Leviton 47603-24P 24PORT STRUCTURED MEDIA PANEL Installation Guide

Leviton 47603-24P 24PORT STRUCTURED MEDIA PANEL

Pre-Configured Structured Cabling Panels

APPLICATION

One of six Pre-Configured Structured Cabling Panels, which may be used to connect basic telephone service, data (with a network hub), and, on selected versions, video service for home or office cabling. Panels are designed to fit into Structured Media Centers™ (Models 100, 140, 280, or 420), or plastic mounting hardware may be removed and the unit may be screwed directly onto a plywood backboard.

PLANNING

• Your Pre-Configured Structured Cabling Panel may consist of one or more of the following components: a 1×9 Bridged Telephone Module, a Category 5e Voice and Data Module, a Telephone Distribution Module, or a 6-way Video Splitter.
• Plan all of your cable routings carefully to be sure the selected distribution panel will satisfy your requirements. Determine the number of outlet locations required for a basic phone, fax, modem, and TV service. Additional Category 5e Voice and Data Modules (PN# 47603-C5) and 1×9 Bridged Telephone Expansion modules (PN# 47603-110) are available separately.

Modules:

Your Pre-Configured Structured Cabling Panel consists of one or more of the following modules:

• Category 5e Voice and Data Module: used for terminating remote connections (from wall outlets) for voice, fax, modem, and computer. Use it to provide dial tone to an outlet, or to link to a network hub.
• Telephone Distribution Module: accepts incoming service from the telephone service provider (dial tones) and provides dial tone (for up to 4 lines) to ports on the Category 5e Voice and Data Module by way of short patch cords.
• 1×9 Bridged Phone Module: used for connecting up to four phone lines for voice, fax, and modem in a bridged wiring configuration.
• 6-way Video Splitter: routes basic video signals from one input to as many as six remote televisions.[Should the local signal need active attenuation, an optional video module will be required (PN#48210-VA).]

Installation

Position the Structured Cabling Panel inside the SMC enclosure. Align the plastic Push Lock Pins (plunger out) on the distribution panel with the appropriate mounting holes on the enclosure. Seat the panel in place, resting flat against the back of the panel, and then press the Push Lock Pins inward with your thumb to lock it into place. You will know the push locks are secure if they “click” when pressing in.

Typical wiring of an SMC 140 shown, using an Advanced Small Office Pre- configured Structured Cabling Panel.

IMPORTANT INSTRUCTIONS

1. Read and understand all instructions. Follow all warnings and instructions marked on the product.
2. Do not use this product near water—e.g., near a tub, wash basin, kitchen sink or laundry tub, in a wet base-ment, or near a swimming pool.
3. Never push objects of any kind into this product through openings, as they may touch dangerous voltages.
4. SAVE THESE INSTRUCTIONS.

SAFETY INFORMATION

1. Never install communications wiring or components dur-ing a lightning storm.
2. Never install communications components in wet loca-tions unless the components are designed specifically for use in wet locations.
3. Never touch uninsulated wires or terminals unless the wiring has been disconnected at the network interface.
4. Use caution when installing or modifying communications wiring or components.
5. To prevent electrical shock, each opening must be filled with a module.

CATEGORY 5e VOICE & DATA MODULE

Connecting the Category 5e Voice and Data Module

• Run twisted pair cable to the Category 5e Voice and Data Module from wall outlets. Strip about 3˝ of outer jacket from the cable. Punch individual cable pairs down on the six white connectors on the sides of the Module. Match the color coding of the wires to the colors on the connector. If you do not have a professional grade termination tool, use the plastic tool supplied with the module. (See 110 Punchdown Procedure.) All four pairs of each cable must be terminated. (The module supports T568A wiring pattern – See figure 2.)
• Punch the individual conductors down onto the appropriate connections. If you are using the plastic tool, make sure you trim the excess wire ends with a separate tool, such as a side cutter.
• Use ports to route telephone service to wall outlets, or to connect to a data hub.(Ports will accept both 6 and 8-position plugs.)

TELEPHONE DISTRIBUTION MODULE

Connecting the Telephone Distribution Module

Run twisted pair cable to the Telephone Distribution Module from the telephone company demarcation point. Strip about 3˝of outer jacket from the cable. Punch individual cable pairs down on the white connector at the top of the Telephone Distribution Module. If you do not have a professional grade termination tool, remove excess wire with side cutters.

