beamZ S1500 LED Smoke Machine with Timer Control Instruction Manual

: June 4, 2024
: beamZ

Table of Contents

beamZ S1500 LED Smoke Machine with Timer Control
Safety Information
UNPACKING INSTRUCTION
POWER SUPPLY
INSTALLATION
SETTINGS
CLEANING
DMX CHANNELS
TECHNICAL SPECIFICATION
Declaration of Conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

beamZ S1500 LED Smoke Machine with Timer Control

beamZ-S1500-LED-Smoke-Machine-with-Timer-Control-
product

Congratulations to the purchase of this Beamz product. Please read this manual thoroughly prior to using the product in order to benefit fully from all features. Read the manual prior to using the product. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock. Keep the manual for future reference.

Safety Information

Prior to using the product, please ask for advice from a specialist. When the unit is switched on for the first time, some smell may occur. This is normal and will disappear after a while.
The unit contains voltage-carrying parts. Therefore, do NOT open the housing.
Do not place metal objects or pour liquids into the product. This may cause electrical shock and malfunction.
Do not place the product near heat sources such as radiators, etc. Do not place the unit on a vibrating surface. Do not cover the ventilation holes.
The product is not suitable for continuous use.
Be careful with the mains lead and do not damage it. A faulty or damaged mains lead can cause electrical shock and malfunction.
When unplugging the product from a mains outlet, always pull the plug, never the lead.
Do not plug or unplug the unit with wet hands.
If the plug and/or the mains lead are damaged, they need to be replaced by a qualified technician.
If the product is damaged to such an extent that internal parts are visible, do NOT plug the unit into a mains outlet, and DO NOT switch the product on. Contact your dealer. Do NOT connect the product to a rheostat or dimmer.
To avoid fire and shock hazards, do not expose the product to rain and moisture.
All repairs should be carried out by a qualified technician only.
Connect the product to an earthed mains outlet (220-240Vac/50Hz) protected by a 10-16A fuse.
During a thunderstorm or if the product will not be used for a longer period of time, unplug it from the mains. The rule is: Unplug it from the mains when not in use.
If the product has not been used for a longer period of time, condensation may occur. Let the unit reach room temperature before you switch it on. Never use the product in humid rooms or outdoors.
During operation, the housing becomes very hot. Do not touch it during the operation and immediately after.
To prevent accidents in companies, you must follow the application guidelines and follow instructions.
Secure the product with an extra safety chain if the unit is ceiling mount. Use a truss system with clamps. Make sure nobody stands in the mounting area. Mount the effect at least 50cm away from inflammable material and leave at least 1-meter space on every side to ensure sufficient cooling.
This product contains high-intensity LEDs. Do not look into the LED light to prevent damage to your eyes.
Do not repeatedly switch the product on and off. This shortens the lifetime.
Keep the unit out of the reach of children. Do not leave the unit unattended.
Do not use cleaning sprays to clean switches. The residues of these sprays cause deposits of dust and grease. In case of malfunction, always seek advice from a specialist.
Only operate the product with clean hands.
Do not force the controls.
If the product has fallen, always have it checked by a qualified technician before you switch the product on again.
Do not use chemicals to clean the unit. They damage the varnish. Only clean the product with a dry cloth.
Keep away from electronic equipment that may cause interference.
Only use original spares for repairs, otherwise serious damage and/or dangerous radiation may occur.
Switch the product off prior to unplugging it from the mains and/or other equipment. Unplug all leads and cables prior to moving the product.
Make sure that the main lead cannot be damaged when people walk on it. Check the mains lead before every use for damages and faults!
The mains voltage is 220-240Vac/50Hz. Check if the power outlet match. If you travel, make sure that the main voltage of the country is suitable for this product.
Keep the original packing material so that you can transport the product in safe conditions

This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient magnitude to cause a shock hazard. This mark attracts the attention of the user to important instructions that are contained in the manual and that he should read and adhere to. DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks should be aware of the effects that this light effect may have on them.

The product has been certified CE. It is prohibited to make any changes to the product. They would invalidate the CE certificate and their guarantee!

NOTE:
To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and 35°C/95°F.

Electric products must not be put into household waste. Please bring them to a recycling center. Ask your local authorities or your dealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice. prior notice. Do not attempt to make any repairs yourself. This would invalidate your warranty. Do not make any changes to the product. This would also invalidate your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use or disrespect of the warnings contained in this manual. Beamz cannot be held responsible for personal injuries caused by the disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.

UNPACKING INSTRUCTION

CAUTION!
Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain the packing material for inspection if any parts appear damaged from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original factory box and packed.

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

POWER SUPPLY

On the label on the backside of the product is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and may be used. No dimmer or adjustable power supply. Always connect the device to a protected circuit (circuit breaker or fuse). Make sure the device has an appropriate electrical ground to avoid the risk of electrocution or fire.

INSTALLATION

CAUTION:
Please consider the respective national norms during the installation! The installation must only be carried out by an authorized employee or dealer!

