DIGITUS DN-651160 Industrial 8 + 4-Port L2 Managed Gigabit Ethernet Switch Installation Guide
- June 12, 2024
- DIGITUS
Table of Contents
Industrial 8 + 4-port L2
managed Gigabit Ethernet
(PoE) Switch
Quick
Installation Guide
DN-651160, DN-651161
Overview
This is a L3 managed industrial PoE Ethernet switch with 8 Port
10/100/1000Mbps RJ45 (PoE) +4 Port 1000/2500/10000Mbps SFP, support one
console port.
The Ethernet switch adopts Layer 2 protocol required by the industrial site to
ensure the stability of the communication network. This series of switches
adopt low power consumption and fanless design to ensure no noise
interference, while supporting -40~80°C working temperature and good EMC
electromagnetic compatibility performance to ensure stable work in harsh
industrial environments, and to build fast for industrial applications such as
factory automation, intelligent transportation, and video surveillance.
Stable network terminal access network provides a safe and reliable solution.
Features
- Data control: support 802.3X full-duplex flow control, support network storm suppression
- Redundant network: support STP/RSTP/MSTP, support ERPS (self-healing time <20ms)
- Multicast management: support IGMP Snooping V1/V2/V3
- Redundancy backup: supports the virtual route redundancy protocol VRRP
- VLAN: Support IEEE 802.1Q VLAN, effectively isolate the broadcast domain
- Link aggregation: support link static/dynamic aggregation, providing perfect bandwidth utilization
- QOS: Support COS\DSCP, 4 queues, support WRR\SP scheduling mode
- Security management: support ACL access control list, support 802.1X
- Management function: support WEB, CLI, SNMP management methods
- Monitoring and maintenance: support port mirroring, interface status monitoring, log management
- Supports static routes. IPV6
- Supports NTP clients. Support PTP（1588v2）
- IP40 protection grade
Specification
3.1 standard
IEEE802.3-10BaseT, IEEE802.3u-100BaseTX/100BaseFX, IEEE802.3x-Flow Control,
IEEE802.3af, IEEE802.3at, IEEE802.3z-1000BaseLX, IEEE802.3ab-1000BaseTX,
IEEE802.1ab, IEEE 802.3ae, IEEE802.1D-Spanning Tree Protocol, IEEE802.1w-Rapid
Spanning Tree Protocol, IEEE802.1Q -VLAN Tagging, IEEE802.1p -Class of
Service, IEEE802.1X-Port Based Network Access Control etc.
3.2 Interface
DN-651160: 8 Port Gigabit RJ45 + 4port 10G SFP
DN-651161: 8 Port Gigabit RJ45 (PoE) +4 Port 10G SFP
3.3 Work environment
Working temperature: -40～80 °C
storage temperature: -40～85 °C
relative humidity: 5%～95% (no condensation)
3.4 Switch
Bandwidth (switch capacity): 1.2Tbps
Packet Buffer Memory: 32Mbit
Packet Forwarding Rate: 406Mpps
MAC Address Table: 32K
3.5 Power supply
Input voltage: DC12-48V (DN-651160)
Input voltage: DC48-57V (DN-651161)
(Two-way power redundancy backup)
Access terminal:
Block terminal, Support dual power redundancy
Support built-in over current 4.0A protection
Support reverse connection protection
Max Power consumption: 18W
3.6 Mechanical characteristic
IP40 aluminum housing
DIN rail installation
Natural colling, no fan
Weight: 0.8Kgs
Measurement: 175.6 x 135 x 45.5 mm
3.7 Industrial standard
FCC CFR47 Part 15, EN55032, Class A
IEC61000-4-2 (ESD): ±8kV (contact), ±12kV (air)
IEC61000-4-3 (RS): 10V/m (80~1000MHz)
IEC61000-4-4 (EFT): Power Port: ±4kV; Data Port: ±2kV
IEC61000-4-5 (Surge): Power Port: ±2kV/DM, ±4kV/CM; Data Port: ±2kV
IEC61000-4-6 (CS): 3V (10 kHz-150 kHz); 10V (150 kHz-80MHz)
IEC61000-4-16 (Common mode conduction): 30V (cont.), 300V (1s)
Frequency range：150kHz-80MHz
Impact: IEC 60068-2-27
Free Fall: IEC 60068-2-32
Vibration: IEC 60068-2-6
Package
- Industrial switch 1pcs
- User manual 1pcs
- Block terminal 1pcs
Switch Panel
Side panel: P1 and P2 are the number of connecting terminals, P+1
and P-1 are respectively to the positive and negative poles to be connected;
Earthing screw used for earthing equipment.
