HOLLYLAND Solidcom 8 Slot Charging Case User Manual
- May 15, 2024
- HOLLYLAND
Table of Contents
Hollyland Solidcom 8-Slot Charging Case
User Manual
V2.0.0
Packing List
(1) (2)
(3) (4)
- Charging Case x1
- DC Adapter x1
- User Manual x1
- Warranty Card x1
Note: The quantity of the items depends on the product configuration.
Product Interfaces
[1] Charging Case:
- Charging Indicator (Orange: Charging/Green: Fully Charged)
- Charging Contact
- DC Charging Interface
[2] Charging Indicator:
- Indicator Light Stays Orange: Charging (for Each Battery Slot)
- Indicator Light Stays Green: Fully Charged (for Each Battery Slot)
Parameters
Interface| DC charging interface
Charging contact
---|---
Dimensions| 159.07×110.85×27.00mm (6.26”x4.36”x1.06”)
Weight| About 234.0g (8.25oz)
Adapter Type| Input: AC 100–240V 50/60 Hz
Output: DC 12/2A
Charging Current for Each Slot| About 420mA
Charging Time| About 2.5 hours
Compatible Model| Headset batteries for Solidcom series intercom systems
Safety Precautions
Do not place the product near or inside heating devices (including but not
limited to microwave ovens, induction cookers, electric ovens, electric
heaters, pressure cookers, water heaters, and gas stoves) to prevent the
battery from overheating and exploding.
Do not use non-original charging cases, cables, and batteries with the
product.
The use of non-original spare parts may cause electric shock, fire, explosion,
or other dangers.
Support
If you encounter any problems in using the product or need any help, please contact Hollyland Support Team via the following ways:
Hollyland User Group
HollylandTech
HollylandTech
HollylandTech
[email protected]
www.hollyland-tech.com
Statement
All copyrights belong to Shenzhen Hollyland Technology Co., Ltd.
Trademark Statement
Without the written approval of Shenzhen Hollyland Technology Co., Ltd., no
organization or individual may copy or reproduce part or all of any written or
illustrative content and disseminate it in any form.
Note:
Due to product version upgrades or other reasons, this User Manual will be
updated from time to time. Unless otherwise agreed, this document is provided
as a guide for use only. All representations, information, and recommendations
in this document do not constitute warranties of any kind, express, or
implied.
FCC Requirement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the device. This
device complies with Part 15 of the FCC Rules.
Operations are subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause
undesired operations.
FCC Radiation Exposure Statement:
The device has been tested and complies with FCC SAR limits.
Note:
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses, and can radiate radio
frequency energy, and if it is not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful interference to
radio or television reception, which can be determined by turning the device
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from that to which
the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.