Clore Automotive 404202 Jump n Carry Vehicle Booster Cables User Manual
- June 12, 2024
- Clore Automotive
Table of Contents
Clore Automotive 404202 Jump n Carry Vehicle Booster Cables
Product Information: Vehicle Booster Cables
- Part Numbers: 410122, 404202, 402252, 401252, 422252
- Contains chemicals, including lead, known to the State of California to cause cancer, birth defects, and other reproductive harm. Wash hands after handling.
- Designed for jump-starting car, truck, or boat batteries.
- Jump starting should be done following the instructions provided by the vehicle manufacturer.
- General precautions and safety instructions must be followed to ensure safe operation.
- Compatible with batteries of the same voltage (e.g., 6V or 12V).
- Power sources other than batteries should not exceed 15V for use with 12V systems or 8V for use with a 6V system.
- Jump starting should be performed with both vehicles positioned adjacent to each other but not touching.
- Turn off all electrical loads and set the parking brake on all vehicles before the jump starts.
- Positive cables should be connected to the positive terminals of both vehicle batteries.
- Follow a specific connection sequence and do not allow the clamps to touch any vehicle part other than the battery terminal.
- Do not crank the disabled vehicle for more than 6 seconds. If it doesn’t start, turn off the ignition and wait for 3 minutes before attempting again.
- Booster cables should be removed in the opposite order of the connection sequence once the disabled vehicle is started.
Product Usage Instructions: Jump Starting
- Check the clamps and cables for any damage (burn marks, damaged handles, springs, or exposed copper wiring) before every use. Replace any damaged parts.
- Ensure that the battery is jumped and the booster source has the same voltage (6V or 12V).
- Position the host vehicle or power source adjacent to the disabled vehicle with a discharged battery, ensuring they do not touch each other.
- Turn off all electrical loads and set the parking brake on all vehicles. Place automatic transmission vehicles in PARK and manual transmission vehicles in NEUTRAL.
- Ensure that the vent caps on both batteries are tight and level. Place a damp cloth over any vent caps, keeping it clear of fan blades, belts, and other moving parts.
- On a negative ground system, connect the positive (POS, +) cable to the positive (pos, +) terminals of both vehicle batteries (host and disabled vehicles). Avoid touching any vehicle part other than the battery-positive terminal with the clamps.
- Connect the negative (NEG, -) cable to the negative (neg, -) terminal of the host vehicle’s battery.
- Start the host vehicle’s engine and allow it to idle.
- Attempt to start the disabled vehicle. Do not crank for more than 6 seconds. If the vehicle does not start, turn off the ignition and wait for 3 minutes before attempting again.
- Once the disabled vehicle is started, remove the booster cables in the opposite order of the connection sequence: first, remove the negative cable from the host vehicle’s battery, then remove the positive cable from both batteries.
Failure to follow instructions may cause damage or explosion, always shield
eyes. Read entire instruction manual before use.
Warning: This product contains chemicals, including lead, known to the
State of California to cause cancer, birth defects and other reproductive
harm. Wash hands after handling
Safety Information
WARNING
Read these instructions completely before using the Booster Cables and save
them for future reference. Before using the Booster Cables to jump-start a
car, truck or boat read these instructions and the instruction manual/safety
information provided by the car, truck, or boat manufacturer. Following all
manufacturers’ instructions and safety procedures will reduce the risk of
accidents. Working around lead-acid batteries may be dangerous. Lead-acid
batteries release explosive gases during normal operation, charging, and jump-
starting. Carefully read and follow these instructions for safe use. Always
follow the specific instructions in this manual\ and on the Booster Cables
each time you jump-start using the Booster Cables. All lead-acid batteries
(car, truck and boats) produce hydrogen gas which may violently explode in the
presence of fire or sparks. Do not smoke, use matches or a cigarette lighter
while near batteries. Do not handle the battery while wearing vinyl clothing
because static electricity sparks are generated when vinyl clothing is rubbed.
Always wear eye protection, appropriate protective clothing and other safety
equipment when working near lead-acid batteries. Do not touch your eyes while
working on or around lead-acid batteries. Use extreme care while working
within the engine compartment, because moving parts may cause severe injury.
