Anolis DIVINE 60 UV 180W Full LED Luminaire Instruction Manual
- June 12, 2024
- ANOLiS
Table of Contents
Anolis DIVINE 60 UV 180W Full LED Luminaire
Product Information
Product Name: Divine 60 UV
Manufacturer: ROBE lighting s. r. o.
Address: Palackeho 416, 757 01 Valasske Mezirici, Czech Republic
Contact: Tel.: +420 571 751 500,
E-mail: info@anolis.eu
Website: www.anolislighting.com
Version: 2.0 / 2_2023 Product Usage
Instructions:
Step 1: Cable Gland
1A. For bottom connection, use the cable gland.
1B. For side connection, use the cable gland.
Step 2: Uncover Junction Box
Uncover the junction box located on the bottom side of theluminaire to access
the power and data inlets.
Step 3: Connection
Strip the cable to appropriate lengths for power and data connections. For
power connection, use a 5-cored cable Flamar Li9YC11Y with brown, blue, and
yellow/green wires. For data connection, use shielded cores with white, red,
and shielding wires.
Step 4: Control Menu
Set the control menu inside or outside the junction box as required.
Step 5: Close Junction Box
Close the junction box securely after making the necessary connections.
Step 6: Cable Gland Installation
Use the appropriate wrench size (24 for M20x1.5 or 16 for M12x1.5) to install
the cable gland.
Step 7: Installation
7.A. Installation with Surface Mount Adaptor 1: Apply LOCTITE 5331 paste on
the plastic holder of the cable gland before inserting it into the body of the
gland. Apply LOCTITE 577 paste on the thread of the gland body. Mount the
adaptor using 6 mounting screws. 7.B. Installation with Set of Rubber Feet:
Drill holes on the surface according to hole spacing. Mount Divine using the
mounting holes and rubber feet.
7.C. Installation with C-Clamp Adaptor: Mount a pair of rubber feet using 4
screws. Mount the adaptor using 5 screws.
Step 8: Installation of Accessories
Install the desired accessories such as Adaptor Black Glass, Half Top Hat, Top
Hat, or Wire Guard/Anti-Glare.
INSTALLATION INSTRUCTIONS
1B For side connection
Inlets for power and data from side of the luminaire.
STEP 1
CABLE GLAND
Inlets for power and data from bottom side of the luminaire.
STEP 2
UNCOVER JUNCTION BOX
Uncover junction box located on the bottom side of luminaire.
STEP 3
CONNECTION
Strip these lenghts for cable connections
Connection – colour coding
To connect the Divine 60 UV to mains and a DMX controller, use a 5-cored cable Flamar Li9YC11Y. The 3 colors serve for the power supply and 2 shielded cores are intended for DMX connection.
Power and D ata Connection
Wiring connection (control menu inside)
Wiring connection (control menu outside)
STEP 4
CONTROL MENU
Control menu inside
Set control menu inside junction box.
Control menu outside
Set control menu.
STEP 5
CLOSE JUNCTION BOX
Before applying the torque, make sure the thread is clean and functional.
STEP 6
CABLE GLAND INSTALLATION
Use wrench size 24 for cable gland M20x1.5
Use wrench size 16 for cable gland M12x1.5
Install Cable glands individually!
We recommend to apply an adequate layer of the paste LOCTITE 5331 on the plastic holder of the cable gland before inserting in into the body of the gland and an adequate layer of the paste LOCTITE 577 on the thread ofthe gland body.
Failure to properly install cable glands will result in failure of the water tight seal!
STEP 7.A
INSTALLATION WITH SURFACE MOUNT ADAPTOR
Mount the adaptor using 6 mounting screws.
STEP 7.B
INSTALLATION WITH SET OF RUBBER FEET
Mount pair of rubber feet using 4 screws.
Drill holes to the surface according to holes spacing. Mount Divine via mounting holes on the surface.
STEP 7.C
INSTALLATION WITH C-CLAMP ADAPTOR
Mount the adaptor using 5 screws.
TYPE OF ACCESSORIES
Adaptor Black Glass
Half Top Hat
Top Hat
Wire Guard/Anti-Glare
STEP 8
INSTALLATION OF ACCESSORIES
Unscrew two screws and split accessory to two parts. Place each part onto the luminaire´s head and screw them together.
Secure accessory by 4 screws with spring washer at the back side of the luminaire´s head.
STEP 9
HEAD POSITION ADJUSTMENT
Release locking screw on each sides. Angle fixture to desired position and tighten locking screw on each sides..
- ROBE lighting s. r. o.
- Palackeho 416
- 757 01 Valasske Mezirici
- Czech Republic
- Tel.: +420 571 751 500
- E-mail: info@anolis.eu
- www.anolislighting.com
- VERSION 2.0 / 2_2023
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>