HOLLYLAND Solidcom M1 Wireless Full Duplex User Manual

HOLLYLAND Solidcom M1 Wireless Full Duplex

Specifications

• Hub Firmware Version: V1.1.5.0
• Beltpack Firmware Version: V1.0.4.5
• USB Disk Memory Requirement: Less than 32GB
• USB Disk Format: FAT32

Product Usage Instructions:

Upgrade Steps

1. Prepare a USB disk with memory less than 32GB and format it to FAT32.
2. Check the base station hardware version from the version info page (H000, H001, or H002). Download the corresponding upgrade file and put it in the root directory of the USB flash.
3. Connect the USB disk to the base station for automatic upgrade.
   • After a successful upgrade, the base station will reboot.
4. Connect the beltpack to the base station one by one for recognition and upgrade.

Upgrade By Browser-Based Software:

1. Check the base station hardware version from the version info page (H000, H001, or H002) and connect the base station via WiFi or LAN.
   • a. Connecting via Wi-Fi:
   • Turn on Wi-Fi on the Solidcom M1 front panel.
   • Connect to a laptop via Wi-Fi using password 12345678.
   • Open a browser, enter IP address 192.168.217.100, and log in (User: admin, Password: 12345678).
   • b. Connecting via LAN:
   • Turn off DHCP on the Solidcom M1 front panel.
   • Connect to a laptop via LAN using an Ethernet cable.
   • Set up the IP address of the laptop in the same network section as the base station.
   • Open a browser, enter the IP address of the base station, and log in (User: admin, Password: 12345678).
2. Go to the settings page, select firmware upgrade, and start the upgrade process. The base station will reboot after a successful upgrade.
3. Connect the beltpack to the base station one by one for recognition and upgrade.

Attention: Ensure stable connections and sufficient power for all devices during the upgrade process.

Frequently Asked Questions (FAQ):

Q: What should I do if the upgrade process fails?

A: If the upgrade process fails, check the connections, and power supply, and ensure you are using the correct firmware version for your device.

Q: Can I use a USB disk larger than 32GB for upgrading?

A: It is recommended to use a USB disk with a capacity of less than 32GB for smooth upgrading.

Firmware Version Release Records

Released date| Hub Firmware| Beltpack Firmware| Release Log| Download Link
---|---|---|---|---
2023-08-10| V1.1.5.0| V1.0.4.5| ●          Updated The channels of Japan Standard| Download
2022-07-15| V1.1.3.6| V1.0.4.5| ●          Enhanced compatibility with cascades| Download

Upgrade Steps

Upgrade By USB Disk

1. Step 1
   • Prepare one USB disk with memory less than 32G, and format it to FAT32.
2. Step 2
   • Check the base station hardware version from the version info page(H000, H001, or H002). download the upgrade files from the link select the corresponding upgrade file, and then put it to the root directory of the USB flash.
3. Step 3
   • Connect the USB disk to the base station, and the device will start the upgrade automatically, after the upgrade is successful, the base station will reboot automatically.
4. Step 4
   • Connect the belt pack to the base station one by one, and the belt pack will be recognized for upgrade.

Upgrade By Browser-Based Software

1. Step 1
   • Check the base station hardware version from the version info page(H000, H001, or H002) and then connect the base station via WiFi or LAN
   • a. Connecting to the base station via Wi-Fi
   • Turn on the Wi-Fi under the network settings on the Solidcom M1 front panel.
   • Connect the base station to a laptop via Wi-Fi with the default password 12345678.
   • Open a browser, enter the IP address 192.168.217.100, and then log in to the web page(User: admin Password:12345678).
   • b. Connecting to the base station via LAN
   • Turn off the DHCP under the network settings on the Solidcom M1 front panel and check the base station IP address (default: 192.168.218.10).
   • Connect the base station to a laptop via the LAN port with an Ethernet cable.
   • Set up the IP address of the laptop and make sure the IP address is in the same network section as the base station such as 192.168.218.25.
   • Open a browser, enter the IP address of the base station, and then log in to the web page(User: admin Password:12345678).
2. Step 2 Switch to the “settings” page, and then go to “firmware upgrade ” and select the corresponding upgrade file, and the device will start the upgrade automatically, after the upgrade is successful, the base station will reboot automatically.
3. Step 3
4. Connect the belt pack to the base station one by one, and the belt pack will be recognized for upgrade.
5. Attention: Make sure the stable connections and all the devices have enough power when upgrading.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>