Indesit TIAA 12 V.1 2-DOOR Fridge-Freezer Operating Instructions

Indesit TIAA 12 V.1 2-DOOR Fridge-Freezer

Assistance

Before calling for Assistance:

• Check if the malfunction can be solved on your own (see Troubleshooting).
• If after all the checks, the appliance still does not operate or the problem persists, call the nearest Service Centre

Communicating:

• type of malfunction
• appliance model (Mod.)
• serial number (S/N)

This information can be found on the data plate located on the bottom left side of the refrigerator compartment. Never call on unauthorized technicians and always refuse spare parts which are not originals.

Description of the appliance

Overall view

The instructions contained in this manual are applicable to different model refrigerators. The diagrams may not directly represent the appliance purchased. For more complex features, consult the following pages.

1. Leveling FEET
2. FRUIT and VEGETABLE bin
3. SHELVES*
4. TEMPERATURE REGULATING Knob
5. PURE WIND*
6. FREEZER and STORAGE compartment
7. Removable multipurpose SHELVES*
8. BOTTLE shelf

Assembling the Freestanding Fridge-Freezer

The steps are shown in the following:

Reversible doors

Installation

• Before placing your new appliance into operation please read these operating instructions carefully. They contain important information for safe use, installation, and for care of the appliance.
• Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance.

Positioning and connection

Positioning

1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and condenser give off heat and require good ventilation to operate correctly and save energy.
3. Leave a space of at least 10 cm between the top part of the appliance and any furniture above it, and at least 5 cm between the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat (direct sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the appliance and the wall behind it, fit the spacers supplied in the installation kit, following the instructions provided.

Levelling

1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator by tightening or loosening the front feet.

Electrical connections

After the appliance has been transported, carefully place it vertically and wait at least 3 hours before connecting it to the electricity mains.

Before inserting the plug into the electrical socket ensure the following:

• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the appliance, which is indicated on the data plate located on the bottom left side of the fridge (e.g. 150 W).
• The voltage must be in the range between the values indicated on the data plate located on the bottom left side (e.g. 220-240V).
• The socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorized technician to replace it (see Assistance). Do not use extension cords or multiple sockets.
  • Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible.
  • The cable must not be bent or compressed.
  • The cable must be checked regularly and replaced by authorized technicians only (see Assistance).
  • The manufacturer declines any liability should these safety measures not be observed.

Start-up and use

Starting the appliance

• Before starting the appliance, follow the installation instructions (see Installation).
• Before connecting the appliance, clean the compartments and accessories well with lukewarm water and bicarbonate.

1. Insert the plug into the socket and ensure that the internal light illuminates.
2. Turn the TEMPERATURE ADJUSTMENT knob to an average value. After a few hours, you will be able to put food in the refrigerator.

Setting the temperature

The temperature inside the refrigerator compartment automatically adjusts itself according to the position of the TEMPERATURE

• ADJUSTMENT knob.
• 1 = warmest 5 = coldest

We recommend, however, a medium position. The cooling section of the refrigerator is located inside the back wall of the refrigerator compartment for increased space and improved aesthetics. During operation, the back wall will be covered in frost or water droplets depending on whether the compressor is operating or paused. Do not worry, the refrigerator is functioning normally. If the TEMPERATURE ADJUSTMENT knob has been set on high values with large quantities of food and with a high ambient temperature, the appliance can operate continuously, resulting in excessive frost formation and excessive energy consumption: compensate for this by shifting the knob towards lower values (defrosting will occur automatically). In static appliances, the air circulates in a natural way: the colder air tends to move downwards as it is heavier.

The food should be stored as follows:

• Food  Arrangements inside the refrigerator
• Fresh fish and meat  Above the fruit and vegetable bins
• Fresh cheese  Above the fruit and vegetable bins
• Cooked food  On any shelf
• Salami, loaves of bread, and chocolate  On any shelf
• Fruit and vegetables  In the fruit and vegetable compartment bins
• Eggs  On the shelf provided
• Butter and margarine  On the shelf provided
• Bottles, drinks, and milk  On the shelves provided

PURE WIND

It is recognizable due to the presence of the mechanism on the top part of the refrigerator compartment (see diagram).

