beamZ 153.683 V2.0 LEDWAVE LED Jellyball Water Wave and UV Effect User Manual

beamZ 153.683 V2.0 LEDWAVE LED Jellyball Water Wave and UV Effect

Product Information: LEDWave Strobe Light

Model Number: 153.683 V2.0

The LEDWave Strobe Light is a lighting device that produces bright, flashing lights in various colors. It has multiple modes, including Automatic and Sound-Active modes. The strobe light also features a UV light option, which can be turned on or off using the remote controller. The strobe light should be connected to a protected circuit and must have an appropriate electrical ground to avoid the risk of electrocution or fire.

Technical Specifications

The technical specifications of the LEDWave Strobe Light are listed below:

• Model Number: 153.683 V2.0
• Power Supply: AC 100-240V 50/60Hz
• Power Consumption: 20W
• LEDs: 12 x 1W (4 x Red, 4 x Green, 4 x Blue)
• Strobe Rate: 0-10Hz
• Dimensions: 200 x 92 x 142mm
• Weight: 0.6kg

Usage Instructions

Before using the LEDWave Strobe Light, carefully read the instruction manual provided and keep it for future reference. The following usage instructions should be followed:

1. Before connecting the strobe light to the power outlet, verify that the mains voltage and frequency match the values specified on the equipment.
2. If the included power cord or power adapter does not fit in your wall outlet, contact your electrician.
3. Connect the strobe light to a protected circuit (circuit breaker or fuse) and ensure it has an appropriate electrical ground to avoid the risk of electrocution or fire.
4. Press the red button on the strobe light to turn it on. Press again to turn it to standby mode.
5. To turn on Automatic mode, press the corresponding button on the remote controller.
6. To change the color of the strobe, press the corresponding button on the remote controller.
7. To turn on the UV light, press the corresponding button on the remote controller. Press again to turn it off.
8. To turn on Sound-Active mode, press the corresponding button on the remote controller.
9. To change the strobe with LEDs, press the corresponding button on the remote controller.
10. To change the derby effect, press the corresponding button on the remote controller.

SAFETY INSTRUCTIONS

WARNING: Before carrying out any operations with the unit, carefully read this instruction manual and keep it with care for future reference. It contains important information about the installation, usage and maintenance of the unit.

• Unpack and check carefully that there is no transportation damage before using the unit
• Please read these instructions carefully and follow the instructions.
• Observe all safety warnings. Never remove safety warnings or other information from the equipment.
• Be sure that no ventilation slots are blocked; otherwise, the unit will overheat.

WARNING: Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the main power values match. If the included power cord or power adapter does not fit in your wall outlet, contact your electrician.

• After connecting the unit, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.
• Make sure that the power cord is never crimped or damaged. Check the unit and the power cord from time to time.
• Always disconnect power from the mains, when the unit is not used or before cleaning! Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
• Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.
• Do not switch the unit on and off in short intervals.
• Do not connect the unit to a dimmer pack.
• Install the unit in a well-ventilated place.
• Never place any material over the lens.
• Never let the sunlight lights directly to the front lens, even when the unit is not working.
• Always allow free air space of at least 50 cm around the unit for ventilation.
• Make sure that the area below the installation place is blocked when rigging, de-rigging, or servicing the unit.
• For mounting height >100 cm, always fix the unit with an appropriate safety rope. Fix the safety rope at the correct fixation points only. The safety rope must never be fixed at the transport handles!
• Never look directly at the light beam. Please note that fast changes in lighting, e. g. flashing light, may trigger epileptic seizures in photosensitive persons or persons with epilepsy.
• This unit is not designed for permanent operation. Consistent operation breaks will ensure that the unit will serve you for a long time without defects.

WARNING: If the power cord of the unit is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord.

• Make sure that the unit is not exposed to extreme heat, moisture, or dust.
• Clean the unit using a dry cloth.
• Do not touch the unit bare-handed during its operation (the housing becomes very hot). Allow the unit to cool for at least 5 minutes before handling.
• This unit is designed exclusively for indoor use, do not use this equipment in the immediate vicinity of fluid (does not apply to special outdoor equipment – in this case, observe the special instructions noted below). Do not expose this unit to flammable materials, fluids, or gases.
• If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.
• Never attempt to bypass the thermostatic switch or fuses.
• Do not dismantle or modify the unit.
• For replacement use fuses/bulbs of the same type and rating only.
• Repairs, servicing, and electric connection must be carried out by a qualified technician.
• The ambient temperature must always be between -5° C and +45° C.
• If this unit is operated in any other way, than the one described in this manual, the product may suffer damages and the warranty becomes void.
• Plastic bags must be kept out of reach of children.
• The unit must be installed out of the reach of children. Never leave the unit running unattended.

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling this product, please contact your local Civic Office, your household waste disposal service, or the shop where you purchased the product.

UNPACKING INSTRUCTION

CAUTION: Immediately upon receiving the product, carefully unpack the carton, and check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain the packing material for inspection if any parts appear damaged from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original factory box and packing. If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.

POWER SUPPLY

The label on the backside of the unit indicates the mains voltage to which it must be connected. Check that the mains voltage corresponds to this. Any other voltage than the one indicated may cause irreparable damage to the unit. The unit must also be connected directly to the mains voltage and no dimmer or adjustable power supply may be used.

WARNING: Always connect the unit to a protected circuit (circuit breaker or fuse). Make sure the unit has an appropriate electrical ground to avoid the risk of electrocution or fire.

