STARLINK R211 Dish and Router User Guide
- June 5, 2024
- Starlink
Table of Contents
STARLINK R211 Dish and Router
SETUP
Plug everything in
Power up the Router by connecting the power cord and dish cable through the
bottom ports of the Router. When everything is connected correctly, the Router
LED will glow a pulsing white.
Power Supply LED:
When the Router is powered, the LED glows solid white
Router LED:
Pulsing White: Initializing Solid White: Waiting for Internet Solid Blue:
Connected to Internet
CONNECT
Connect to the Router
Once the Router LED is solid white and no longer pulsing, the software is
initialized and the Router is ready for login. This takes approximately 2
minutes.
Connect using the Network ID and password. Once the system has successfully
established an internet connection, the Router LED will glow blue, and you
will be able to browse the web.
SETUP TIPS
Changing Your Network ID Or Password
To access the Router Admin Portal on a connected device (e.g., phone, tablet,
PC) via the Starlink GUI, open the Starlink App, or enter
http://192.168.100.1/ in your Internet Browser. STARLINK GUI => SETTINGS Once
in SETTINGS, change the IWFI CONFIGURATION.
Regulatory information
For regulatory identification purposes, your product is assigned a Model No.: UTR-211 FCC ID: 2AWHPR211, IC: 26207-UTR211 To view the electronic regulatory label on a connected device (e.g., phone, tablet, PC) via the Starlink GUI, open the Starlink App, or enter http://192.168.100.1/ in your Internet Browser. STARLINK GUI => Support => Legal => Regulatory Label Alternatively, the regulatory markings might be located on the bottom of the unit, on the packaging, or elsewhere in this document.
Federal Communications Commission Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 28cm between the radiator & your body.
Industry Canada statement:
This device complies with ISED’s licence-exempt RSSs. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use
to reduce the potential for harmful interference to cochannel mobile satellite
systems;
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
greater than 34 cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>