Pure Wind maximizes air circulation, improving the efficiency of the evaporator and helping to achieve the optimal temperature inside the refrigerator as quickly as possible each time it has been opened. The blown air (A) is cooled when it comes into contact with the cold wall, whereas the hotter air (B) is sucked up (see diagram). Pure Wind Plus products are also equipped with a filter which, thanks to the inclusion of silver ions, makes it possible to reduce bacteria by 70% and to eliminate odors inside the refrigerator unit, thereby guaranteeing improved food storage. If the TEMPERATURE ADJUSTMENT  knob has been set on high values with large quantities of food and with a high ambient temperature, the appliance can operate continuously, resulting in excessive frost formation and excessive energy consumption: compensate for this by shifting the knob towards lower values (defrosting will occur automatically).

Using the refrigerator to its full potential

• Place only cold or lukewarm foods in the compartment, not hot foods (see Precautions and tips).
• Remember that cooked foods do not last longer than raw foods.
• Do not store liquids in open containers. They will increase humidity in the refrigerator and cause condensation to form.

SHELVES:  with or without a grill.

Due to the special guides, the shelves are removable and the height is adjustable (see diagram), allowing easy storage of large containers and food. Height can be adjusted without complete removal of the shelf.

TEMPERATURE  Indicator light: to identify the coldest area in the refrigerator.

1. Check that  OK  appears clearly on the indicator light (see diagram).
2. If the word “ OK ” does not appear it means that the temperature is too high: adjust the  REFRIGERATOR   OPERATION  knob to a higher ( colder ) position and wait approximately 10 hours until the temperature has stabilized.
3. Check the indicator light again: if necessary, readjust it following the initial process. If large quantities of food have been added or if the refrigerator door has been opened frequently, it is normal for the indicator not to show  OK. Wait at least 10 hours before adjusting the  REFRIGERATOR OPERATION  knob to a higher setting.

Using the freezer to its full potential

• Do not re-freeze food that is defrosting or that has already been defrosted. These foods must be cooked and eaten ( within   24   hours ).
• Fresh food that needs to be frozen must not come into contact with food that has already been defrosted. Fresh food must be stored above the grill in the freezer compartment and if possible be in direct contact with the walls ( side  and  rear ), where the temperature drops below -18°C and guarantees rapid freezing.
• Do not place glass bottles that contain liquids, and which are corked or hermetically sealed in the freezer because they could break.
• The maximum quantity of food that may be frozen daily is indicated on the plate containing the technical properties located on the bottom left side of the refrigerator compartment ( for example Kg/24h: 4 ) Do not open the door during freezing.
• If there is a power cut or malfunction, do not open the freezer door. This will help maintain the temperature inside the freezer, ensuring that foods are conserved for at least 9 -14 hours.
• If the room temperature drops below 14°C for an extended period of time, the ideal temperature will not be reached in the freezer compartment and food preservation will be reduced.

Maintenance and care

Switching the appliance off

• During cleaning and maintenance, it is necessary to disconnect the appliance from the electricity supply. It is not sufficient to set the temperature adjustment knobs on (appliance off) to eliminate all electrical contact.

Cleaning the appliance

• The external and internal parts, as well as the rubber seals, may be cleaned using a sponge that has been soaked in lukewarm water and bicarbonate of soda or neutral soap. Do not use solvents, abrasive products, bleach, or ammonia.
• The removable accessories may be soaked in warm water and soap or dishwashing liquid. Rinse and dry them carefully.
• The back of the appliance may collect dust which can be removed by delicately using the hose of a vacuum cleaner set on medium power. The appliance must be switched off and the plug must be pulled out before cleaning the appliance.

Avoiding mold and unpleasant odors

• The appliance is manufactured with hygienic materials which are odor free. In order to maintain an odor-free refrigerator and to prevent the formation of stains, food must always be covered or sealed properly.
• If you want to switch the appliance off for an extended period of time, clean the inside, and leave the doors open.

Defrosting the appliance

Follow the instructions below.
Do not speed up the defrosting process by using any devices or tools other than the scraper provided, you may damage the refrigeration circuit.

Defrosting the refrigerator compartment

The refrigerator has an automatic defrosting function: water is ducted to the back of the appliance by a special discharge outlet (see diagram) where the heat produced by the compressor causes it to evaporate. It is necessary to clean the discharge hole regularly so that the water can flow out easily. The refrigerator has an automatic defrosting function: water is ducted to the back of the appliance by a special discharge outlet (see diagram) where the heat produced by the compressor causes it to evaporate. It is necessary to clean the discharge hole regularly so that the water can flow out easily.