NOTE: One pair of wires corresponds to each line from the phone company.(Line 1=blue, Line 2=orange, Line 3=green, Line 4=brown.) (See Figure 2.)

By punching incoming Telco lines at the top of the Telephone Distribution Module, the lines will be routed to the three columns of ports. The short (3˝) 8-position patch cord on the left of the module acts to provide this bridge between the incoming lines and the columns of jacks below. (This is also a disconnect point between the home and the telephone service provider for testing purposes.)

Line 1 and Line 2 will both be carried to the first column of ports, which provides two-line phone service for multi-line phones. (For single-line phones, only Line 1 will be accessible.) Line 3 will be carried to the second row, and Line 4 to the third. These ports are single-line only.

An RJ31X port on the top left of the module will allow connection of a security system, and allow an override of telephone services in case of emergency.

Using the Telephone Distribution Module with the Category 5e Voice and Data Module

To connect phone service from the Telephone Distribution Module to the various wall outlets around the home or office, simply connect a patch cord from the appropriate column on the Telephone Distribution Panel to the desired port on the Category 5e Voice and Data Module. (See figure 1.)

1X9 BRIDGED TELEPHONE MODULE

Connecting the 1×9 Bridged Telephone Module

Run twisted pair cable to the Bridged Telephone Module from the telephone company demarcation point. Strip 3˝ of outer jacket from the cable. Punch individual cable pairs down on the first white connector at the top of the Bridged Telephone Module. If you do not have a professional grade termination tool, use the plastic tool supplied with this panel. If you are using the plastic tool, remove excess wire with side cutters (See 110 Punchdown Procedure.)

NOTE: One pair of wires corresponds to each line from the phone company. (Line 1=blue, Line 2=orange, Line 3=green, Line 4=brown). (See Figure 2.)

By punching incoming Telco lines at the top of the Bridged Telephone Module, the lines will be bridged to all connectors on the module.

Terminate incoming twisted pair cables (coming from the wall outlets throughout the home) onto any of the nine remaining rows of connectors. Punch down pairs based on which phone line is desired at which location. On a one- line phone, the primary line is represented by the blue/white wire pair. This pair should be punched down onto a point corresponding to the phone line you want connected (Line 1=blue, Line 2=orange, Line 3=green, line 4=brown).

NOTE: The secondary line on a two-line telephone is represented by the orange/white pair.

Example: To run Line 1 (blue in from Telco) to a phone in the kitchen, simply punch all wires down on their corresponding colors (blue pair to the blue connection point, etc.) (See Figure 2.)

Example: To run Line 3 (Green in from Telco) to a phone in the office, punch incoming green pair onto the blue (Line 1) connection point. (The blue incoming pair can be switched over to the green connection point while orange and brown pairs remain the same.) (See Figure 3.)

6-WAY COAXIAL SPLITTER

Connecting the 6-Way Splitter

Run coaxial cable to the 6-Way Splitter from incoming cable TV service or a rooftop antenna. Attach a male F-type connector onto the incoming cable and screw onto the middle termination point (marked “IN”) of the 6-Way Splitter. In a similar manner, terminate the coaxial cables coming from the wall outlets on the other six ports. All TVs now connected to the 6-Way Splitter will receive the same service. If there are unused outputs on the 6-Way Splitter, it is recommended that you install 75 Ohm termination caps (PN# 40984) onto these outputs. This will help reduce the likelihood of signal distortion and “ghosting.”

110 PUNCHDOWN PROCEDURE

Lace wires into proper slots according to selected configuration.

Using Plastic Tool:

1. Push wire into slot with the tool. (See Figure 4.)
2. Trim excess wire with diagonal cutter. (See Figure 5.)

Using Professional Punch Tool:

1. Orient tool with cutting blade as shown. (see Figure 6.)
2. Push straight down until tool seats and trims wire, making a clicking noise.

