JLAB Jbuds Band Neckband Headset User Manual

June 6, 2024
JLab

JLAB Jbuds Band Neckband Headset User Manual
JLAB Jbuds Band Neckband Headset

FIRST TIME SETUP: BLUETOOTH PAIRING

  1. Turn on the Bluetooth in your device settings.
    BLUETOOTH PAIRING

  2. Press and hold button for 10 seconds. Release.
    Light will blink red and blue to indicate pairing mode.
    BLUETOOTH PAIRING

  3. Select “JLab JBuds Band” in your device’s Bluetooth settings to connect.
    Light will slow blink blue when Bluetooth is paired.
    BLUETOOTH PAIRING

RECURRING USE

Once JLab JBuds Band has initially paired to your device, the earbuds will auto-connect to your Bluetooth device when powered back ON. (Follow BUTTON FUNCTIONS instructions)

BUTTON FUNCTIONS

VOLUME UP: Click once
TRACK FORWARD: Click & hold 2+ seconds
POWER ON / OFF: Click & hold 2 seconds
PLAY / PAUSE
ANSWER / HANG UP CALLS: Click once
REJECT INCOMING CALLS: Click & hold 1 second
ACTIVATE SIRI (iOS) OR
“OK GOOGLE” (ANDROID): Click twice
BLUETOOTH PAIRING: (Follow First Time Setup: Bluetooth Pairing)
VOLUME DOWN: Click once
TRACK BACKWARD: Click & hold 2+ seconds
BUTTON FUNCTIONS

EQUALIZER MODES

Quick press both buttons for different EQ settings (JBuds Band will cycle 3 EQ settings)

JLab SIGNATURE (One Beep) JLab C3™ signature sound with amplified vocals and bass

BALANCED (Two Beeps) Even sound with no additional sound enhancements

BASS BOOST (Three Beeps) Amplified bass and sub-bass

VOICE PROMPTS

“HELLO” Power is ON.
“BATTERY FULL” = 100-75%
“BATTERY MEDIUM” = 75-25%
“LOW BATTERY” = Less than 25%
“READY TO PAIR” JLab JBuds Band headset is ready to connect to your Bluetooth device.
“YOU’RE CONNECTED” JLab JBuds Band headset is connected to your Bluetooth device and ready for use.
“GOODBYE” Power turning OFF.

CHARGING

  1. Open USB door and connect the cable to a computer or USB power source to charge.
    CHARGING

  2. Light will turn solid red when charging and turn blue when fully charged.
    CHARGING

FITTING

  1. Choose ear tip size.
    FITTING

  2. Move the earbud to desired location from the Adjustable Tip Placement.
    FITTING

  3. Rest the band around the neck with the controls facing the right hand side.
    FITTING

CONNECTION TROUBLESHOOTING

I DO NOT SEE JLAB JBUDS BAND IN MY DEVICE

  1. Turn Bluetooth off and then back on in device settings.
    CONNECTION

  2. If you still do not see JLab JBuds Band, repeat FIRST TIME SETUP: BLUETOOTH PAIRING directions.
    CONNECTION

JLAB JBUDS BAND DOES NOT RECONNECT TO MY DEVICE AFTER POWERING ON

  1. In device settings, forget JLab JBuds Band.
    CONNECTION

  2. Turn Bluetooth off then back on in device settings.
    CONNECTION

  3. Repeat  FIRST TIME SETUP: BLUETOOTH PAIRING directions.
    CONNECTION

BLUETOOTH IS CONNECTING TO AN UNWANTED DEVICE

Note: The JLab JBuds Band can remember up to 8 devices. It will try to auto-connect to last device used.

  1. If you have more than one device that was connected to JLab JBuds Band, turn OFF Bluetooth on unwanted devices and turn ON Bluetooth on chosen device.
    CONNECTION

  2. Press and hold button for 10 seconds. Release.
    Light will blink red and blue to indicate pairing mode.
    Select “JLab JBuds Band” in your device settings to connect.
    Light will slow blink blue when Bluetooth is paired.
    CONNECTION

WARNING

Make sure USB door is closed and fastened.
This will protect against sweat and water damage.
USB door

Before charging, JLab JBuds Band headset needs to be fully dry.
If there is any exposure to moisture, the internal components may become damaged. It is best practice to air dry before charging.
USB door

CAUTIONS

  • Avoid getting moisture or liquids into the tip of the earbuds or charging port.
  • Avoid extreme heat, cold, and humidity.
  • Avoid dropping or crushing the earbuds, stressing the cable by rapid pulling or extreme force, or bending the cable at a sharp angle.
  • Wax may build up in the earbud tips, lowering the sound quality. Carefully remove the wax with a cotton swab or other small tool to improve the sound quality.
  • If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
  • If you experience regular discomfort while using this product, discontinue use and consult your physician.
  • We recommend you treat your earbuds as you would a nice pair of sunglasses and keep them in safe location when not in use.

Shop productsShop products | Product alerts | Burn-in your headphones

JLab Audio + Burn-in Tool
Apple Store Icon

We love that you are rocking JLab Audio!
We take pride in our products and fully stand behind them.

YOUR WARRANTY

WARRANTY All warranty claims are subject to JLab Audio authorization and at our sole discretion. Retain your proof of purchase to ensure warranty coverage.

CONTAC$T US

CONTACT US Reach out to us at support@jlabaudio.com
or visit jlabaudio.com/contact

REGISTER TODAY

jlabaudio.com/register

Product updates | How-to tips
FAQs & more

Company Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals