inELS RFSAI-62B-SL Switch Unit Instruction Manual
- June 4, 2024
- inELS
Table of Contents
inELS RFSAI-62B-SL Switch Unit
Characteristics
- The switching component with one/two output relays is used to control appliances and lights. Switches/buttons connected to the wiring can be used for control.
- They can be combined with Detectors, Controllers or iNELS RF Control System Components.
- The BOX version offers installation directly in the installation box, ceiling or cover of the controlled appliance. Easy installation thanks to screwless terminals.
- It allows the connection of switched loads with a total sum of 8 A (2,000 W).
- Functions: for RFSAI 61B-SL and RFSAI 62B-SL – pushbutton, impulse relay and time functions of delayed start or return with time setting 2 s-60 min. Any function can be assigned to each output relay. For RFSAI-11B-SL, the button has a fixed function – ON / OFF.
- The external button is assigned in the same way as the wireless one.
- Each of the outputs can be controlled by up to 12/12 channels (1-channel represents one button on the controller). Up to 25 channels for RFSAI-61B-SL and RFSAI-11B-SL.
- The programming button on the component also serves as a manual output control.
- Possibility to set the output status memory in case of failure and subsequent power recovery.
- The elements of the repeater can be set for the components via the RFAF / USB service device, PC, application.
- Range up to 200 m (outdoors), in case of insufficient signal between the controller and the device, use the RFRP-20 signal repeater or component with the RFIO2 protocol that support this function.
- Communication with bidirectional RFIO2 protocol.
- The contact material of the AgSnO2 relay enables switching of light ballasts.
Assembly
mounting in an installation box (even under the existing button / switch)
mounting into
the light cover
ceiling
mounted
Connection
RFSAI-61B-SL
RFSAI-62B-SL
Screw less terminals 
**Radio frequency signal penetration through various construction
materials**
| 
| |
| **
---|---|---|---|---
60 – 90 %| 80 – 95 %| 20 – 60 %| 0 – 10 %| 80- 90 %
brick walls| wooden structures with plaster boards| reinforced concrete| metal
partitions| ** common glass
Indication, manual control
- LED / PROG button
- LED green V1 – device status indication for output 1
- LED red V2 – device status indication for output 2. Indicators of memory function:
- On – LED blinks x 3.
- Off – The LED lights up once for a long time.
- Manual control is performed by pressing the PROG button for<1s.
- Programming is performed by pressing the PROG button for 3-5s.
- Terminal block – connection for external button
- Terminal block – connecting the neutral conductor
- Terminal block – load connection with the sum of the total current 8A (eg V1=6A, V2=2A)
- Terminal block for connecting the phase conductor
In the programming and operating mode, the LED on the component lights up at the same time each time the button is pressed – this indicates the incoming command.
-
RFSAI-61B-SL: one output contact, status indication by red LED
-
Use a suitable tool (paper clip, screwdriver) to push on the control pin. The batteries are raised and the programming button is released.
-
After removing the control flaps, the programming button is accessible.
-
The programming button is operated with a suitable thin tool.
Compatibility 
The device
can be combined with all system components, controls and devices of iNELS RF
Control and iNELS RF Control2. The detector can be assigned an iNELS RF
Control2 (RFIO2) communication protocol.
Channel selection
Channel selection (RFSAI-62B-SL) is done by pressing the PROG buttons for
1-3s. RFSAI-61B-SL: press for more than 1 second. After button release, LED is
flashing indicating the output channel: red (1) or green (2). All other signals
are indicated by corresponding color of LED for each channel.
Functions and programming with RF transmitters
Function button
Description of button The output contact will be closed by pressing the
button and opened by releasing the button. For the correct execution of
individual commands (press = closing / releasing the button = opening), the
time delay between these commands must be a min of . 1s (press – delay 1s –
release).
Programming
Press of
programming button on receiver RFSAI-62B for 3-5 s (RFSAI-61B-SL: press for
more than 1 s) will activate receiver RFSAI-62B into programming mode. LED is
flashing in 1s interval.
Select and
press one button on wireless switch, to this but-ton will be assigned function
Button.
Press of
programming button on receiver RFSAI-62B shorter then 1 second will finish
programming mode. The LED lights up according to the pre-set memory function.
Function switch on
Description of switch on
The output
contact will be closed by pressing the button.
Programming
Press of programming button on receiver RFSAI-62B for 3-5 s (RF-SAI-11B-SL:
press for more than 1s) will activate receiver RFSAI-62B into programming
mode. LED is fl ashing in 1s interval.
Two presses of
your selected button on the RF transmitter assigns the function switch on
(must be a lapse of 1s between individual presses).
Press of programming button on receiver RFSAI-62B shorter then 1 second will
finish programming mode. The LED lights up according to the pre-set memory
function.
Function switch off
Description of switch off
The output contact will be opened by pressing the button.
