HOLLYLAND LARK C1 Wireless Microphone System User Manual
- October 30, 2023
- HOLLYLAND
Table of Contents
HOLLYLAND LARK C1 Wireless Microphone System
Product Information
The product contains transmitter(s)/receiver(s) that are exempt from licensing
requirements and comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s).
The device is subject to the following conditions:
- The device must not cause any interference.
- The device must accept any interference, including interference that may cause undesired operation of the device.
Product Usage Instructions
When using the device, ensure that it does not cause any interference with other electronic devices. If you notice any interference, stop using the device immediately. If you experience interference while using the device, it is important to note that the device must accept any interference, including interference that may cause undesired operation of the device. In such cases, try moving the device to another location or adjusting its settings. It is also important to note that the device complies with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s), and therefore should not require any additional licensing or registration.
PACKING LIST
LARK C1 SOLO [JX1 to RX1J Wireless Microphone System
The quantity is based on the product’s various model and is subject to the actual quantity of equipment purchased.
LARK DUO (JX2 to RX1) Wireless Microphone System with Charging Case
The quantity is based on the product’s various model and is subject to the actual quantity of eciuipment purchased.
PRODUCTION INTRODUCTION
PRODUCTION INSTALLATION
- The TX (transmitter) automatically turns on when takes it out from the charging case. Simply clip the TX (transmitter) to a shirt collar.
- Connect the RX to the smartphone.
- Charge the Smartphone via the RX.
PRODUCTION FUNCTION
Noise Cancellation Function
- Blue LED Stays On Device disconnected
- Haar Clear (Noise Reduction) Off by default
- Green LED Stays On HearClear (Noise Reduction) ON
- LED Flashing: Charging
LED Stays On: Fully charged
Charging Case Battery Level
Manual Pairing
Mer the receiver Is connected to the smartphone, long press lX’s ‘raV¼’
button for 3s and then long press RX’s for 3s pairing.
The device has been paired in the factory before shipping. The product needs to pair again when there is disconnection,
PARAMETERS
SUPPORT
If any problems are encountered using the product, please follow these options for receiving technical support:
Hollyland Proclucts User Group i.!J HollylandTech
HolcandTech
Support@hollyland-tech.com
www.holtyland-tech.oom
Note:
The frequency range and wireless transmit power of the device vary based on
the regulations of different countries and regions. Safety Precautions Do not
place the product near or inside heating devices (including but not limited to
microwave ovens, induction cookers, electric ovens, electric heaters, pressure
cookers, water heaters, and gas stoves) to prevent the battery from
overheating and exploding. Never use non-original charging cases, cables, and
batteries with the product. The use of non-original spare parts may cause
electric shock, fire, explosion, or other dangers.
Note: The frequency range and wireless transmit power of the device vary
based on the regulations of different countries and regions.
Safety Precautions
Do not place the product near or inside heating devices (including but not
limited to microwave ovens, induction cookers, electric ovens, electric
heaters, pressure cookers, water heaters, gas stoves) to prevent the battery
from overheating and exploding. Never use non-original charging cases, cables,
and batteries with the product. The use of non-original spare parts may cause
electric shock, fire, explosion, or other dangers.
FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference.
- this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
The device has been tested and complies with FCC SAR limits.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radi?
communicati_ons. However, there is no guarantee that interference will not
occur In a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC Compliance Notice
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>