Attention:

When the smoke machine has a built-in fluid tank, then should be transported and operated in an upright position.
Use only Beamz water-based fluid recommended by your dealer. Poor liquid caused permanent damage, bad effect, clogging, spitting of unevaporated liquid, etc.
Be sure that the smoke machine is positioned on a stable, non-slip surface.
Be sure that no ventilation slots on the product’s housing are blocked.
Don’t put any objects on the smoke machine.
Always install the smoke machine in an area with adequate ventilation.
Never connect the smoke machine to a dimmer or rheostat.
In the event of a serious operating problem, stop using the product immediately.
When mounted at height, use the bracket and use add a safety cable.
The installation of the smoke machine has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harmful deformation.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled person once a year.
Never aim the smoke at yourself, people or animals.
Never aim the output nozzle directly at people or at open flames.
The smoke machine has to be installed out of the reach of people and animals.
Drain the tank before transporting or storing the product.
Never drink smoke fluid or use it on the inside or outside of a human body. If fluid gets in contact with skin or eyes, rinse thoroughly with water and call a doctor immediately!
Keep out of the reach of children.
For indoor use only.

CAUTION:
When installing the smoke machine, make sure there is no highly in inflammable material (decoration articles, etc.) in between a distance of min. 20inch or 0.5 meters.

SETTINGS

Via the Menu key, you can adjust the desired settings. After pressing the menu, the display shows the following settings:

Man Vol Out xxx%.
Adjust the manual volume output within the range of 0% to 100% by means of the Up/Down keys.
Interval Set xxxS
Adjust the interval between each fog emission within the range of 1 to 100S by means of the Up-/Down keys.
Duration Set xxxS
Adjust the duration of each fog emission within the range of 1 to 100S.
Volume Out xxx%
Adjust the volume output during the timer function within the range of 0-100%
DMX 512 #xxx
Adjust the DMX address for DMX control.
Wind For Class xx
NO FUNCTION for this smoke machine
Angel Set xx%
NO FUNCTION for this smoke machine
LED Pro Set xx
Adjust the LED program within the range of 0 to 11.
LED Spe xxx
Adjust the LED speed/strobe/fade of the LED program mode
Temper Max:xxx
Adjust the maximum heating temperature of the heating element, adjustable between 285° – 330°C.
LED Sync Set Yes/No
Adjust the LED mode. Yes=LEDs work together with the smoke output, NO=LEDs are always on.
Temper Min:xxx
Adjust the minimum heating temperature of the heating element, adjustable between 260° – 310°C.

TIMER CONTROL
Press the Timer key to activate the timer function. The display shows the adjusted interval and the device counts the seconds down to “0”. After that, the fog emission is triggered at the volume adjusted under “Timer Out”. The duration depends on the settings adjusted under “Duration Set”. If you wish to deactivate the timer function, press the Timer key once more.

MANUAL CONTROL (LOCKED)
Press the Lock switch (5) for immediate triggering of the fog emission at the volume adjusted under “Volume Out”. Press the Volume switch once more in order to stop the fog emission.

MANUAL CONTROL (100% OUTPUT)
Press the Manual key for immediate triggering of the fog emission at 100 % volume. Let the Manual key loose in order to stop the fog emission.

DMX CONTROL
Connect the machine directly to a DMX controller or a DMX loop with multiple DMX effects. The machine uses a 3-pin XLR connector for DMX connection.

Address Setup:
Press the MODE button a number of times until Add appears on the display, with the UP / DOWN buttons the start address may be set. The start address is defined as the first channel to which the machine will respond to. Check that there are no overlapping channels used!

Note: It is necessary always lock the DMX loop with a 120 Ohm terminator for correct data transmission. The DMX data will only be saved when the display shows “Ready to Fog”.

CLEANING

After 40 operating hours, the smoke machine must be cleaned to avoid deposits in the machine, pump, and heater.

Run clean procedure in a well-ventilated area!

Procedure:

Remove smoke fluid from the tank, and fill “Beamz smoke machine cleaner fluid” (item no. 160.670) into the empty tank.
Switch the power on and wait until the smoke machine is warmed up.
Press the button of the remote control and pump the liquid through the machine.
Perform the above operation until the tank is empty.
Fill the tank with Beamz smoke fluid.

DMX CHANNELS

Channel	Function	Value	Description
1	Fog	000-255	Control the output volume
2

Colour

| 000-255| Master dimmer 0-100%
3| 000-255| LED Red 0-100%
4| 000-255| LED Green 0-100%
5| 000-255| LED Blue 0-100%
6| Strobe| 000-255| Strobe from slow to fast
7| Auto mode| 000-255| Automatic LED program

TECHNICAL SPECIFICATION

Rated voltage: AC220～240V 50/60Hz
Heating element: 1500W
LED: 9x 3W RGB
Heat up time: 3.5 minutes
Tank capacity: ca 2.5 liters
DMX Channels: 7 Channels
Function: DMX/Stand-alone
Dimensions per unit: 465 x 255 x 196mm
Weight (per unit): 5.85kg

The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.

Declaration of Conformity

Manufacturer:
- Tronios B.V. Bedrijvenpark Twente 415 7602KM Almelo The Netherlands
- Phone: +31(0)85-1053155
Product number: 160.455
Product Description: S1500LED Smoke machine
Trade Name: BEAMZ
Regulatory Requirement:
- EN 55014-1: 2006+ A1:2009+A2:2011
- EN 61000-3-2: 2006+ A1:2009+A2:2009
- EN 61000-3-3: 2008
- EN 55014-2: 1997+ A1:2001+A2:2008
- EN 60204-1: 2004+ A1:2009

I hereby declare that the product meets the requirements stated in Directives 2014/35/EU, 2014/30/EU 2011/65/EU and conforms to the above mentioned Declarations.

Almelo, 14-05-2018
Name : M. Velders