DYNOJET 2006-2014 Yamaha XV1900 Stratoliner Power Commander Installation Guide
- June 12, 2024
- Dynojet
Table of Contents
POWER COMMANDER 6
Installation Guide for: PC6-22012
Model coverage:
2006-2014 Yamaha XV1900 Stratoliner
2006-2014 Yamaha XV1900 Roadliner
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS
2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
PC6-22012.01
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map| (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fl y between these two
base maps when you hook up a switch to the MAP inputs. You can use any
open/close type switch. The polarity of
the wires is not important.
---|---
Shifter| (Input 1 or 2) Used for clutch-less full throttle upshifts. Insert
the wires from the Dynojet quick shifter into either
Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2
by default.
Speed| Not needed on Harley applications as the speed signal wire is built
into the main wiring harness of the PC6.
Analog| This input is for a 0-5v signal such as engine temp, boost, etc. Once
this input is established you can alter your
fuel curve based on this input in the Power Core software.
Launch| You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged
(continuity) will only allow the RPM to be raised to a certain limit (set in
the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
2 06-14 YAMAHA STRATOLINER/ROADLINER
INSTALLING THE POWER COMMANDER 6
-
Remove the seat.
-
Remove the right hand cosmetic engine cover.
There is a bolt at the front and rear of this cover. -
Lay the PC6 in the area of the ECU.
-
Route the PC6 harness underneath the seat latch plate and under the right hand side of the frame.
-
Route the PC6 harness above the cylinder head following the frame. Route the PC6 harness behind the engine mount bracket.
-
Unplug the WHITE 3-pin connector and the CLEAR6-pin connector.
These connectors are located behind the ignition coils and lead to the throttle bodies. -
Plug the connectors from the PC6 in-line of the stock wiring harness and the throttle bodies.
-
Remove the strap from the ECU and move the ECU out of the way to access the wires underneath.
-
Locate the WHITE 2-pin connector that has a BROWN and a BLACK wire. Remove the blank end of this connection.
4 06-14 YAMAHA STRATOLINER/ROADLINER
INSTALLATION GUIDE -
Plug the RED wire from the PC6 to the stock wiring harness.
-
Reinstall the ECU back into its stock position.
-
Locate the stock ground. Follow the negative battery cable to the frame. Remove the allen bolt that secures the ground cable to the frame.
Reinstall the allen bolt thru the stock ground cable, then thru the ground wire for the PC6 into the frame. -
Use the supplied velcro to attach the PC6 on top of the ECU. Make sure to clean both surfaces with the alcohol swab first.
-
Reinstall the covers and the seat.
Optional inputs:
Speed input – WHITE wire of WHITE 3-pin connector under ECU. Colors of the
wires in this connector are WHITE/BLUE/BLACK.
PC6-22012
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 –
800-992-4993 –
DYNOJET.COM
© 2006-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>