Defrosting the freezer compartment

If the frost layer is greater than 5 mm, it is necessary to defrost manually:

1. Set the TEMPERATURE ADJUSTMENT knob to the position.
2. Wrap frozen foods in newspaper and place them in another freezer or in a cool place.
3. Leave the door open until the frost has melted completely. This can be made easier by placing containers with lukewarm water in the freezer compartment.
4. Clean and dry the freezer compartment carefully before switching the appliance on again.
5. Wait for approximately 2 hours, i.e. until the ideal storage conditions have been restored, before placing food in the freezer compartment.

Replacing the light bulb

To replace the light bulb in the refrigerator compartment, pull out the plug from the electrical socket. Follow the instructions below. Access the light bulb by removing the cover as indicated in the diagram. Replace it with a similar light bulb within the power range indicated on the cover (15W or 25W).

Precautions and tips

The appliance was designed and manufactured in compliance with international safety standards. The following warnings are provided for safety reasons and must be read carefully.

This appliance complies with the following Community Directives:

• 73/23/EEC of 19/02/73 (Low Voltage) and subsequent amendments;
• 89/336/EEC of 03.05.89 (Electromagnetic Compatibility) and subsequent amendments;
• 2002/96/CE

General safety

• The appliance was designed for domestic use inside the home and is not intended for commercial or industrial use.
• The appliance must be used to store and freeze food products by adults only and according to the instructions in this manual.
• The appliance must not be installed outdoors, even in covered areas. It is extremely dangerous to leave the appliance exposed to rain and storms.
• Do not touch the appliance with bare feet or with wet or moist hands and feet.
• Do not touch the internal cooling elements: this could cause skin abrasions or frost/freezer burns.
• When unplugging the appliance always pull the plug from the mains socket, do not pull on the cable.
• Before cleaning and maintenance, always switch off the appliance and disconnect it from the electrical supply. It is not sufficient to set the temperature adjustment knobs on (appliance off) to eliminate all electrical contact.
• In the case of a malfunction, under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or further malfunctioning of the appliance.
• Do not use any sharp or pointed utensils or electrical equipment – other than the type recommended by the manufacturer – inside the frozen food storage compartments.
• Do not put ice cubes taken directly from the freezer into your mouth.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• Keep packaging material out of the reach of children! It can become a choking or suffocation hazard.

Disposal

• Observe local environmental standards when disposing of packaging material for recycling purposes.
• The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed-out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliances.
• Respecting and conserving the environment
• Install the appliance in a fresh and well-ventilated room. Ensure that it is protected from direct sunlight and do not place it near heat sources.
• Try to avoid keeping the door open for long periods or opening the door too frequently in order to conserve energy.
• Do not fill the appliance with too much food: cold air must circulate freely for food to be preserved properly. If circulation is impeded, the compressor will work continuously.
• Do not place hot food directly into the refrigerator. The internal temperature will increase and force the compressor to work harder and will consume more energy.
• Defrost the appliance if ice forms (see Maintenance). A thick layer of ice makes cold transference to food products more difficult and results in increased energy consumption.
• Regularly check the door seals and wipe them clean to ensure they are free of debris and to prevent cold air from escaping (see Maintenance).

Troubleshooting

If the appliance does not work, before calling for Assistance (see Assistance), check for a solution from the following list.

The internal light does not illuminate.

• The plug has not been inserted into the electrical socket, not far enough to make contact, or there is no power in the house.

The refrigerator and the freezer do not cool well.

• The doors do not close properly or the seals are damaged.
• The doors are opened too frequently.
• The  TEMPERATURE   ADJUSTMENT  knob is not in the correct position.
• The refrigerator or the freezer has been overfilled.
• The atmospheric temperature of the area surrounding the appliance is lower than 14°C.
• The food inside the refrigerator is beginning to freeze.
• The  TEMPERATURE   ADJUSTMENT  knob is not in the correct position.
• The food is in contact with the back inside the wall of the refrigerator.

The motor runs continuously.

• The door is not closed properly or is continuously opened.
• The outside ambient temperature is very high.
• The thickness of the frost exceeds 2-3 mm (see Maintenance).

The appliance makes a lot of noise.

• The appliance has not been installed on a level surface (see Installation).
• The appliance has been installed between cabinets that vibrate and make noise.
• The internal refrigerant makes a slight noise even when the compressor is off. This is not a defect, it is normal.

Some of the external parts of the refrigerator become hot.

• These raised temperatures are necessary in order to avoid the formation of condensation on certain parts of the product.

