beamz 150.164 Starcolor54 Starcolor54 Tour User Guide

beamz 150.164 Starcolor54 Starcolor54 Tour

Product Information

Specifications

• Model: Starcolor54 Starcolor54 TOUR
• Model Number: 150.164 150.167 V1.0
• Communication Protocol: DMX512 with RDM
• Power Requirements: Refer to label on backside for mains voltage
• Terminating Resistor Value: 120 Ohm
• RDM UID: Unique identification number assigned to each unit

Product Usage Instructions

Power Connection
Before connecting the unit to the power outlet, ensure that the mains voltage and frequency match the specified values on the equipment. If there is a voltage selection switch, ensure the values match before connecting. If the included power cord does not fit your wall outlet, contact an electrician for assistance. Always connect the power cord to a grounded outlet to prevent electrical hazards.

DMX Connection
If using a standard DMX controller, connect the DMX output of the controller to the DMX input of the first unit in a chain. Continue connecting the output of one unit to the input of the next until all units are linked. For the last unit, close the DMX line with a terminating resistor by soldering a 120 Ohm resistor between signal (-) and signal (+) on an XLR connector connected to the DMX output of the last unit.

RDM Communication
This unit supports Remote Device Management (RDM) via DMX512. RDM allows bi-directional communication for configuration and status monitoring purposes without affecting non-RDM equipment. Utilize RDM functions to remotely set DMX start addresses and interact with specific fixtures in your setup. Each unit is assigned a unique RDM UID for identification.

Safety Precautions
Always connect the unit to a protected circuit with appropriate electrical grounding to avoid risks of electrocution or fire. Do not use dimmers or adjustable power supplies with the unit.

Frequently Asked Questions (FAQ)

• Q: How do I dispose of the product correctly?
  A: Do not treat the product as household waste. Instead, hand it over to an applicable collection point for recycling of electrical and electronic equipment. Contact your local Civic Office or waste disposal service for more information on proper disposal methods.

• Q: Can I use a dimmer with this unit?
  A: No, do not use dimmers or adjustable power supplies with this unit. Always connect it directly to mains voltage with appropriate grounding for safety.

SAFETY INSTRUCTION

WARNINGS Before carrying out any operations with the unit, carefully read this instruction manual and keep it with care for future reference. It contains important information about the installation, usage and maintenance of the unit.

• Unpack and check carefully that there is no transportation damage before using the unit
• Please read these instructions carefully and follow the instructions.
• Observe all safety warnings. Never remove safety warnings or other information from the equipment.
• Be sure that no ventilation slots are blocked; otherwise the unit will overheated.

WARNINGS Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or power adapter does not fit in your wall outlet, contact your electrician.

• After connecting the unit, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.
• Make sure that the power cord is never crimped or damaged. Check the unit and the power cord from time to time.
• Always disconnect power from the mains, when unit is not used or before cleaning! Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
• Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.
• Do not switch the unit on and off in short intervals.
• Do not connect the unit to a dimmerpack.
• Install the unit in a well ventilated place.
• Never place any material over the lens.
• Never let the sunlight lights directly to the front lens , even when the unit is not working.
• Always allow free air space of at least 50 cm around the unit for ventilation.
• Make sure that the area below the installation place is blocked when rigging, derigging or servicing the unit.
• For mounting height >100 cm, always fix the unit with an appropriate safety-rope. Fix the safety-rope at the correct fixation points only. The safety-rope must never be fixed at the transport handles!
• Never look directly at the light beam. Please note that fast changes in lighting, e. g. flashing light, may trigger epileptic seizures in photosensitive persons or persons with epilepsy.
• This unit is not designed for permanent operation. Consistent operation breaks will ensure that the unit will serve you for a long time without defects.

WARNINGS If the power cord of the unit is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord.

