anslut 024314 Street Lamp Instruction Manual
- June 12, 2024
- anslut
Table of Contents
STREET LAMP
OPERATING INSTRUCTIONS
Original instructions
024314 Street Lamp
Jula AB reserves the right to make changes to the product. Jula AB claims copyright on this documentation. It is not allowed to modify or alter this documentation in any way and the manual shall be printed and used as it is in relation to the product. For the latest version of operating instructions, refer to the Jula website.
© JULA AB 2022-11-28
JULA AB
BOX 363, 532 24 SKARA, SWEDEN
SAFETY INSTRUCTIONS
- The product is only intended for outdoor use.
- Disconnect the power supply before installation.
- Before cleaning, maintenance and/or other work on the product, switch off the power supply by removing the fuse or pulling out the plug.
- Products with transformers must only be used with the original transformer.
- Do not allow children to play with the packaging material or the product.
- Do not connect the light to the mains while it is still in the pack.
- Stop using the product immediately if it gets damaged, especially the power cord, plug and/or socket, and if it is not working properly.
- Repairs must be carried out by an authorised electrician.
- Do not attempt to modify or repair the product. Repairs that are not carried out correctly can result in a risk of serious personal injury and/or death.
- The product’s earth wire (green/yellow) is connected to earth.
- Be careful not to damage the insulation on the wires during installation. Make sure that the wires do not come into contact with sharp edges.
- Damaged insulation can result in a risk of electric shock.
- Check that the mains voltage matches the rated voltage on the type plate.
- The plug, power cord, wires and connections must not be subjected to mechanical stress.
- The light must only be used with its casing.
- When the product is switched on the bulb gets very hot. Allow the product to cool before replacing the bulb.
NOTE:
Do not tamper with the product casing – risk of electric shock and/or material
damage.
ELECTRICAL SAFETY!
New installations and extensions to existing systems should always be carried out by an authorised electrician. If you have the necessary experience and knowledge (otherwise contact an electrician), you can replace power switches and wall sockets, fit plugs, extension cords and light sockets. Incorrect installation can result in fatal injury and the risk of fire.
SYMBOLS
| Read the instructions.
---|---
| Non-
replaceable light source.
| Non-replaceable actuator.
| Approved in accordance with the relevant directives.
****| Recycle discarded product in accordance with local regulations.
TECHNICAL DATA
| Voltage | 230 V ~ 50 Hz |
|---|---|
| Output | 60 W |
| Colour rendering index | CRI 76 |
| Colour temperature | 5000 K |
| Colour tone | Neutral white |
| Luminous flux | 9000 lm |
| Life span | 50000 h |
| Protection rating | IP66 |
| Size | W 665 x H 134 x D 280 mm |
DESCRIPTION
Bright light for installation outdoors. Fits Ø43 or Ø60 mm lampposts. Made
of powder coated aluminium.
INSTALLATION
Connect the live wire (L) to the brown wire and the neutral wire (N) to the
blue wire. The green/yellow wire must only be connected to earth.
FIG. 1
FIG. 2
FIG. 3
- Brown: L
- Blue: N
- Yellow/green: GND
FIG. 4
FIG. 5
FIG. 6
PRODUCT INFORMATION SHEET
| Supplier’s name or trademark: | Anslut |
|---|---|
| Supplier’s address (a): | Jula AB, Box 363, 532 24 SKARA |
| Model designation: | 024314 |
| Type of light source: | |
| Lighting technology used: | LED |
| Type of socket for light source (or other electrical interface) | 100-240V AC |
| 50 Hz |
Light source connected to mains supply or light source not connected to mains
supply:| MLS| Connected light source (CLS):| no
Light source with optional colour:| no| Casing:| –
High luminance light source:| no| |
Anti-glare shield:| no| Dimmable:| yes
Product parameters
Parameter| Value| Parameter| Value
General product parameters:
Energy consumption in on-mode (kWh/1000 h), rounded off.| 60| Energy
efficiency class| D
Useful luminous flux (Φuse), indicating if it refers to the flux in a sphere
(360˚), in a wide cone (120˚) or in a narrow cone (90˚).| 9000 in sphere
(360°)| Correlated colour temperature, rounded to the nearest 100 K, or the
interval of correlated colour temperatures that can be set, rounded to the
nearest 100 K.| 5000
On-mode power (Pon), expressed in W.| 60.0| Standby power (Psb), expressed in
W and rounded to the second decimal.| –
Networked standby power (Pnet) for CLS, expressed in W and rounded to the
second decimal.| –| Colour rendering index, rounded to the nearest integer, or
the range of CRI values that can be set.| 76
Outer dimensions without separate driver, driver for lighting and non-lighting
parts, where appropriate (in mm).| Height| 134| Spectral power distribution in
the interval 250 nm to 800 nm, at full-load.| See figure on the last page.
Width| 665
Depth| 280
Claim of equivalent power (c).| –| If yes, equivalent power (W)| –
| | Chromaticity coordinates (x and y)| 0.348
0.350
Parameters for LED and OLED light sources:
R9 colour rendering index value| 0| Life span factor| 1.00
Lumen maintenance factor| 0.98| |
Parameters for LED and OLED mains light sources:
Displacement factor (cos φ1)| 0.00| Colour consistency in mcadam ellipses| 5
Claims that an LED light source replaces a fluorescent light source without
integrated ballast of a particular wattage.| -(b)| If yes, then replacement
claim (W)| –
Flicker metric (Pst LM)| 0.0| Stroboscopic effect metric (SVM)| 0.0
(a)”–”: not applicable.
(b)”–”: not applicable.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>