Dynojet PC6-17088 Power Commander 6 Fuel Injection Module Installation Guide

POWER COMMANDER 6
Install guide for: PC6-17088
Model coverage:
2020-2021 Kawasaki Ninja 1000 SX

PARTS LIST

1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS
2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
PC6-17088.01

INPUT ACCESSORY GUIDE

OPTIONAL ACCESSORY INPUTS

Map (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can use any open/close type switch. The polarity of the wires is not important.
Shifter (Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2 by default.
Speed If your application has a speed sensor then you can tap into the signal side of the sensor and run a wire into this input. This will allow you to calculate gear position in the Control Center Software. Once gear position is setup you can alter your map based  on gear position and setup gear dependent kill times when using a quickshifter. .
Analog This input is for a 0-5v signal such as engine temp, boost, etc. Once this input is established you can alter your fuel curve based on this input in the Power Core software. Launch You can connect a wire to either Input 1 or Input 2 and then the other end to a switch. This switch when engaged (continuity) will only allow the RPM to be raised to a certain limit (set in the software). When released, you will have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of the unit and loosen the screw for the corresponding input. Using a 22-24 gauge wire, strip about 10mm from its end. Push the wire into the hole of the PC6 until it stops and then tighten the screw. Make sure to reinstall the rubber plug.
NOTE: If you tin the wires with solder it will make inserting them easier.

2 20-21 KAWASKI NINJA 1000

INSTALLING THE POWER COMMANDER 6

1. Remove the seat, fuel tank and airbox.

2. Store the PC6 module next to the battery.
   The supplied velcro can be used to secure the module.
   Clean surfaces with the alcohol swab before attaching the velcro.

3. Route the harness towards the front of the bike along the left side of the frame.

4. Unplug the stock wiring harness from each injector

5. Plug the PC6 wiring harness in-line of the stock wiring harness and each fuel injector.
   PC6 harness:
   ORANGE – cylinder #1 (left)
   YELLOW – cylinder #2
   GREEN – cylinder #3
   BLUE – cylinder #4 (right)

6. Attach the ground wire from the PC6 to the common stock ground wire location.
   This is located in front of the battery underneath the rubber flap.

7. Locate and unplug the Throttle Position Sensor on the right hand side of the throttle bodies.

8. Plug the PC6 harness in-line of the stock wiring harness and the TPS.

9. Reinstall the airbox, fuel tank and bodywork.

4 20-21 KAWASKI NINJA 1000

PUSH THE LIMIT

2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 –800-992-4993
DYNOJET.COM
© 2019-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED

Documents / Resources

| Dynojet PC6-17088 Power Commander 6 Fuel Injection Module [pdf] Installation Guide
PC6-17088, PC6-17088 Power Commander 6 Fuel Injection Module, Power Commander 6 Fuel Injection Module, Commander 6 Fuel Injection Module, 6 Fuel Injection Module, Injection Module, Module
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>