• Make sure that the unit is not exposed to extreme heat or dust.
• Clean the unit using a dry cloth.
• Do not touch the unit bare-handed during its operation (housing becomes very hot). Allow the unit to cool for at least 5 minutes before handling.
• Do not expose this unit to flammable materials, fluids or gases.
• If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.
• Never attempt to bypass the thermostatic switch or fuses.
• Do not dismantle or modify the unit.
• For replacement use fuses/bulb of same type and rating only.
• Repairs, servicing and electric connection must be carried out by a qualified technician.
• The ambient temperature must always be between -5° C and +45° C.
• If this unit is operated in any other way, than the one described in this manual, the product may suffer damages and the warranty becomes void.
• Plastic bags must be kept out of reach of children.
• Unit must be installed out of the reach of children. Never leave the unit running unattended.

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

UNPACKING INSTRUCTION

CAUTION Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original factory box and packing. If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.

POWER SUPPLY
The label on the backside of the unit indicates the mains voltage to which it must be connected. Check that the mains voltage corresponds to this. Any other voltage than the one indicated may cause irreparable damage to the unit. The unit must also be connected directly to the mains voltage and no dimmer or adjustable power supply may be used.

WARNING! Always connect the unit to a protected circuit (circuit breaker or fuse). Make sure the unit has an appropriate electrical ground to avoid the risk of electrocution or fire.

RIGGING

The unit may be set up on a stable and even surface. By means of the fixing facilities of the baseplate, the unit can also be mounted upside down to a truss, see below picture. For fixing, certified clamps with correct save working load are required. According to the figure, the quick lock bolts of the omega brackets are placed into the openings provided in the base plate and turned clockwise until they lock (to the stop). The mounting place must be of sufficient stability and be able to support a weight of 10 times of the unit’s weight. Secure the unit with a safety cable so that it cannot fall down. When carrying out any installation, always comply European and national guidelines concerning rigging, truss and all other safety issues. Always let the installation checked out by an authorized dealer!

DMX512 CONTROL

If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first unit in a DMX chain. Always connect the output of one unit with the input of the next unit until all units are connected.
CAUTION! At the last unit, you must close the DMX line with a terminating resistor. Take an XLR connector and solder a 120 Ohm resistor between signal (-) and signal (+) and connect it to the DMX output of the last unit in the line.

RDM CONTROL
This unit can communicate using RDM (Remote Device Management) via DMX512. RDM is a bi-directional communication protocol for use in DMX512 control systems, it is the open standard for DMX512 configuration and status monitoring. The RDM protocol allows data packets to be inserted into a DMX512 line without affecting the existing non-RDM equipment. The system allows a controller or special RDM controller to send and receive commands from specific fixtures. The RDM function allows you, for example to remotely set the DMX start address of your fixtures. This is especially useful when the fixture is installed in an inaccessible location. Each unit has an RDM UID (unique identification number).

REMOTE CONTROLLER

POWER
Press ‹ POWER> to put the device in standby mode or on.

AUTO MODE
Automatic mode will enable you to run the automatic programs on the product.
To turn on Automatic mode:

1. Press < AUTO> on the remote controller.
2. Press ‹AUTO1> or ‹AUTO2 › to choose between the different auto programs.

SOUND MODE
Sound-Active mode will enable the product to respond to the music.
To turn on Sound-Active mode:

1. Press «SOUND> on the remote controller.
2. Press < SOUND1> or ‹SOUND2› to choose between the different sound programs.

STROBE MODE
To adjust the strobe speed of the automatic program and the sound active program.

1. Press ‹ STROBE > on the remote controller.
2. Press ‹ UP> or ‹DOWN> to either increase or decrease the speed of the program.

SPEED MODE
To adjust the speed of the automatic program and the sound active program.

1. Press ‹ SPEED> on the remote controller.
2. Press ‹ UP> or ‹DOWN› to either increase or decrease the speed of the program.

DMX / % MODE
To enable DMX or disallow DMX on the product. Press < DMX> on the remote controller, the product work on the DMX controlling modes.

MANUAL MODE

1. Press ‹ MANUAL > on the remote controller.
2. Press . ‹G>. , (red, green, blue) to choose your colour.
3. Press again . ‹G›. ‹B>, (red, green, blue) to close your colour.
4. Press « UP> or «DOWN› to either increase or decrease the percentage of each colour.