The back wall of the refrigerator unit is covered in frost or droplets of water

• This shows the appliance is operating normally.

There is water at the bottom of the refrigerator.

• The water discharge hole is blocked (see Maintenance).

FAQ’s

If I want my fridge-freezer to be colder, should I choose a higher or lower setting?****

With most fridge freezers, a higher setting means the machine will cool harder. With a lower setting, the machine will cool less hard and the temperature in the fridge-freezer will be higher.

Can I change the opening direction of the door of my fridge-freezer?****

Yes, nearly all standing fridge freezers offer the option to place the door on the other side. How to do this can generally be found in the manual.

What is the best temperature setting for a refrigerator?****

From a health perspective temperatures between 3℃ and 4℃ are the best. At these temperatures the growth of bacteria and mold is limited.

The drain hole in my fridge-freezer is dirty/clogged, how do I clean it?****

There are special cleaning devices to do this, but it is also possible to remove blockage or dirt with a cotton swab. To keep the drain hole clean and prevent smells it is advisable to put a drop of chlorine bleach in the drain 4 times a year.

How often should I defrost my freezer?****

For optimal use of the freezer it is best to defrost it once every 3-6 months. Ice on the inside of the freezer reduces the available space and increases the use of energy. The thawing process can be accelerated by placing hot water in the drawer or placing bowls of hot water in the freezer.

My fridge-freezer makes a bubbling sound, is that normal?****

Modern fridge-freezers make use of an environmentally friendly cooling agent. During the cooling process, this substance turns into a gas, which can cause a bubbling and/or hissing sound. This is perfectly normal.

I bought a new fridge-freezer, can I turn it on immediately?****

No, the fridge freezer needs to stand in an upright position for at least 4 hours before it can be turned on. This is because the coolant liquid needs to settle.

Is it normal that water or ice drops are forming on the back wall of my fridge freezer?****

Yes, this is a completely normal phenomenon. The moisture that enters the fridge freezer with warm air or products will settle on the coldest part, being the back wall. Because the back wall can reach temperatures below freezing, the drops will freeze from time to time. When the fridge freezer is idle the drops will thaw and flow to the drain of the fridge freezer.

De door of my fridge-freezer will not close properly, why is that?****

The two most common causes are that the fridge-freezer is not level and that the door seal is damaged or has food remains on it. Make sure the fridge- freezer is level and check the door seal. Replace the seal if necessary.

How much space should I leave between my fridge-freezer and the wall?****

To ensure good ventilation it’s best to leave at least 5cm of free space on both sides and the back of the fridge-freezer.

What do the stars on the freezer mean?****

The stars indicate the freezing capacity. 1 star indicates a freezing capacity down to -6ºC. This makes the freezer suitable for making ice cubes or storing previously frozen goods for up to two weeks. Fresh food cannot be frozen. 2 stars indicates a freezing capacity down to -12ºC. This makes the freezer suitable for storing previously frozen goods for up to two months. Fresh food cannot be frozen. 3 stars indicate a freezing capacity down to -18ºC. This makes the freezer suitable

How long does it take for my refrigerator to reach the set temperature after I turn it on?****

This depends on the size, age and model of the refrigerator. It may take several hours to 24 hours for the refrigerator to reach the set temperature. The process can be accelerated by placing non-perishable goods in the refrigerator. The temperature in the refrigerator cannot be measured properly by feeling the air inside. The best way to tell if the refrigerator has reached the set temperature is to place a glass of water in the refrigerator with a thermometer in it.

There is condensation in my refrigerator, why is that?****

There can be several causes. The door gasket can be defective, allowing outside air into the refrigerator. It’s also possible that the refrigerator is not level, preventing the door from closing correctly. Another cause is a large difference between the temperature inside the refrigerator and outside while the door is being opened frequently.

Can I put warm food or drinks in my fridge freezer?****

Preferably not. The temperature in your fridge-freezer will rise, which negatively impacts the other items that are stored inside.

There is mold on the rubber seals of my fridge-freezer, what should I do?****

The rubber seals are not actually inside the fridge-freezer and are therefore warmer. This allows bacteria to grow and mold to form. Clean the rubbers regularly to prevent this.

What is R-410A?****

R-410A is a cooling agent that is used in appliances that cool up to 0°C, like refrigerators and air conditioners. It is the replacement of older cooling agents and does not damage the ozone layer.

Download this PDF Link:Indesit TIAA 12 V.1 2-DOOR Fridge-Freezer Operating Instructions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>