Programming
Press of
programming button on receiver RFSAI-62B for 3-5 s (RF-SAI-61B-SL: press for
more than 1 s) will activate receiver RFSAI-62B into programming mode. LED is
fl ashing in 1s interval.
Three presses of
your selected button on the RF transmitter assigns the function switch off
(must be a lapse of 1s between individual presses).
Press of
programming button on receiver RFSAI-62B shorter then 1 second will finish
programming mode. The LED lights up according to the pre-set memory function.
Function impulse relay
Description of impulse relay
The output contact will be switched to the opposite position by each press of
the button. If the contact was closed, it will be opened and vice versa.
Programming
Press of
programming button on receiver RFSAI-62B for 3-5 s (RFSAI-61B-SL: press for
more than 1 s) will activate receiver RFSAI-62B into programming mode. LED is
fl ashing in 1s interval.
Four presses of
your selected button on the RF transmitter as-signs the function impulse relay
(must be a lapse of 1s between individual presses).
Press of
programming button on receiver RFSAI-62B shorter then 1 second will finish
programming mode. The LED lights up according to the pre-set memory function.
Function delayed off
Description of delayed off
The output contact will be closed by pressing the button and opened after the
set time interval has elapsed.
Programming
Press of programming button on receiver RFSAI-62B for 3-5 s (RF-SAI-61B-SL:
press for more than 1 s) will activate receiver RFSAI-62B into programming
mode. LED is fl ashing in 1s interval.
Assignment of the delayed off function is performed by fi ve presses of the
selected button on the RF transmitter (must be a lapse of 1s between
individual presses).
Press of programming button longer then 5 seconds, will activate actuator into
timing mode. LED flashs 2x in each 1s interval. Upon releasing the button, the
delayed return time starts counting.
After the desired time has elapsed (range of 2s…60min), the timing mode ends
by pressing the button on the RF transmitter, to which the delayed return
function is assigned. This stores the set time interval into the actuator
memory.
Press of programming button on receiver RFSAI-62B shorter then 1 second will fi
nish pro-gramming mode. The LED lights up according to the pre-set memory
function.
Function delayed on /
Description of delayed on /
The output contact will be opened by pressing the button and closed after the
set time interval has elapsed.
Programming /
Press of programming button on receiver RFSAI-62B for 3-5 s (RF-SAI-61B-SL:
press for more than 1s) will activate receiver RFSAI-62B into programming
mode. LED is fl ashing in 1s interval.
Assignment of
the delayed on function is performed by six presses of the selected button on
the RF transmitter (must be a lapse of 1s between individual presses).
Press of programming button longer then 5 seconds, will activate actuator into
timing mode. LED flashs 2x in each 1s interval. Upon releasing the button, the
delayed return time starts counting.
After the desired time has elapsed (range of 2s…60min), the timing mode ends
by pressing the button on the RF transmitter, to which the delayed return
function is assigned. This stores the set time interval into the actuator
memory.
Press of programming button on receiver RFSAI-62B shorter then 1 second will
finish programming mode. The LED lights up according to the pre-set memory
function.
Programming with RF control units
Addresses
listed on the front side of the actuator are used for programming and
controlling the actuator and individual RF channels by control units.
Deleting one position of the transmitter
By pressing the programming button on the actuator for 8 seconds (RFSAI-61B-
SL: press for 5 second), deletion of one transmitter activates. LED flashs 4x
in each 1s interval. Pressing the required button on the transmitter deletes
it from the actuator’s memory. To confirm deletion, the LED will confirm with a
fl ash long and the component returns to the operating mode. The memory status
is not indicated. Deletion does not affect the pre-set memory function.
Deleting the entire memory
By pressing the
programming button on the actuator for 11 seconds (RFSAI-61B-SL: press for
more than 8 second), deletion occurs of the actuator’s entire memory. LED
flashs 4x in each 1s interval. The actuator goes into the programming mode, the
LED fl ashes in 0.5s intervals (max. 4 min.). You can return to the operating
mode by pressing the Prog button for less than 1s. The LED lights up according
to the pre-set memory function and the component returns to the operating
mode. Deletion does not affect the pre-set memory function.
Selecting the memory function
Press of programming button on receiver RFSAI-62B for 3-5 second (RFSAI-61B-
SL: press for 1 second) will activate receiver RFSAI-62B into programming
mode. LED is flashing in 1s interval.
Pressing the programming button on the RFSAI-62B receiver for less than 1
second will finish the programming mode, this will re-verse the memory
function. The LED lights up according to the current pre-set memory function.
The set memory function is saved. Every other change is made in the same way.
- Memory function on:
- For functions 1-4, these are used to store the last state of the relay output before the supply voltage drops, the change of state of the output to the memory is recorded 15 seconds after the change.
- For functions 5-6, the target state of the relay is immediately entered into the memory after the delay, after re-connecting the power, the relay is set to the target state.
- Memory function off:
When the power supply is reconnected, the relay remains off.