REMOTE CONTROLLER

ON/OFF

Press the red button to turn the device on, and press again to turn in standby mode.

AUTO MODE

Automatic mode will enable you to run the automatic programs on the product.
To turn on Automatic mode, press on the remote controller.

COLOUR MODE

To change the color of the strobe, press .

UV MODE

To put the UV light on the press , put the UV light off the press once again.

SOUND MODE

To turn on Sound-Active mode, press on the remote controller.

LASER MODE

No function.

FLASH MODE

To change the strobe with LEDs, press .

MOTOR MODE

To change the derby effect.

1. Press (MOTOR) on the remote controller.
2. Press or change effect.

SPEED MODE

To change the speed of color change, color fade, sound active and strobe modes.

1. Press (SPEED) on the remote controller.
2. Press or to increase or decrease the speed of color change.

SENSITIVITY MODE

To adjust sound sensitivity in Sound-Active mode

1. Press on the remote controller.
2. Press or . to either increase or decrease sound sensitivity(note: only available in sound active mode).

CAUTION: The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery contacts prevents the battery from being discharged during storage. Prior to the first operation remove the foil from the battery support on the rear side of the remote control. Otherwise, the operation of the remote control is not possible. If the range of the remote control decreases, replace the battery. For this purpose, on the rear side of the remote control press the small bar with the groove to the right (1) and at the same time remove the battery support (2). For operation, one 3 V button cell type CR 2025 is required. When inserting, pay attention that the positive pole of the button cell shows upwards in the support.

CLEANING

The buildup of dust, dirt, and other airborne particles will reduce the unit’s light output. It will also prevent the unit from cooling correctly, and this will reduce the unit’s lifetime. The rate of dirt buildup will vary depending on environmental factors such as airborne dust, the use of smoke machines, airflow from ventilation systems, etc. The unit’s cooling fans will accelerate buildup, and any smoke particles that are present in the atmosphere will increase the tendency for dirt to clog. To get the best performance and lifetime from the unit, inspect it regularly and clean it as soon as you see signs of dirt buildup. Assess the operating environment each time you begin to use the unit. In dusty or smoky conditions, inspect the unit after a few hours and check it frequently the unit may attract dirt faster than you expect. Draw up a cleaning schedule that will make sure that dirt is removed before it can build up. Use the following guidelines:

• Disconnect the unit from power and allow it to cool completely before cleaning.
• Do not use solvents, abrasives or any other aggressive product to clean the unit.
• Vacuum or use low-pressure compressed air to remove dust and lose particles from surfaces and air vents. Prevent the blades of cooling fans from turning before you aim a vacuum or air jet at the fan, or you may spin the fan too fast and damage it.
• Clean glass components by wiping gently with a soft, clean, lint-free cloth moistened with a weak detergent solution. Put the solution on the cloth and not on the surface to be cleaned. Avoid rubbing glass surfaces.
• Dry the unit with a soft, clean, lint-free cloth or low-pressure compressed air before reapplying power.

REPLACING THE FUSE

If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug the main lead.

Procedure

• Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.
• Step 2: Remove the old fuse from the fuse holder.
• Step 3: Install the new fuse in the fuse holder.
• Step 4: Replace the fuse holder in the housing.

TROUBLESHOOTING

The checklist below may help you troubleshoot in the unlikely event that a problem occurs while using the product:

on. Check cables and connections.
 | Fuse blown or internal fault.| Replace the mean fuse or contact Beamz support or Beamz authorized service partner. Do not remove the base or yoke covers. Do not attempt to replace a fuse or carry out any repairs or service that are not described in this User Manual unless you have both authorizations from Beamz

support or Beamz authorized service partner.

Light output cuts out intermittently.| A unit is too hot.| Allow the unit to cool. Reduce ambient temperature. Ensure free airflow around the unit. Clean the unit if necessary.
 | LEDs damaged.| Disconnect the unit and contact Beamz support or Beamz authorized service partner.
 | The power supply settings do not match the local AC voltage and frequency.| Disconnect unit. Check settings and correct them if necessary.

TECHNICAL SPECIFICATIONS

• Light source: 5-in-1 LED
• LED colors: Red, Green, Blue, White, Ultra Violet
• Quantity of strobe LEDs: 4
• Beam angle: 6
• Modes: Automatic programs
• Power consumption: 0.5 – 0.2A
• Power supply : 100-240VAC 50/60Hz
• Dimensions (L x W x H) : 240 x 130 x 112
• Weight: 1.60 kg

Design and product specifications are subject to change without prior notice.
The products referred to in this manual conform to the European Community Directives to which they are subject:

European Union

• Tronios B.V.,
• Bedrijvenpark Twente Noord 18,
• 7602KR Almelo, The Netherlands
• 2014/35/EU
• 2014/30/EU
• 2011/65/EC

United Kingdom

• Tronios Ltd.,
• 130 Harley Street,
• London W1G 7JU, United Kingdom
• S.I. 2016:1101
• S.I. 2016:1091
• S.I. 2012:3032

is a leading developer of lighting products, including intelligent DMX moving heads, wireless battery operatedDMX effects, static washes, sound-activated club effects, strobes & blacklights, LED lighting, fog and special effects machines, lasers, and indoor and outdoor architectural lighting, as well as lighting controllers and protective bags. BEAMZLIGHTING.COM.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>