tala LP-WHT-BP-01-EU Linear Triple Pendant Installation Guide
- June 12, 2024
- TALA
Table of Contents
tala LP-WHT-BP-01-EU Linear Triple Pendant
Product Information
The Linear Triple Pendant is a lighting fixture designed in London by Tala. It is a thoughtful lighting solution that is responsibly designed. The light fitting operates on 220-240V mains voltage and is suitable for indoor use only. The SKU for this product is LP-WHT-BP-01-EU. It has an IP20 rating.
The provided components for the Linear Triple Pendant include:
- A Ceiling Bracket (x1)
- A Linear Canopy pre-wired with three Tala Pendants (x1)
- M10 Internal tooth washers (x2)
- Nuts (x2)
- Screws and Rawl Plugs
Product Usage Instructions
Before Starting
Before starting the installation, it is recommended to read the
instructions carefully. The installation of this light fitting should be
performed by a qualified electrician. Ensure that the electricity supply is
switched off at the mains during installation and maintenance. Keep the
instructions for future reference.
Important
-
This light fitting must be connected to the supply earth. If
your lighting circuit does not have an earth, consult a qualified
electrician to provide an earth facility. -
This fitting is suitable for indoor use only.
-
Make sure to follow the current Building Regulations and IEE
Wiring Regulations when installing the fittings.
Recommended Equipment
- Small flat head screwdriver
- Wire strippers
- Insulation tape
- 17mm spanner or adjustable spanner
- Additional equipment may be required for fixing to your
ceiling.
Installation Steps
Step 1: Attach Ceiling Bracket
Using appropriate screws and plugs, attach the Ceiling Bracket (A) to the
ceiling.
Step 2: Attach Linear Canopy
Using the carabiner clips, attach the Linear Canopy (B) to the Ceiling Bracket
(A) and allow it to hang on the suspension cables.
Step 3: Adjust Pendant Cables
Pull the pendant cables (B1) through the cord grips (B2) to your desired
length. Use a flat head screwdriver to tighten the set screws (B3) and secure
them. Tidy the excess cable into the Linear Canopy.
Step 4: Wire the Pendants
If necessary, cut off any excess cable and strip wires to expose the metal
core. Then, re-wire the pendants into the Ceiling Plate, ensuring all double
insulation is maintained.
Step 5: Connect to Mains Electricity
Connect the Ceiling Bracket (A) to the Mains Electricity following the
provided diagram.
Step 6: Install Bulbs
Screw in the bulbs clockwise into the pendants.
Pendant Display Guide
The recommended minimum cord length for all bulbs is 300mm. For different scenarios, the following minimum distances are recommended:
- Scenario 1: Above a kitchen island or bar, or where height is required for standing tasks – Minimum Distance: 800mm
- Scenario 2: Above a coffee or dining table, or where height is required for seated tasks – Minimum Distance: 700mm
- Scenario 3: Above a stairwell or walkway, or where height is required for walking underneath – Minimum Distance: 2.2m (7 Ft)
Care and Cleaning
Refer to the user manual for care and cleaning instructions for the Linear
Triple Pendant.
Installation Guide
LINEAR TRIPLE PENDANT
Thoughtful lighting, responsibly designed in London.
Thank you for making the switch to Tala.
Discover the full Tala family at tala.co.uk
BEFORE STARTING
We recommend the installation of this light fitting is performed by a
qualified electrician. Please read the instructions before commencing work,
and keep them for future reference. Take extreme care when carrying out these
instructions.
IMPORTANT
This light fitting must be connected to the supply earth.
If your lighting circuit does not have an earth, ask a qualified electrician
to provide an earth facility. This light fitting is suitable for indoor use
only. This fitting operates on 220-240V mains voltage. Please visit our
website to see our recommended dimmers.
WARNING
Always switch off electricity supply at the mains during installation and
maintenance. We recommend that the
fuse is withdrawn or the circuit breaker is switched off whilst work is in
progress. Do not just turn off at the wall switch. All fittings must be
installed in accordance with current Building Regulations and IEE Wiring
Regulations.
RECOMMENDED EQUIPMENT
- Small flat head screwdriver
- Wire strippers
- Insulation tape
- 17mm spanner or adjustable spanner
Further equipment may be required for fixing to your ceiling.
Scan me for more technical help
Linear Triple Pendants – Provided Components
- A. x1 Ceiling Bracket
- B. x1 Linear Canopy pre-wired with three Tala Pendants
- C. x2 M10, Internal tooth washer
- D. x2 Nut
- E. Screws and Rawl Plugs
(Always use screws and plugs that are appropriate to the ceiling)
ASSEMBLY
STEP 1
Attach A to the ceiling using screws and plugs. Always choose screws and plugs
that are appropriate for the ceiling.
STEP 2
Using the carabiner clips, attach B t Ao and allow the canopy to hang on the
suspension cables.
STEP 3
Pull pendant cables B1 through cord grips B2 to your desired length. Using a
flat head screwdriver, tighten set screws B3 to secure them.
Tidy the excess cable into the Linear Canopy.
STEP 4
If necessary, cut off excess cable and strip wires to expose the metal core.
Then, re-wire pendants into the Ceiling plate. Maintain all double insulation.
Connect the Ceiling Bracket A to the Mains Electricity as shown
STEP 5
Move B) up onto A and secure using the C and D) as shown.
STEP 6
Screw in bulbs clockwise into the pendants.
PENDANT DISPLAY GUIDE
MINIMUM CORD LENGTH A
For all bulbs shortest recommended cord length is 300mm
PENDANTS – RECOMMENDED CABLE LENGTHS
SCENARIO 1
Above a kitchen island or bar, or where height is required for standing tasks
SCENARIO 2
Above a coffee or dining table, or where height is required for seated tasks
SCENARIO 3
Above a stairwell or walkway, or where height is required for walking
underneath
CARE AND CLEANING
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish of the product. Do not use alcohol or other solvents.
WARRANTY AND AFTER-CARE
This product has a two-year warranty. Within this time we will replace any
parts that have functional defects. please report any faults by emailing:
customerservice@tala.co.uk
This symbol indicates that electrical and electronic equipment (WEEE) should
not be mixed with general household waste. For recovery and recycling, please
take this product to a designated collection point where it will be accepted
free of charge. Many retailers offer this in-store.
Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment.
Join the Community
Instagram: @tala Facebook: talaHQ Pinterest: TalaLED Tag: lighttoliveby
Tala Studios, 25B Vyner Street, London E2 9DG +44 20 3026 3246
hello@tala.co.uk
Tala Europe B.V, Bertus Aafjeshove 40, Nieuwegein 3437JN, Netherlands
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>