THE FOLLOWING PANELS ARE AVAILABLE FROM LEVITON

• Basic Telephone and Video Unit:
  Combines a Bridged Telephone Module and 6-Way Video Splitter in a dedicated bracket for essential telephone and video distribution. Will distribute 9 cables for telephone and 6 for video. Available as a stand-alone unit or as part of a kit with SMC-100 or SMC-140. Dimensions: 6.25˝h x 13.06˝w x 2.50˝d

• Basic Home Networking Unit:
  Combines a dedicated Bridged Telephone Module, Category 5e Voice and Data Module, and a 6-way Video Splitter in a dedicated bracket for essential telephone, video distribution and home networking. Will distribute 9 cables for telephone, 6 for data networking and 6 for video. Available as a stand- alone unit, or as part of a kit with SMC-100 or SMC-140. Dimensions 6.25˝h x 13.06˝w x 2.50˝d

• Advanced Home Telephone Unit:
  Combines a Telephone Distribution Module, Category 5e Voice and Data Module, and 6-way Video Splitter in a dedicated bracket for multi-line systems with video distribution. Will distribute 6 cables for voice/telephone and/or data networking and 6 for video. Available as a stand-alone unit, or as part of a kit with SMC-100 or SMC-140. Dimensions 6.25˝h x 13.06˝w x 2.50˝d

• Advanced Small Office Unit:
  Combines a Telephone Distribution Module, two Category 5e Voice and Data Modules and 6-way Video Splitter in a dedicated bracket for multi-line systems and full-home networking with video distribution. Will distribute 12 cables for voice/telephone and/or data networking with 6 for video. Available as a stand-alone unit, or as part of a kit with SMC-100 or SMC-140. Dimensions 6.25˝h x 13.06˝w x 2.50˝d

• 18-Port Structured Media Panel:
  Combines a Telephone Distribution Module and three Category 5e Voice and Data Modules in a dedicated bracket for multi-line systems and expanded home networking. Will distribute 18 cables for voice/telephone and/or data networking. Available as a stand-alone unit only. Dimensions 6.25˝h x 13.06˝w x 2.50˝d

• 24-Port Structured medial Panel:
  Combines a Telephone Distribution Module and four Category 5e Voice and Data Modules in a dedicated bracket for multi-line systems and expanded home networking. Will distribute 24 cables for voice/telephone and/or data networking. Available as a stand-alone unit only. Dimensions 6.25˝h x 13.06˝w x 2.50˝d

Instructions for Use

Telephone Line Distribution Module

• DESCRIPTION
  The Telephone Line Distribution Module (TLDM) is designed to easily fit into Leviton’s Structured Media™ Center to route incoming telephone service throughout the home or office in combinations of 2 to 4 lines for voice applications. Connect a security system to the module via a dedicated Security Port, providing over-ride protection in case of emergency. The TLDM also features a Test Port and Auxiliary Disconnect Port (ADO) allowing the user to test the incoming phone service from one central location.

• PLANNING
  If you wish to connect a security system to the TLDM, see the security section in this instruction sheet prior to wiring the TLDM.

• INSTALLATION
  Connecting the incoming telephone service to the TLDM Run twisted pair cable from the telephone demarcation point to the TLDM, then strip 2 1/2˝ of cable jacket from cable. Each pair of wires corresponds to a line/telephone number (Line 1=blue, Line 2=orange, Line 3=green, Line 4=brown). (Figure 1) Using a professional grade termination tool, punch individual cable pairs down on the 4-pair termination block, labeled “From Demarcation.” (Figure 1 and 2)
  Wire Colors (Figure 2):

  • 1= White/Blue Blue/White
  • 2= White/Orange Orange/White
  • 3= White/Green Green/White
  • 4= White/Brown

NOTE: If you are using the included termination tool, remove excess wire with diagonal cutters or other appropriate wire-cutting tool.

Using the TLDM with the Category 5e Voice and Data Module

Leviton’s TLDM is used in conjunction with the Category 5e Voice and Data Module to connect telephone service to various wall outlets throughout the home or office.

NOTE: Each Category 5e Voice and Data Module connects service to up to 6 wall outlets. Up to four Category 5e Voice and Data Modules can be connected to the TLDM, and can provide service to up to 24 wall outlets with the use of Leviton’s Telephone Expansion Board.

1. Route the Category 5e cable from each wall outlet back to the Category 5e Voice and Data Module. Then, use a punchdown tool to terminate the cable on the Voice and Data Module next to the desired port. (Figure 3)
2. Connect a patch cord from the desired TLDM port to the desired port on the Category 5e Voice and Data Module.