The external button RFSAI-62B-SL is programmed in the same way as for
wireless. RFSAI-11B-SL it is not programmed, it has a fixed function.
Technical parameters
RFSAI-11B-SL
RFSAI-61B-SL
RFSAI-62B-SL
| Supply voltage: | Napájecí napětí: | 230 V AC |
|---|---|---|
| Supply voltage frequency: | Frekvence napájecího napětí: | 50-60 Hz |
| Apparent input: | Příkon zdánlivý: | 7 VA / cos φ = 0.1 |
| Dissipated power: | Příkon ztrátový: | 0.7 W |
| Supply voltage tolerance: | Tolerance napájecího napětí: | +10 %; -15 % |
| Output | Výstup | |
| Number of contacts: | Počet kontaktů: | 1x switching / 1x spínací |
2xspínací
Rated current:| Jmenovitý proud:| 8 A / AC1
Switching power:| Spínaný výkon:| 2000 VA / AC1
Peak current:| Špičkový proud:| 10 A / <3 s
Switching voltage:| Spínané napětí:| 250 V AC1
Mechanical service life:| Mechanická životnost:| 1×107
Electrical service life (AC1):| Elektrická životnost (AC1):| 1×105
Control| Ovládán í|
Wireless:| Bezdrátově:| 25-channels/ 25 kanálů 2
x 12-channels/ 2 x 12 kanály
Number of functions:| Počet funkcí:| 1| 6| 6
Communication protocol:| Komunikační protokol:| RFIO2
Frequency:| Frekvence:| 866–922 MHz (for more information see p. 74)/ 866–922
MHz (viz str. 74)
Repeater function:| Funkce repeater:| yes/ ano
Manual control:| Manuální ovládání:| button PROG (ON/OFF)/ tlačítko PROG
(ON/OFF)
External button / switch: Range:| Externím tlačítkem:| yes/ ano
Other data| Dosah:| in open space up to 200 m/ na volném prostranství až 200 m
Operating temperature:| Další údaje|
Operating position:| Pracovní teplota:| -15 až + 50 °C
Operating position:| Pracovní poloha:| any/ libovolná
Mounting:| Upevnění:| free at lead-in wires/ volné na přívodních vodičích
Protection:| Krytí:| IP40
Overvoltage category:| Kategorie přepětí:| III.
Contamination degree:| Stupeň znečištění:| 2
Connection:| Připojení:| screwless terminals/ bezšroubové svorky
Connecting conductor:| Průřez připojovacích vodičů (mm2)| 0.2-1.5 mm2
solid/flexible/ 0.2-1.5 mm2 pevný/pružný
Dimensions:| Rozměr:| 43 x 44 x 22 mm
Weight:| Hmotnost:| 31g| 45 g
Related standards:| Související normy:| EN 60730, EN 63044, EN 300 220, EN 301
489
- Control button input is at the supply voltage potential.
Attention:
When you instal iNELS RF Control system, you have to keep minimal distance 1
cm between each units. Between the individual commands must be an interval of
at least 1s.
Warning
Instruction manual is designated for mounting and also for user of the device.
It is always a part of its packing. Installation and connection can be carried
out only by a person with adequate professional qualification upon under-
standing this instruction manual and functions of the device, and while
observing all valid regulations. Trouble-free function of the device also
depends on transportation, storing and handling. In case you notice any sign
of damage, deformation, malfunction or missing part, do not install this
device and return it to its seller. It is necessary to treat this product and
its parts as electronic waste after its lifetime is terminated. Before
starting installation, make sure that all wires, connected parts or terminals
are de-energized. While mounting and servicing observe safety regulations,
norms, directives and professional, and export regulations for working with
electrical devices. Do not touch parts of the device that are energized – life
threat. Due to transmissivity of RF signal, observe correct location of RF
components in a building where the installation is taking place. RF Control is
designated only for mounting in interiors. Devices are not designated for
installation into exteriors and humid spaces. The must not be installed into
metal switchboards and into plastic switchboards with metal door –
transmissivity of RF signal is then impossible. RF Control is not recommended
for pulleys etc. – radiofrequency signal can be shielded by an obstruction,
interfered, battery of the transceiver can get fl at etc. and thus disable
remote control.
ELKO EP declares that the RFSG type of equipment complies with Directives
2014/53/EU, 2011/65/EU, 2015/863/EU and 2014/35/EU. The full EU Declaration of
Conformity is at: https://www.elkoep.com/wireless-contact-converter-230v
—rfsg-1m
ELKO EP, s.r.o., Palackého 493, 769 01 Holešov, Všetuly, Czech Republic
Tel.: +420 573 514 211,
e-mail: elko@elkoep.com,
www.elkoep.com
References
- ELKO EP - Výrobce elektronických přístrojů • ELKO EP s.r.o
- ELKO EP - Výrobce elektronických přístrojů • ELKO EP s.r.o
- Převodník kontaktu RFSG-1M • ELKO EP s.r.o
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>