ZENEC ZE-RCE3701-MK2-S Rear View Camera for Fiat Ducato Instruction Manual
- June 13, 2024
- ZENEC
Table of Contents
ZENEC ZE-RCE3701-MK2-S Rear View Camera for Fiat Ducato
Product Information
The ZE-RCE3701-MK2-S is a rear view camera designed specifically for use with FIAT Ducato III vehicles and motor homes. It is equipped with high-quality components to ensure reliable performance and durability.
Technical Specifications:
- Image device: [Image device]
- Lens focal length: [Lens focal length]
- TV system: [TV system]
- View angle: [View angle]
- Native sensor resolution: [Native sensor resolution]
- Resolution of video-out: [Resolution of video-out]
- Frame rate: [Frame rate]
- Signal to noise ratio: [Signal to noise ratio]
- Light sensitivity: [Light sensitivity]
- Video output: [Video output]
- White balance: [White balance]
- Backlight compensation: [Backlight compensation]
- Gamma correction: [Gamma correction]
- Gain control: [Gain control]
- Sync system: [Sync system]
- Power supply: [Power supply]
- Current consumption: [Current consumption]
- IP protection rating: [IP protection rating]
- Operating temperature: [Operating temperature]
Key Features:
- [Key feature 1]
- [Key feature 2]
- [Key feature 3]
Cautions:
Use only the included connection cable. Altering or replacing it will void the warranty. While the camera is water- and dustproof, high-pressure water and steam jet devices used for vehicle cleaning may still damage IP69K rated camera models. Maintain a distance of at least one meter between the water nozzle and the camera housing.
Manufacturer Information:
ZENEC by ACR AG
Bohrturmweg 1 CH-5330 Bad Zurzach Switzerland EU Legal Representative: ACR S &
V GmbH Industriestr. 35 D-79787 Lauchringen Germany
Website: www.zenec.com
Product Usage Instructions
- Loosen the two Phillips cross recess screws to remove the brake light reflector housing.
- Un-connect the white system plug of the vehicle from the brake light reflector housing.
- Screw in and tighten the stainless steel mounting bolts by hand (5Nm) and use a dab of Loctite if possible.
- Route the main cable from the infotainer in the vehicle cockpit/dashboard to the brake light opening in the upper rear section of the vehicle.
- Connect the 4PIN mini connector of the camera sensor to the mini connector counterpart of the main wire, securing the connectors with isolating tape.
- Connect the system plug with the connector counterpart of the brake light reflector housing.
- Re-mount the brake light reflector housing on top of the main camera housing using the original Philips cross-recess screws.
- Perform a function test after connecting the main cable to the control unit in the dashboard (no picture provided).
- If necessary, align the camera ball at the bottom side of the camera main body using the supplied U-shaped tool.
CONNECTION DIAGRAM
| COMPATIBLE WITH | MODEL TYPE | MODEL YEAR |
|---|---|---|
| Fiat Ducato III | 250/251 | 2006 – 2011 |
| Fiat Ducato III | 250/251 | 2011 – 2014 |
| Fiat Ducato III | 250/251 (X290) | 2014 – 2021 |
| Fiat Ducato III | Series 8 | 2021 – 2023 |
| Fiat Ducato III | Series 9 | as of 2023 |
| Citroën Jumper II | 250/250D/250L | as of 2006 |
| Peugeot Boxer | 250/251 | as of 2006 |
| Opel Movano | Type C | as of 2021 |
KEY FEATURES
- Compact high-resolution rear view camera for FIAT Ducato III vehicles and type variants
- System design integrating the original Ducato brake light retaining the road use homologation
- High quality SONY CMOS picture sensor with low power consumption
- Detailed high contrast picture under twilight conditions
- 11 m main wire length
- Mechanically adjustable cam angle, allowing field of view personalization
- Plastic injection main housing with stainless steel fixation bolts
DESCRIPTION
- This ZENEC rear view camera model has been developed for use with FIAT Ducato III based vehicle and motor homes in particular. This camera product deploys high quality parts and materials though out, to provide reliable operation and appropriate longevity in the target vehicles mentioned.
- The ZE-RCE3701-MK2-S offers a large 160° diagonal viewing angle. The camera complies with a great variety of infotainer models made for CVBS rear view cam signal input.
TECHNICAL SPECIFICATIONS
- Image device: 6.09 mm SONY IMX225LQR CMOS sensor
- Lens focal length: f 1.2
- TV system: NTSC / 30 fps
- View angle: 160° (D) x 130° (H) x 120° (V)
- Native sensor resolution: 1305 (H) x 977 (V) pixels
- Resolution of video-out: > 420 TV lines
- Frame rate: 30 fields/sec.
- Signal to noise ratio: > 48 dB
- Light sensitivity: 0.3 Lux
- Video output: 1.0 Vp-p, 75 ohms CVBS
- White balance: Auto
- Backlight compensation: Auto
- Gamma correction: 0.45
- Gain control: Auto
- Sync system: Auto
- Power supply: DC 6 – 24V
- Current consumption: 70 mA @12VDC, ≤ 840 mW
- IP protection rating: IP69K
- Operating temperature: -30°C~+75°C, RH 95% max
CAUTION:
Use the included connection cable exclusively. Altering or replacing it will
void your warranty. The camera is water- and dustproof and has been licensed
according to the international standard IP69K. However, vehicle cleaning using
high pressure water and steam jet devices may still lead to damage of IP69K
rated camera models by water intrusion. Keep a distance of at least one meter
between the water nozzle and the camera housing
INSTALLATION
- Loosen the two Phillips cross recess screws
- Remove the brake light reflector housing. Un-connect the white system plug of the vehicle.
- Screw in and tighten the stainless steel mounting bolts by hand (5Nm). Use a dab of Loctite, if possible
- Route the main cable from the infotainer in the vehicle cockpit / dashboard to the brake light opening in the upper rear section of the vehicle. Fore power and RCA video signal, the ZENEC infotainer offers a direct system “connector block E” which offers switched 300mA power out’s (see installation guide of ZENEC head unit).
- Connect the 4PIN mini connector of the camera sensor to the mini connector counterpart of the main wire. Wrap around some isolating tape to secure the connectors
- Connect the system plug with the connector counterpart of the brake light reflector housing
- Re-mount the brake light reflector housing on top of the main camera housing, using the original Philips crossrecess screws.
- no picture After connecting the main cable to the control unit in the dashboard > perform function test
- Alignment of the camera ball at the bottom side of the camera main body if necessary, using the supplied U-shaped tool.
UK Declaration of Conformity
Hereby, ACR Brändli + Vögeli AG declares that ZENEC ZE-RCE3701-MK2-S-S is UKCA
compliant – the UK Declaration of Conformity can be accessed via the following
Internet address: http://www.zenec.com (see link „Product Conformity
Documents“ in the footer area of the page).
UK Authorised Representative (for authorities only) ProductIP (UK) Ltd. 8,
Northumberland Av. London WC2N 5BY
ZENEC by ACR AG
Bohrturmweg 1
CH-5330 Bad Zurzach
Switzerland, EU Legal Representative: ACR S & V GmbH
Industriestr. 35 ∙ D-79787 Lauchringen
Germany
www.zenec.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>