Read and follow all safety instructions published in the vehicle’s Owner’s
Manual. Batteries being jump-started with the Booster Cables likely contain
liquid acids which are hazardous if spilled.
General precautions for use
- Someone should always be within range of your voice or close enough to come to your aid when you work near a lead-acid battery.
- Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing or eyes. Protective eyewear should always be worn when working near lead-acid batteries.
- If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately flood eye with cold running water for at least 10 minutes and get medical attention immediately.
- Be extra cautious to reduce risk of dropping a metal tool onto a battery. It might spark or short-circuit the battery or another electrical part that may cause an explosion.
- Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery. A lead-acid battery can produce a shortcircuit current high enough to weld a ring or the like to metal, causing a severe burn.
- NEVER charge or jump-start a frozen battery.
- To prevent arcing, NEVER allow clamps to touch together or to contact the same piece of metal.
- Use of an attachment not recommended or sold by the manufacturer may result in a risk of damage to the unit or injury to personnel.
- The Booster Cables may be used under any weather condition – rain, snow, hot
- cold temperatures.
- Do not submerge in water.
- Do not operate with flammables such as gasoline, etc.
Jump Starting Instructions
Safety Check List
Always Perform this Step Before Use to Ensure Safe Operation. Check to make
sure that the clamps and cables are in good working order. Signs of damage
include, but are not limited to the following:
- Burn marks on the jaws
- Damaged clamp handles
- Damaged clamp springs
- Damaged cables where copper wiring may be exposed (insulation jacket deteriorated, cut, or missing)
- Verifying these simple checkpoints before every use will keep your Booster Cables safe to use and increase its service life.
Note : Both the battery to be jumped and the booster source must be of
the same voltage (6 or 12V, etc.).
Note: Power sources other than batteries should not exceed 15V for use
with 12V systems or 8V for use with a 6V system.
Note : Position the “host” vehicle, or other power source, adjacent to
the “disabled” vehicle with a discharged battery so that booster cables can be
connected easily between both vehicles. Make certain that the vehicles do not
touch each other
-
Turn off all electrical loads and set the parking brake on all vehicles. Place automatic transmission vehicles in “PARK” and manual transmission vehicles in “NEUTRAL”.
-
Be sure that the vent caps are tight and level on both batteries. Place a damp cloth over any vent caps on each battery, making certain it is clear of fan blades, belts, and other moving parts.
-
Determine whether the discharged (dead) battery has the negative (-) or the positive (+) terminal connected to the ground. The ground lead is connected to the engine block, the vehicle frame, or some other good metallic ground. The battery terminal connected to the starter is the one that is not grounded. (All vehicles manufactured in the U.S.A. after 1955 have the negative battery terminal grounded. All European and Asian passenger vehicles manufactured after 1971 have the negative battery terminal grounded.)
-
On a negative ground system, connect the positive (POS, +) cable to the positive (pos, +) terminals of both vehicle batteries (host and disabled vehicles). Do not allow the clamps to touch any vehicle part other than the battery-positive (POS, +) terminal.
-
On a negative ground system, connect one end of the negative (NEG, -) cable to the negative (NEG, -) terminal of the host vehicle battery. Connect the other end of the negative (NEG, -) cable to a vehicle ground on the disabled vehicle (engine
block, vehicle frame, or other heavy-gauge, non-moving, unpainted metal part – never connect to the carburetor, fuel lines, or sheet metal body parts). Again, do not allow the clamps to touch each other or a common conductor. -
Start the host vehicle’s engine and allow it to idle. Attempt to start the disabled vehicle. Do not crank for more than 6 seconds. If the vehicle does not start in this amount of time, turn the ignition of the disabled vehicle to OFF and allow to rest for 3 minutes before attempting again.
-
Once the disabled vehicle is started, remove the booster cables in the opposite order of the connection sequence.
Jump-N-Carry Limited Warranty
Clore Automotive warrants this product to be free from defects in material or workmanship for a period of one year from the date of the original end-user purchase. This warranty extends to each person who acquires lawful ownership within one year of the original retail purchase, but is void if the product has been abused, altered, misused or improperly packaged and damaged when returned for repair. This warranty applies to the product only and does not apply to any accessory items included with the product which are subject to wear from usage; the replacement or repair of these items shall be at the expense of the owner.