Front panel: the green light on RJ45 port is the link light. It is
on, when the connection is established and the transmission data is flashing.
The yellow light on RJ45 port is the POE light, which is only on when the
switch port supplies power to the downlink PD. Green LED on is for system
operation. The power indicator “POW” shows whether the current device is
received power in normal.
There are also green LED for optical link status.
Switch size (mm) 175.6 13545.5
LED Indicator
| LED Indicator | Status | Definition |
|---|---|---|
| Power | Red LED on | Power work in normal |
| Red LED off | No power or power in trouble | |
| RJ45 LED | Yellow LED on | Ethernet work in normal |
| Yellow LED flashing | Link communication in normal | |
| Green LED on | PoE feeding to PD device in normal | |
| Green LED off | No PoE work | |
| RUN | Green LED slowing flashing | System run in normal |
| Optical LED | Green LED on | Optical work in normal |
Installation Caution
7.1 Installation precautions
In order to avoid damage to equipment and personal injury caused by improper
use, please follow the following precautions:
- In order to avoid damage caused by falling of the equipment, please put the equipment in a stable environment.
- When supplying power to the equipment, pay attention to confirm the range of power supply voltage, as well as the positive and negative poles of the power supply, so as not to damage the equipment by wrong operation.
- In order to reduce the risk of electric shock, ensure that the equipment is well grounded in the working environment.
- No matter when, please do not arbitrarily remove the equipment shell.
- When placing the switch, please avoid the area with dust and strong electromagnetic interference
7.2 Din rail installation
The first step is to check the grounding and stability of the guide rail: the
guide rail slot of the switch is clamped into the guide rail; the second step:
from the center to both sides of the guide rail positioning screws in order.
Step 3:
Use screws to fix the mounting rail card slot on the fixed guide groove at
both ends of the guide rail to ensure that the guide rail and the switch are
fixed on the guide rail vertically and stably. 7.3 grounding
Fix the grounding wire to the grounding screw above the switch, and ensure
good reliable connection of the grounding system.
7.4 Power Connection
Insert the power cord into the specified position of the 6-core terminal, and insert the terminal into the standard power supply inlet (P+1 and P-1 input corresponding to the first power supply P1, and P+2 and P-2 input corresponding to the second power supply P2). 
Management system Login
This series of Managed ethernet switches provides a serial port-based
management system program debugging port. Located at the front of panel to log
in to the command line.
Console port: baud rate 115200
Web IP: 192.168.10.12
User name: admin
Password: admin
For detail Web manual support, please visit product website at
www.assmann.com
This is a Class A product. In home environment, this product may cause radio
interference. In this case, the user may be required to take appropriate
measures.
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is
part of the shipping content. If the Declaration of Conformity is missing,
youcan request it by post under the below mentioned manufacturer address
www.assmann.com
ASSMANN Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid,
German
Documents / Resources
|
DIGITUS DN-651160 Industrial 8 + 4-Port L2 Managed Gigabit Ethernet
Switch
[pdf] Installation Guide
DN-651160, DN-651161, DN-651160 Industrial 8 4-Port L2 Managed Gigabit
Ethernet Switch, DN-651160, Industrial 8 4-Port L2 Managed Gigabit Ethernet
Switch, Managed, Gigabit Ethernet Switch, Ethernet Switch, Switch
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>