NOTE: A label to the right of each port on the TLDM indicates the lines served.

NOTE: Image does not reflect a connected security system.

Testing Incoming Telephone Service

• To test the incoming telephone service, disconnect the patch cord from the Test Port, which will deactivate the ADO and additional ports. Plug the tester into the Test Port to verify phone service.

Restoring service after testing

1. Connect the 3 1/2˝ 8-position patch cord from the Test Port to the Auxiliary Disconnect Outlet (ADO) Port, creating a bridge between the incoming lines and the distribution ports.

Security Connection

The TLDM features a security port which can be connected to a security system; in an emergency situation, the security port over-rides telephone service to the specified line when an alarm is activated. The security feature may be activated on any one of the 4 terminated lines.

1. Route the desired line pair through the upper left 2-pair termination block. (Figure 4) Then route the line pair to the 4-pair termination block.

NOTE: Should the alarm system be removed from the home, the TLDM must be rewired to restore service to that line. Follow step 1 of the installation instructions.

NOTE: Image illustrates security interface on line 1.

IMPORTANT INSTRUCTIONS

1. Read and understand all instructions. Follow all warnings and instructions marked on the product.
2. Do not use this product near water—e.g., near a tub, wash basin, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
3. Never push objects of any kind into this product through openings, as they may touch dangerous voltages.
4. SAVE THESE INSTRUCTIONS.

SAFETY INFORMATION

1. Never install communications wiring or components during a lightning storm.
2. Never install communications components in wet locations unless the components are designed specifically for use in wet locations.
3. Never touch uninsulated wires or terminals unless the wiring has been disconnected at the network interface.
4. Use caution when installing or modifying communications wiring or components.
5. To prevent electrical shock, each opening must be filled with a module.

2222 – 222nd Street SE Bothell, WA 98021, USA

• Phone: 425-485-4288
• Fax: 425-483-5270

FREQUENTLY ASKED QUESTIONS

What is the Leviton 47603-24P 24-Port Structured Media Panel?

The Leviton 47603-24P is a structured media panel designed to organize and distribute various types of home networking and media equipment.

What is the purpose of a structured media panel?

A structured media panel is used to centralize and manage the distribution of data, voice, and video signals throughout a home or building.

How many ports does the Leviton 47603-24P panel have?

The Leviton 47603-24P panel has 24 ports.

What types of ports are included in the panel?

The panel typically includes a combination of Ethernet ports, coaxial cable ports, and telephone ports.

What size is the Leviton 47603-24P panel?

The panel is designed to fit a standard 19-inch equipment rack.

What materials is the panel made of?

The panel is usually made of sturdy metal or plastic materials.

Can the panel be wall-mounted?

Yes, the Leviton 47603-24P panel can be wall-mounted for installation flexibility.

What kind of installations is the panel suitable for?

The panel is suitable for residential and small commercial installations where centralized networking and media distribution is required.

Does the panel come with wiring diagrams or instructions?

Yes, the panel typically comes with wiring diagrams and installation instructions to guide users through the setup process.

What is the benefit of using a structured media panel in a home?

Using a structured media panel helps keep networking and media equipment organized, reduces cable clutter, and facilitates easier troubleshooting and maintenance.

Can the panel accommodate different types of keystone jacks?

Yes, the panel usually features spaces for keystone jacks, allowing you to customize the types of ports based on your needs.

Is the panel compatible with Leviton's other structured media components?

Yes, Leviton's structured media components are designed to work together, allowing you to build a comprehensive networking and media distribution system.

Are there any accessories available for the Leviton 47603-24P panel?

Yes, Leviton offers various accessories like blank panels, cable management options, and additional port modules for customization.

What is the maximum data transfer speed supported by the Ethernet ports in the panel?

The data transfer speed depends on the specific Ethernet standards used, but the panel is likely to support Gigabit Ethernet (1000 Mbps) or higher.

Can the panel support Power over Ethernet (PoE) devices?

Yes, if the panel has PoE-enabled Ethernet ports, it can support PoE devices like IP cameras, VoIP phones, and wireless access points.

DOWNLOAD THE PDF LINK:Leviton 47603-24P 24PORT STRUCTURED MEDIA PANEL Installation Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>