anslut 024997 Wireless LED Tube Light User Manual
- June 12, 2024
- anslut
Table of Contents
024997 Wireless LED Tube Light
User Manual
TUBE LED 024997
024997 Wireless LED Tube Light
SAFETY INSTRUCTIONS
Read these instructions carefully before installation and use, and save them for future reference.
- The product is not dimmable.
- Disconnect the power supply before installation.
- The product is only intended for indoor use in dry areas. Damp areas and outdoor environments require products with a higher protection rating (IP code).
- Never modify the product or any of its parts in any way – risk of personal injury or material damage.
- The product is intended for lights with 2-pin IEC approved G13 standard sockets.
- The product must be installed by an authorised electrician in accordance with the relevant electrical safety regulations.
SYMBOLS
| Read the instructions.
---|---
| Not dimmable
| Not suitable for use in damp areas
| Approved in accordance with the relevant directives.
| Recycle discarded product in accordance with local regulations.
TECHNICAL DATA
| Voltage | 230 V / 50 Hz |
|---|---|
| Power | 30 W |
| Socket | T8 |
| Colour rendering index | CRI 80 |
| Colour tone | Neutral white |
| Luminous flux | 4500 lm 360° |
| Life span | 50000 h |
| Length | 150 cm |
| Diameter | 2.8 cm |
DESCRIPTION
Strip light with LED light source and long life span of up to 50,000 hours. Delivers a neutral white light.
INSTALLATION
Wiring diagram, new installation, LED strip light
FIG. 1
Wiring diagram, after installation in lights with choke coil
A. Choke coil
B. Conventional T8 strip light
C. Starter
FIG. 2
A. Choke coil
B. LED strip light
C. LED fuse (replace the starter with the LED fuse)
FIG. 3
Wiring diagram, after installation in light with electronic actuator
A. Electrical ballast
B. Conventional T8 strip light
FIG. 4
- Remove the electrical ballast as shown in the figure.
- Connect a direct wire between pin 2 and 3 on the light.
- Connect pin 1 to the mains phase (L) and pin 4 to neutral (N).
A. Remove the electrical ballast
B. LED strip light
FIG. 5
PRODUCT INFORMATION SHEET
| Supplier’s name or trademark: | Insult |
|---|---|
| Supplier’s address (a): | Jula AB, Box 363, 532 24 SKARA |
| Model identifier: | 024997 |
| Type of light source: | |
| Lighting technology used: | LED |
| Light source cap-type (or other electric interface): | 230V AC 50 Hz |
Light source connected to mains supply or light source not connected to mains
supply:| MLS| Connected light source (CLS):| no
Colour-tunable light source:| no| Envelope:| –
High luminance light source:| no| |
Anti-glare shield:| no| Dimmable:| no
Product parameters
Parameter| Value| Parameter| Value
General product parameters:
Energy consumption in on-mode (kWh/1000 h), rounded up to the nearest
integer.| 30| Energy efficiency class| D
Useful luminous flux (Φuse), indicating if it refers to the flux in a sphere
(360˚), in a wide cone (120˚) or in a narrow cone (90˚).| 4 500 in sphere
[360°]| Correlated colour temperature, rounded to the nearest 100 K, or the
range of correlated colour temperatures, rounded to the nearest 100 K, that
can be set.| 4 000
On-mode power (Pun), expressed in W.| 30.0| Standby power (PS), expressed in W
and rounded to the second decimal.| –
Networked standby power (Pent) for CLS, expressed in W and rounded to the
second decimal.| –| Colour rendering index, rounded to the nearest integer, or
the range of CRI-values that can be set.| 80
Outer dimensions without separate control gear, lighting control parts and
non-lighting control parts, if any (millimeter).| Height| 28| Spectral power
distribution in the range 250 nm to 800 nm, at full-load.| See image in last
page
Width| 28
Depth| 1 500
Claim of equivalent power (c)| –| If yes, equivalent power (W)| –
| | Chromaticity coordinates (x and y)| 0,375 0,369
Parameters for LED and OLED light sources:
R9 colour rendering index value| 10| Survival factor| 0,90
The lumen maintenance factor| 0,97| |
Parameters for LED and OLED mains light sources:
Displacement factor (cos φ1)| 0,90| Colour consistency in McAdam ellipses| 5
Claims that an LED light source replaces a fluorescent light source without
integrated ballast of a particular wattage.| -(b)| If yes then replacement
claim (W)| –
Flicker metric (Past LM)| 0,1| Stroboscopic effect metric (SVM)| 0,9
(a)”–”: not applicable;
(b)”–”: not applicable;
Spectrum
Documents / Resources
|
anslut 024997 Wireless LED Tube
Light
[pdf] User Manual
024997, 024997 Wireless LED Tube Light, Wireless LED Tube Light, LED Tube
Light, Tube Light, Light
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>