Sagemcom TWX206e FAST 399 Gateway Instruction Manual
- June 12, 2024
- Sagemcom
Table of Contents
Important Information about
the Sagemcom FAST 399 (TWX206e)
INSTALLATION AND SAFE USAGE INSTRUCTIONS
- Place the extender in a vertical orientation on a flat surface.
- Connect the manufacturer supplied AC to DC power adapter. The FAST 399 extender requires the use of a 12VDC, 2.5A power adapter. Only use a manufacturer supplied and approved power adapter and Ethermet cable.
- Connect the “FAST 399″ to the AC Mains in accordance with the installation instructions in this booklet, and the markings on the identification label (voltage, current, and frequency of electricity network).
- Connect the Ethernet cable (provided) to the RJ45 port labeled “LAN” on one end and to the Intemet access device provided by your ISP on the other end.
- For connection of a computer with an Ethernet cable use one of the RJ45 ports on the product marked «1», «2». Then connect the other end of the Ethernet Cable to the Ethernet port of a computer. Repeat as necessary with the other available Ethemet ports.
When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons including the following:
- Do not use this product near water and avoid contact with moisture. For example, does not use near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Care should be taken so that liquids are not spilled on this equipment.
- This equipment is for indoor use only, do not place or install in an outdoor location.
- Place your product on a firm, solid surface, no obstacle at a minimum distance of 44cm(1.44feet). If you put it on something unsteady, it may fall and be damaged. If you place it on a soft surface, such as rug, sofa or cushion, the vents may be blocked, causing the product to overheat.
- Never insert objects into the vents of this equipment as this can result in the risk of electrical shock or fire.
- As the power adapter is the only way to connect to the electrical network, the product must be installed near an easily accessed power outlet.
- This equipment should only be operated with the type of power supply (Voltage and Current) indicated on the marking label.
- Do not overload wall outlets or extension cords. Doing so can result in the risk of fire or electrical shock.
- Avoid blocking any vent openings or exhaust exits on this equipment. Do not place equipment in a built-in installation such as a cabinet that may impede the flow of air through the ventilation openings.
- The equipment should be situated away from heat sources such as radiators, heat registers, stoves, or other heat producing appliances and equipment.
- Care should be taken to ensure that the power cord is routed, so it is not likely to be walked on or pinched by items placed upon or next to it.
- Unplug this equipment before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning only.
- This equipment is not user serviceable and is to be serviced by qualified personnel only. Do not disassemble this equipment. If service is required, disconnect all power from the equipment and consult qualified service personnel.
- To disconnect this equipment from AC power, unplug the power supply from the AC wall socket.
- It is not allowed to connect to public cable distribution or cable television network.
- Use the product in the environment specified as below:
– Air temperature between 0°C (32 F) and +45°C (113 F).
– Relative humidity between 20% and 90%.
– Altitude: 2743 meters (9000feet) maximum.
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
MODIFICATIONS
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to
operate the equipment.
FCC Responsible Party: Sagemcom USA
14651 N. Dallas Parkway
Suite 900
Dallas. TX 75254
Phone: 972-674-4100
RADIO FREQUENCY INTERFERENCE STATEMENT
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device. pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and. if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that intecference will not
occur in a pasticular installation. If this equipment does cause harmful
interference to radio of television reception, which can be determined by
turning the equipment off and on, the user és encouraged to try to correct the
interference by one of more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consutt the dealer or an experienced radio/TV technician for help.
FCC RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located OF Operating
in conjunction with any other antenna or transmitter.
This device produces radio frequency energy in the 2.4GHz. 5GHz and 6GMz
spectrum. The antenna must be positioned to keep a minimum distance of
44cm(1.44feet) from the radiating element to any nearby person.
FCC regulations restrict the operation of this device to indoor use only.
The operation of this device is prohibited on oil platforms, cars. trains.
boats, and aircraft. except that operation of this device is permitted in
large aircraft while flying above 10,000 feet.
Operation of transmitters in the 5.925-7.125 GHz band is prohibited for
control of or Communications with unmanned aircraft systems.
Issued by Sagemcom Broadband SAS.
Sagemcom
250, route de FEmpereur – 92500 RUEIL MALMAISON
FRANCE
© Sagemcom Broadband SAS 2022
All rights reserved. Subject to avadability.
Rights of modifications reserved.
www.sagemcom.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>