CASAMBI NB.1 LED Controller User Manual
- June 3, 2024
- CASAMBI
Table of Contents
LED Controller
Model: NB.1
4-in-1 Multi-function Model
Advanced Parameters
Full Protection
Introduction
This LED controller is designed to drive single color to RGB+White constant
voltage LED products in voltage range of DC 6-24V . With powerful functions of
Casambi
platform, it also has advanced user parameters to fine tune the application.
With press key, optional RF remote controller and full protection function,
the installation will be simple and reliable.
Function & Size
-
Power supply input
Connect to power supply. The controller can accept supply voltage from DC 6V to 50V, the maximum cable gauge is AWG12 or 2.5mm . The controller’s output voltage is at same level as the power input voltage, please make sure the power supply voltage is correct and the power is capable for the load wattage. The power input ‘+’ unit is directly connected to the output terminal ‘+’ unit inside the controller. -
Press key input
Connect to a normally open type press key switch if local operation is needed. Three operation method is available for the press key:
Single press: Turn on/off.
Double click: Change color or color temperature.
Hold press: Dimming. -
Working status indicator
This indicator shows all working status of the controller. It displays different events as following:
Steady green: Normal working.
Short green blink: Command received.
Green blink for 3 times: Confirmation or identification.
Single yellow flash : Edge of the adjustment.
Red flash: Overload protection.
Yellow flash: Overheat protection. -
LED output
Connect to LED loads. The LED loads must be constant voltage driving type and with common anode connection for multi-channel models. Please make sure the LED rated voltage is same as the power supply and each channel’s maximum load current is in range of the controller’s rated current.
Wiring
Please connect the controller output to LED loads and power supply to the controller power input. The power supply voltage must be same as the LED load’s rated voltage. Check all cables to be well connected and insulated before power on.
This model supports 1-4 channel application from single color to RGB+CCT, please refer to following diagram for multiple application output wiring.
Operation
5. Control by smartphone
Please install CASAMBI app on your smart phone first. It requires iOS10.0,
Android 4.4 or macOS11.0 or later system to support the app. All functions of
the controller is integrated with the CASAMBI app, please find the guidance on
the app for operation.
6. Pair the optional RF remtoe
Besides smart phone and press key control, user can also use the RM05 RF
remote controller to turn on/off and change color or brightness. The remote
controller needs to be paired to controller before using. Please refer to
remote controller’s manual for detailed operation.
Advanced features
7. Change model function
The working mode can be changed from 1 channel (single color) to 4 channels
(RGBW) from the Casambi app.
To change the model, Please make sure the controller is not paired and then
select the ‘Change profile’ function on the app to select desired model.
8. Change user parameters
The press key, RF remote, gradient time and PWM frequency is adjustable from
the user parameter setting. Please go to the setting menu on Casambi app to
set up the parameters.
9. Protection feature
The controller has full protection function against wrong wiring, load short
circuit, overload and overheat. The controller will stop working and the
indicator will flash with red / yellow color to indicate the malfunction. The
controller will try to recover from protection status in a short time when the
working condition is good. For protection issues, please check the situation
with different indicator information:
Red flash: Check the output cables and load, make sure no short circuit and
the load current is in rated range. Also the load must be constant voltage
type.
Yellow flash: Check the installation environment, make sure in a rated
temperature range and with good ventilation or heat dissipation condition.
Specification
Function | Single color, CCT, RGB, RGBW |
---|---|
Working voltage | DC 6-24V |
Rated output current | 4x3A |
Smartphone connection | Bluetooth mesh |
Press key function | Yes |
RF remote fucntion | Yes |
RF remote frequency | 433.92MHz |
Output mode | PWM constant voltage |
User parameter | Press key, Remote enable, Gradient, PWM frequency |
PWM frequency | 500Hz, 1KHz, 2KHz, 4KHz |
Overload protection | Yes |
Overheat protection | Yes |
Working temperature (Ta) | -20°C~+55°C |
Dimension | 87x24x15mm |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>