heatit 45 125 99 Z-HAN2 Z-Wave HAN Sensor User Guide
- June 12, 2024
- HEATIT
Table of Contents
heatit 45 125 99 Z-HAN2 Z-Wave HAN Sensor
Product Information
- Product Name: Heatit Z-HAN2
- Article Number: 45 125 99
- Doc. Version: 2023-A
- Doc. Date: 01.06.2023
The Heatit Z-HAN2 is a Z-WaveTM HAN sensor designed for AMS meters (Smart meters). It works with HAN ports and is equipped with an RJ45 port for connecting to the AMS meter. The device can be powered through the RJ45 port by most AMS meters, but it also has a 5V micro USB input for external power supply.
Please note that installation must be done by a qualified electrician in accordance with national building codes. Before installation, disconnect the power to the device from the mains. During installation, power to the device must be disconnected at all times.
Product Usage Instructions
- Contact your energy company to activate your HAN-port.
- Connect power to the Z-HAN2 using a micro USB cable.
- Set the primary controller to add mode(security/non-security).
- Press the reset button on the device three times in a rapid sequence. This will include the Heatit Z-HAN2 in your Z-Wave network.
- Open your main fuse box.
- Plug the RJ45 cable into the energy meter and the Z-HAN2.
Note: Before installation, make sure to read the primary controller manual for instructions on how to set the primary controller in add/remove mode. The device can only be added or removed from the network if the primary controller is in add/remove mode. When the device is removed from the network, it will not revert to factory settings.
Standard (Manual) Add/Remove Mode:
- To start the configuration process, press the reset button on the device three times in rapid sequence. The LED will blink greenfor 90 seconds indicating add/remove mode.
- If successful, the LED will light up in solid green for 3 seconds.
- If unsuccessful, the LED will light up in solid red for 3 seconds.
SmartStart (Automatic) Mode:
If your primary controller supports SmartStart inclusion, you can add the Heatit Z-HAN2 to a Z-Wave network by scanning the Z-Wave QR-Code on the product. No further action is required, and the device will be added automatically after being powered on within range of the primary controller.
LED Patterns:
- During add/remove mode: Blinking green LED
- If successful: Solid green LED for 3 seconds
- If unsuccessful: Solid red LED for 3 seconds
INTRODUCTION
Heatit Z-HAN2 is a Z-Wave™ HAN sensor for AMS meters (Smart meters). Heatit
Z-HAN2 works with HAN ports.
The Heatit Z-HAN 2 is equipped with an RJ45 port for connecting the AMS meter.
The Heatit Z-HAN2 can be powered through the RJ45 port by most AMS meters, but
it also has a 5V micro USB input for external power supply.
STATEMENT REGARDING PRODUCTS FROM MULTIPLE MANUFACTURERS
Please read this before installation
This device may be used with all devices certified with the Z-Wave Plus™
certificateand should be compatible with such devices produced by any
manufacturer. Every primary controller is different depending on the
manufacturer, their target audience and intended use/application. Please
review the functionalities implemented by the primary controller you intend to
use with our Z-Wave Plus certified device to ensure that it provides the
necessary controls to take full advantage of our product’s capabilities.
INSTALLATION
Installation must be done by a qualified electrician in accordance with national building codes. Before installation, disconnect the power to the device from the mains. During installation of the device, power to the device must be disconnected AT ALL TIMES!
QUICK START
- Contact your energy company to activate your HAN-port.
- Connect power to the Z-HAN2 with a micro USB cable.
- Set the primary controller to add mode (security/non- security).
- Press the reset button 3 times in a rapid sequence. Heatit Z- HAN2 is now included in your Z-Wave network.
- Open your main fuse box.
- Plug the RJ45 cable into the energy meter and the Z-HAN2.
ADD/REMOVE
Please read this before installation
The primary controller/gateway has a mode for adding or removing devices.
Please refer to your primary controller manual on how to set the primary
controller in add/remove mode. The device may only be added or removed from
the network if the primary controller is in add/remove mode. When the device
is removed from the network, it will NOT revert to factory settings.
An always listening node must be powered continuously and reside in a fixed
position in the installation to secure the routing table. Adding the device
within a 2 meters range from the gateway can minimize faults during the
Interview process.
There are two ways to add the device to a Z-Wave network.
Standard (Manual)
Add/remove mode is indicated on the device by a blinking green LED. It
indicates this for 90 seconds until a timeout occurs, or until the module has
been added to/removed from the network. Configuration mode can also be
cancelled by performing the same procedure used for starting Configuration
mode.
To start the configuration process, press the reset button 3 times in rapid
sequence. The LED will light up in solid green for 3 seconds if add/remove is
successful. The device is now ready for use with default settings.
NB! When the device is removed from the gateway, the parameters are not reset.
To reset the parameters, see ”Factory reset”.
If inclusion fails, please perform a ”remove device” process and try again. If
inclusion fails again, please see “Factory reset”.
SmartStart (Automatic)
SmartStart enabled products may be added to a Z-Wave network by scanning the
Z-Wave QR-Code on the product
if your primary controller supports SmartStart inclusion. No further action is
required, and the SmartStart product will be added automatically after being
powered on within range of the primary controller.
LED-PATTERNS
When device enters add/remove mode the LED will blink green. If successful,
the LED will light up in solid green for 3 seconds. If unsuccessful, the LED
will light up in solid red for 3 seconds.
FACTORY RESET
Press and hold the configuration button. After 3 seconds the LED will start to
blink green. After 20 seconds the LED will start blinking green rapidly. You
may now release the button. If reset was successful, the LED will light up in
solid green for 3 seconds
Please use this procedure only when the network primary controller is missing
or otherwise inoperable.
FEATURES
TECHNICAL DATA
- Protocol Z-Wave, 868.4MHz
- Chip Z-Wave 800 chip
- Rated voltage 5V DC
- Ambient temperature 5°C to 40°C
- Humidity 10% til 85% RH
- Range RF Min. 40 meters
- IP Code IP20
- Size (LxWxH) 80 x 31 x 22mm
- Approvals Z-Wave Plus v2, CE
MAINTENANCE
The product is maintenance-free. Indoor use only.
We have designed this product in accordance with our strict quality requirements (ISO 9001) and environmental requirements (ISO 14001). All electrical installations must be carried out by a authorized electrical installer. The product must be installed in accordance with our installers manual and national building codes. Any wrongful installation, misuse, damage of the product, is not covered under warranty. Heatit Controls AB can not be held liable for any type of errors or omittances in our product information. Product specifications may change without further notice.
Heatit Controls AB l Läkarvägen 4, 454 31 BRASTAD, SWEDEN
Phone: +47 61 18 77 77 l post@heatit.com –
www.heatit.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>