Saxby Lighting 98440 Hayden Bollard Light Instruction Manual
- June 12, 2024
- saxby lighting
Table of Contents
Instruction manual
Hayden Bollard
98440
www.saxbylighting.com
98440 Hayden Bollard Light
Thank you for purchasing this light fitting. Please read the instructions
carefully before use to ensure safe and satisfactory operation of this
product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with the IEE Wiring regulations and current Building
Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electrical
supply without your knowledge.
If you are in any doubt, please consult a qualified electrician.
If replacing an existing fitting, make a careful note of the connections.
This light should be connected to a fused circuit.
This product is not suitable for location in or near a marine environment.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will
reach the distances between the junction box and the each light fitting.
Avoid locating any cables in positions that would cause a hazard. Position
cables and outdoor rated junction boxes (not supplied) away from areas where
they may be at risk from being cut, trapped or damaged.
We recommend that you use H07RN-F specification cable (not supplied) which is
an outdoor grade, rubber sheathed cable.
The mains supply cable must have a minimum cross section area of 1.0mm².
Cables must be protected using suitable conduit or plastic trunking.
Take care not to drill into any pipes or mains cables beneath the surface
during mounting holes preparation.
This product must only be installed to a solid, fixed surface, such as
concrete, decking or paving slabs. It must not be installed on soil.
Take care not to drill into any pipes or mains cables beneath the surface
during mounting holes preparation.
Never put anything on the product or hang anything on any part of this
product.
The mounting surface must be able to accommodate the weight / height of the
fitting. If installing on an existing secure (concrete) base, use the holes in
the post base as a template to drill suitable fixing holes and prepare with
suitable ground fixing bolts (not supplied). The supply cable (at least 250mm)
must come out of the mounting surface and directly into the terminal block in
the base / post of the fitting.
Installation
Existing fittings must be completely removed before installation of a new
product. Before removing the existing fitting, carefully note the position of
each set of wires.
Note that the switch is turned off before installation.
Ensure that the screws and cable entry points are sealed to maintain the IP
rating of the product.
After deciding the layout of the light fittings ensure that the cables are
long enough to connect to desired positions.
- Determine the position of your light fitting taking into account the entry position of the cable.
- Place the base of the light fitting over the cable and use it as a template to mark the mounting hole positions and drill the holes to the necessary size and depth, taking care not to damage any concealed pipes or wiring.
- Unscrew the lid and fit the bulb. NOTE: Never fit bulbs of a higher wattage than those specified on the label (as these may cause overheating and damage the fitting).
- Connect the house wiring to the terminal block – see expanded wiring diagram. When you are sure of the connections wrap the Terminal Block and overlap the wiring both sides with 2 layers of insulation tape. NOTE: This is a class 1 fitting and must be earthed.
- Secure the cable clamp over the incoming cable and then push the terminal block assembly fully inside the base.
- Secure the post to the mounting surface making sure that all cables are contained inside the fitting.
- Ensure the rubber seal is in place for ingress protection. Do not overtighten.
- Replace fuse or circuit breaker and switch on. Your light is now ready for use.
Wiring
Having correctly identified the wiring from your existing light fitting, pull the mains wire through the hole and connect to the quick fit connection block inside the product in the following way:
Check that…
You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.
Fitting/replacing bulbs: 1 x Max. 15W E27 GLS
- This fitting has been designed to use energy efficient LED bulbs. Ensure that the minimum distance to the illuminated surface is not less than 0.5m (50cm).
- When changing a bulb, always switch off at the mains and allow the bulb to cool before handling. Dispose of used bulbs carefully. Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting. Use of the incorrect bulb will damage the product and invalidate the guarantee.
Technical data
Supply Voltage: 220-240 V~, 50 Hz
Bulb Type: 1 x Max. 15W E27 GLS (required)
| Conformity with all relevant UKCA Directive requirements.
---|---
| Conformity with all relevant EC Directive requirements.
| This product is Class 1, must be connected to earth.
****| Waste electrical products should not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local Authority
or local store for recycling advice.
| This product is suitable for dimming.
| This product is rated at IP44.
Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive
cleaners as these could damage the finish.
For your safety, always switch off the power supply before changing
lightbulbs, or cleaning.
This LED’s are protected by a PC shade. The shade part must be replaced immediately should it become cracked or damaged. This fitting must not be used without the PC shade in place.
V2 27/04/2022
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
www.saxbylighting.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>