ZENEC ZE-RVSC150MV Multiview Rear View Camera for Motorhomes Instruction Manual
- June 13, 2024
- ZENEC
Table of Contents
ZENEC ZE-RVSC150MV Multiview Rear View Camera for Motorhomes
Product Information
- The ZE-RVSC150MV is a multiview rear view camera specifically designed for motorhomes. It is equipped with a 12 V > 5.5 V step-down converter and TTL controller board for power supply and control. The camera has a male bullet connector for +12V and GND, a video (CVBS) RCA connector, and a MV data line with a 6.3 x 0.8 mm male spade connector. It also features an original connection with a female 4PIN mini connector and a micro 4PIN male connector.
- The camera is water- and dustproof, certified with an IP68protection rating. However, it is important to note that high-pressure water and steam jet devices used for vehicle cleaning may still damage the camera if the water intrudes. To prevent damage, maintain a distance of at least one meter between the water nozzle and the camera sensor/housing during high-pressure cleaning.
- The camera’s technical specifications include a 1/3″ 8.51 mm Pixelplus PC1058C CMOS image sensor, NTSC TV system, 30 fps frame rate, 43.3 dB signal-to-noise ratio, 1.0 Lux light sensitivity (0 Lux with IR-ON), and a video output of 1.0 Vp-p (+/- 0.2 V) 75 Ohm CVBS. It also has automatic features for electronic shutter, white balance, gain control, and backlight compensation. The camera operates on a 12VDC power supply and has low power consumption.
- The camera should be mounted in the center rear of the motorhome, with the sensor pointing downwards. The optimal height for the camera sensor above the ground is approximately 220 to 265 cm.
Product Usage Instructions
- Determine the desired mounting location for the camera.
- Remove the rubber foot from the camera body and use it as a template to mark the mounting holes and cable entry on the mounting surface.
- Ensure there is enough accessible space on the back of the mounting surface for inserting, pulling, and routing the camera cable.
- Drill three mounting holes with a 3.5 mm metal drill and one hole for the cable entry with a 7.5 mm metal drill.
- Vacuum out any metal shavings and seal the drill holes with lacquer or paint.
- Connect the camera’s video RCA plug, multi-view data line, and power supply cable to the corresponding connections of the head unit.
- Perform a camera test run to ensure proper functionality.
Note : It is essential to use the included connection cable exclusively, as modifying the cable will void the warranty.
OVERVIEW
KEY FEATURES
- Compact universal “multi-view” rear view camera for use with selected, multi-view control compatible ZENEC device models
- Multi-view function offering six camera image display modes, selectable via touchscreen of ZENEC device (normal, top-down, panorama, L/R blind-spot, 2- split-screen, triple split-screen)
- High quality CMOS picture sensor with low power consumption, for detailed high contrast cam image
- IR LED lighting with 5 LEDs and dynamic brightness control via LDR element
- Robust white painted die-cast aluminum housing with mechanical adjustment of vertical image section
- 15 m long separable system cable equipped with mini 4-PIN connectors
- IP68 certified
CAUTION
- Use the included connection cable exclusively. Modifying the cable will void your warranty.
- The camera is water- and dustproof and has been licensed according to the international standard IP68. However, vehicle cleaning using high pressure water and steam jet devices may still lead to damage of IP68 rated camera models by intrusion of water.
- If the motorhome is treated with a water jet high pressure cleaning device, make sure to keep a distance of at least one meter between the water nozzle and the camera sensor / housing.
TECHNICAL SPECIFICATIONS
- Image device: 1/3” / 8.51 mm Pixelplus PC1058C CMOS Sensor
- Horizontal view angle: 180° (max.) – image areas controllable via ZENEC device
- TV system: NTSC / 30 fps
- Effective sensor resolution: 960(H) x 576(V) pixels
- Resolution of video-out signal: 700 TV lines
- Frame rate: 30 fi elds/sec.
- Signal to noise ratio: 43.3 dB
- Light sensitivity: 1.0 Lux, 0 Lux with IR-ON
- Video output: 1.0 Vp-p (+/-0.2 V), 75 ohms, CVBS
- Electronic shutter: auto
- White balance: auto
- Automatic gain control: auto
- Backlight compensation: auto
- Power supply: 5.5 – 12 VDC
- Current consumption: 1,200 mW (220±5 mA@5.5 V
- via step-down converter)
- IP protection rating: IP68
- Operating temperature: -20°C~+70° C
- Dimensions L x W x H: 74 x 54 x 44 mm
INSTALLATION
- The ZE-RVSC150MV is mounted in the center rear of the vehicle with the sensor pointing downwards. The camera sensor cannot be adjusted mechanically. For an optimal image viewing fi eld, the camera sensor should be about 220 to 265 cm above the ground.
- Determine the approximate desired mounting location for the camera.
- If you look at the foot area of the camera, you will see three through mounting holes for the mounting screws in the rubber base and the metal base – with a diameter of about 5mm, as well as a larger center feed-through hole for the camera cable.
- Pull the rubber foot off the camera body and use it as a template to mark the mounting holes and cable entry. Ensure that there is adequate accessible space on the back of the mounting surface for inserting/pull-ing/routing the camera cable. Mark the holes with an Edding pen. The mounting holes for the three self-tapping metal screws must be drilled with a 3.5 mm metal drill, the hole for the cable entry with a 7.5 mm metal drill. Vacuum out the metal shavings and seal the drill holes with some lacquer or paint.
- Disassemble the camera using the Allen key included in the kit to remove the rear case. Press the rubber foot back onto the camera base. Feed the camera cable into the drilled hole in the middle and carefully screw down the camera with the three self-tapping metal screws included in the set. Align the camera vertically – tighten the screws snugly and reattach the back of the camera to the camera main body with sensor using the four Allen screws. Now lay the 15 m long extension cable from the mounting location of the camera to the device mounting slot in the dashboard.
- Connect the camera’s video RCA plug, the multi-view data line and the power supply cable to the designated connections of the head unit. Do a camera test run.
UK Declaration of Conformity
Hereby, ACR Brändli + Vögeli AG declares that ZENEC ZE-RVSC150MV is CE
compliant – the EU Declaration of Conformity can be accessed via the following
Internet address: http://www.zenec.com (see link „Product Conformity
Documents“ in the footer area of the page).
UK Authorised Representative (for authorities only) ProductIP (UK) Ltd. 8,
Northumberland Av. London WC2N 5BY
ZENEC by ACR AG ∙ Bohrturmweg 1 ∙ CH-5330 Bad Zurzach ∙ Switzerland, EU Legal
Representative: ACR S & V GmbH ∙ Industriestr. 35 ∙ D-79787 Lauchringen ∙
Germany ∙ www.zenec.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>