base
Specifications
- Type : Monaural
- Cable Length : Approximately 61″ (1550mm)
- Frequency Information:
- Speaker : 100Hz ~ 10KHz
- Microphone : 100Hz ~ 10KHz
- Distortion: < 1%
- Microphone Sensitivity : Electret (Single-Pointing)
- Microphone Type : Electret (Single-Pointing)
- Impedance : Not specified
- Weight : Not specified
- Working Temperature : Not specified
Product Usage Instructions
Product Installation
- Install Solidcom C1 headset:
- Plug the headset into the 3.5 mm port of the HUB Base and rotate the nut clockwise to secure the headset.
- Move the microphone boom down until you hear a ‘click’. You can now start talking.
- To listen only, make the microphone boom upright. You will hear a ‘click’ sound, and the microphone will mute.
FAQ
- Q: What should I do if I experience interference during usage?
- A : If you experience interference, ensure that the headset is properly connected to the HUB Base. Check for any obstructions or other electronic devices that may be causing interference. If the issue persists, contact HollylandTech support for assistance.
- Q: How do I clean the headset?
- A : Use a soft, dry cloth to gently wipe the headset’s surfaces. Avoid using harsh chemicals or liquids that may damage the headset’s components. Ensure the headset is unplugged before cleaning.
PACKING LIST
- Headset
- Over-ear Leather Cushion
- Microphone Cushion
- Storage Bag
- Quick Guide
- Warranty Card
Note : The amount of items depends on the configuration of a product.
PRODUCT INTERFACES
- Microphone
- Speaker
- Headset Jack
- Microphone Boom
- Adjustable Headband
PRODUCT INSTALLATION AND USAGE GUIDE
Install Solidcom C1 headset:
- Plug the headset into the 3.5 mm port of the HUB Base and rotate the nut clockwise to secure the headset.
- Move the microphone boom down, and you can hear a ‘click’. Then you can start to talk.
- If you just want to listen, make the microphone boom up right. Then, you will hear a ‘click’ sound. And microphone will be mute at the time.
SPECIFICATIONS
Safety Precautions
Do not place the product near or inside heating devices including but not limited a microwave ovens, induction cookers, electric ovens, electric heaters, pressure cookers, water heaters, gas stoves) to prevent the battery from overheating and exploding. Never use non-original charging cases, cables, and batteries with the product. The use of non-original spare parts may cause electric shock, fire, explosion or other dangers.
Support
lf you encounter any problems in using the product and need any help, please contact the Hollyland Support Team via the following ways:
- Hollyland User Group
- HollylandTech
- HollylandTech
- HollylandTech
- support@hollyland-tech.com
- www.hollyland-tech.com
Statement:
All copyrights belong to Shenzhen Hollyland Technology Co., LTD.
Trademark Statement:
Without the written approval of Shenzhen Hollyland Technology Co., LTD, no
organization or individual may copy or reproduce part or all of the content of
the text without authorization, and may not disseminate it in any form.
organization or individual may copy or reproduce part or all of the content of
the text without authorization, and may not disseminate it in any form.
Note:
Due to product version upgrades or other reasons, this quick guide will be
updated from time to time. Unless otherwise agreed, this document is provided
as a guide for use only. All representations, information, and recommendations
in this document do not constitute warranties of any kind, express or implied.
FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
The device has been tested and complies with FCC SAR limits.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>