THE TERMS OF THE CLORE AUTOMOTIVE LIMITED WARRANTY CONSTITUTE THE BUYER’S SOLE AND EXCLUSIVE REMEDY. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THIS EXPRESS WARRANTY. AFTER 1 YEAR FROM THE DATE OF PURCHASE, ALL RISK OF LOSS FROM WHATEVER REASON SHALL BE PUT UPON THE PURCHASER. CLORE AUTOMOTIVE SHALL NOT BE LIABLE FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES UNDER ANY CIRCUMSTANCES: CLORE AUTOMOTIVE’S LIABILITY, IF ANY, SHALL NEVER EXCEED THE PURCHASE PRICE OF THIS PRODUCT REGARDLESS OF WHETHER LIABILITY IS PREDICATED UPON BREACH OF WARRANTY (EXPRESS OR IMPLIED), NEGLIGENCE, STRICT TORT OR ANY OTHER THEORY. Some states do not permit the limitation of warranties or the limitation of consequential or incidental damages, so the above disclaimer and limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For Warranty or Service
If this product fails within the first 365 days after retail purchase due to a
defect in material or workmanship, return it to your place of purchase for an
exchange. A valid, dated sales receipt is required to obtain service under
this warranty. For best service and to receive periodic product updates,
follow the instructions below to register your purchase: Please visit
www.cloreregistration.com. Click on the
Jump-N-Carry logo, complete the information in the web form and click
“submit”. For questions regarding your product, please contact Clore
Automotive Technical Service at 800.328.2921 913.310.1050 or
www.cloreautomotive.comAttempt to start the
disabled vehicle. Do not crank for more than 6 seconds. If the vehicle does
not start in this amount of time, turn the ignition of the disabled vehicle to
OFF and allow it to rest for 3 minutes before attempting again. Once the
disabled vehicle is started, remove the booster cables in the opposite order
of the connection sequence.
Jump-N-Carry Limited Warranty
Clore Automotive warrants this product to be free from defects in material or
workmanship for a period of one year from the date of the original end-user
purchase. This warranty extends to each person who acquires lawful ownership
within one year of
the original retail purchase but is void if the product has been abused,
altered, misused or improperly packaged and damaged when returned for repair.
This warranty applies to the product only and does not apply to any accessory
items included with the product which are subject to wear from usage; the
replacement or repair of these items shall be at the expense of the owner.
THE TERMS OF THE CLORE AUTOMOTIVE LIMITED WARRANTY CONSTITUTE THE BUYER’S SOLE AND EXCLUSIVE REMEDY. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THIS EXPRESS WARRANTY. AFTER 1 YEAR FROM THE DATE OF PURCHASE, ALL RISK OF LOSS FOR WHATEVER REASON SHALL BE PUT UPON THE PURCHASER. CLORE AUTOMOTIVE SHALL NOT BE LIABLE FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES UNDER ANY CIRCUMSTANCES: CLORE AUTOMOTIVE’S LIABILITY, IF ANY, SHALL NEVER EXCEED THE PURCHASE PRICE OF THIS PRODUCT REGARDLESS OF WHETHER LIABILITY IS PREDICATED UPON BREACH OF WARRANTY (EXPRESS OR IMPLIED), NEGLIGENCE, STRICT TORT OR ANY OTHER THEORY.
Some states do not permit the limitation of warranties or the limitation of
consequential or incidental damages, so the above disclaimer and limitation
may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. For Warranty or
Service If this product fails within the first 365 days after retail purchase
due to a defect in material or workmanship, return it to your place of
purchase for an exchange. A valid, dated sales receipt is required to obtain
service under this warranty. For best service and to receive periodic product
updates, follow the instructions below to register your purchase: Please visit
www.cloreregistration.com. Click on the
Jump-N-Carry logo, complete the information in the web form and click
“submit”. For questions regarding your product, please contact: Clore
Automotive Technical Service
800.328.2921 913.310.1050
www.cloreautomotive.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>