BEGA 12223 LED Ceiling and Wall Luminaire Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

12223 LED Ceiling and Wall Luminaire
Application
Product description
Safety
Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

12223 LED Ceiling and Wall Luminaire
Instruction Manual

Ceiling and wall luminaire for indoor use

12223 LED Ceiling and Wall Luminaire

BEGA 12223 LED Ceiling and Wall Luminaire Instructions for use

Application

Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass, satin matt and aluminium alloy housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required. Luminaire with a high protection class.

Product description

Luminaire made of aluminium alloy Finish Colour white
Hand-blown opal glass, satin matt, with sliding-bolt closure
2 mounting holes ø 5.5 mm
Distance apart 130 mm
1 cable entry for mains supply cable up to ø 10.5 mm max. 3 x 1.5@
Connection terminal 2.5@
Earth conductor connection
LED power supply unit
220-240 V y 50-60 Hz
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 44
Protected against granular foreign bodies ≥ 1 mm and splash water
Impact strength IK03 Protection against mechanical impacts < 0.35 joule
– Safety mark
– Conformity mark
Weight: 1.1 kg
This product contains light sources of energy efficiency classes D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp

Module connected wattage	6.7 W
Luminaire connected wattage	8.4 W
Rated temperature	ta = 25 °C
Ambient temperature	ta max = 30 °C

12 223 K27

Module designation	LED-0521/927
Colour temperature	2700 K
Colour rendering index	CRI > 90
Module luminous flux	1090 lm
Luminaire luminous flux	769 lm
Luminaire luminous efficiency	91,5 lm / W

12 223 K3

Module designation	LED-0521/930
Colour temperature	3000 K
Colour rendering index	CRI > 90
Module luminous flux	1105 lm
Luminaire luminous flux	780 lm
Luminaire luminous efficiency	92,9 lm / W

Installation

LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Lead mains supply cable through the cable entry into the luminaire housing.
Fix the luminaire housing with enclosed or any other suitable fixing material onto the mounting surface.
It is imperative to use the enclosed gaskets.
Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.
Insert the opal glass into the luminaire housing with sliding bolt glass closure and turn the glass clockwise up to the stop.
Place glass to the luminaire housing and observe that the holding spring bolts fit into the notches of the glass.
Turn the glass clockwise until it is locked.
Thus, you reach a safe and vibration-resistant holding of the glass.
To release the glass from the luminaire housing, turn it counter-clockwise.
Replacement of the LED module ·Maintenance
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system.
Unscrew glass from luminaire housing by turning it counter-clockwise.
Clean glass and luminaire regularly with solvent-free cleansers from dirt.
Please follow the installation instructions for the LED module.
Screw in glass by turning it clockwise as far as it will go.
A broken glass must be replaced.