Bright 022933 Shoe Drier Instruction Manual

Bright 022933 Shoe Drier

Product Information

The Shoe Drier is a product manufactured by Jula AB. It is designed to dry shoes and boots effectively. The product operates on a voltage of 230 V, with a frequency of 50 Hz. It has a power output of 250 W and produces a noise level of 49 dB. The shoe drier comes with a cord length of 130 cm and a hose length of 65 cm. It is classified as Safety class II and is approved in accordance with relevant directives. The product should be installed by wall mounting, using the provided wall bracket.

Product Usage Instructions

1. Plug in the shoe drier into a power outlet.
2. Insert the hoses of the shoe drier into the shoes or boots thatneed to be dried.
3. Set the timer to the desired drying time. The shoe drier willstart operating and the status light will turn on.
4. Once the timer reaches 0, the shoe drier will switch offautomatically. If the shoes or boots are not completely dry, startthe timer again to continue drying.

Note: The shoe drier has built-in overheat protection. In case of overheating, the safety switch will turn off the shoe drier. To reset the safety switch, follow these steps:

1. Turn off the shoe drier and unplug it from the poweroutlet.
2. Wait for a few minutes to allow the shoe drier to cooldown.
3. After the shoe drier has cooled down, you can plug it back inand use it again.

Jula AB reserves the right to make changes to the product. Jula AB claims copyright on this documentation. It is not allowed to modify or alter this documentation in any way and the manual shall be printed and used as it is in relation to the product. For the latest version of operating instructions, refer to the Jula website.

SAFETY  INSTRUCTIONS

• Read the instructions carefully before use and save them for future
• This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved with its Do not allow children to play with the product. Do not allow children to clean or maintain the product without supervision.
• Only connect the product to 230 V
• Do not cover the product with washing or other
• Do not block the hot air
• Do not let the power cord come into contact with the product when it is
• Warning: Do not use the product in the bathroom, kitchen or other places where there is
• Never immerse the product in water or any other Pull out the plug immediately if the product comes into contact with water.
• Switch off the product and pull out the plug after use and before
• Children often do not understand that it can be dangerous to use electrical Never allow children to use the product on their own.
• Never touch the product when it is in use – it gets very
• Do not use the product if it, or the power cord are damaged. Take it to an authorised service centre to have it repaired.
• The product is only intended for indoor
• Do not put foreign objects in any of the ventilation
• This can result in electric shock, fire, or damage the product.
• To prevent overloading, check that no other electrical appliances are connected to the same circuit as the product.

SYMBOLS

TECHNICAL DAT

INSTALLATION

Wall mounting Screw the wall bracket to the wall so that the hoses reach down to the floor.

NOTE

Fit the wall bracket so that the arrow points up. Hook the shoe drier onto the wall bracket.

USE

HOW TO USE

1. Plug in the shoe
2. Put the hoses in the shoes or boots to be dried.
3. Turn the timer to the time required
   • the drier starts and the status light goes on.
4. The status light goes on when the shoe drier is
5. The shoe drier switches off automatically when the timer reaches “0”. Start the timer again to continue drying the shoes.

Overheating protection

A safety switch switches off the shoe drier if it overheats. Do as follows if the overheating protection has been activated:

1. Switch off the shoe drier and pull out the
2. Attend to the reason for overheating, such as a covered air inlet, dust or
3. Allow the shoe drier to cool for a few
4. Plug in and start the shoe drier again

MAINTENANCE

CLEANING

• Check the shoe drier at regular
• First pull out the Check if dust or fluff has accumulated inside the ventilation grille.
• If necessary, wipe the outside of the shoe drier with a damp cloth and use a vacuum cleaner to clean the air

References

• Jula – products for home and garden

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>